Question about 2000 Mitsubishi Galant

1 Answer

Automatic Transmision not shifting into high gear

I have a short circuit on fuse number 10 in the passenger paney, when it blows appears to affect the transmission. but when I look that fuse is supposed to protect the reverse light circuit. when it is off the SRS light comes on along with the check engine light

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 20 Answers

SOUNDS LIKE U HAVE SHORT IN REVERSE LIGHT SWITHCH

Posted on Nov 30, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7 Answers

SOURCE: automatic transmission Shift problem

you should first check gear box oil ,level and clean filter.lee

Posted on Jan 31, 2009

djicenova
  • 319 Answers

SOURCE: Pajero IO (auto) Super select 4WD-i problems

Check Linkage for the 4WD transfer case, between the shifter and the case. if it is a direct case mounted shifter, you may need to remove it and check for obstruction.

Have you tried to shift it to 4H while at a slow roll in N? Sometimes that used to work for me in my older floor mount 4WD truck. Give it try!

Posted on Feb 27, 2009

  • 52 Answers

SOURCE: 97 mitsubishi eclipse transmission problems automatic 2.0

I have a 95 Eclipse and I recently had to change out my TCU........ Transmission Control Unit, This should be located directly beneath the center console. First I would have the transmission services if problem persist then proceed to changing out the TCU you can get off of ebay. As far as i know there should be 3 Computers in our cars. 1 the Electronic Control Unit located behind radio 2 Transmission Control Unit located under center console and 3 Airbag Control Unit located under hood, Hope this helps.

Posted on Mar 06, 2009

  • 1 Answer

SOURCE: automatic is not shifting to overdrive

Problem solved. I found on the www the wiring diagram, corresponding to the o/d switch. I saw that there is a engine coolant temp switch (at coolant outlet of engine). the connector to it was corroded. So cleaning it,...o/d is now working proper.

Posted on Apr 02, 2009

sodeep
  • 3267 Answers

SOURCE: 1992 Mitsubishi lancer GLXI check engine light sensor appear

Well the sensors are reporting a failure in the engine/transmission. So either they are right or wrong has to be assessed by the nature of the alarms or sensor faliure, but the problem remains, hence if all primary steps of investigation start by hooking up to a PC specially built to rectify such problems. This facility is available at most of the gas service stations/centers..................sodeep

Posted on Jul 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Short in brake lite circute


check your wires properly there is a short somewhere thats why its blowing the fuse

Oct 23, 2012 | 2012 Maserati Quattroporte S Sedan 4.7L V8...

1 Answer

The "D" light is blinking regard less where the


Flashing D4 light is an error from the TCU (transmission control unit), so you got something going on with your transmission. If you want to pull the error code, remove the passengers side kick panel and look for a pair of wires with a blue connector at the end. Stick a paper clip or some other piece of wire into each hole of the connector to short the wires. Put your key in the ignition and turn 2 clicks. The D4 light will flash the code...short flashes=1 and long flashes=10. Add the number of short and long flashes to get your code. Errors are below:

0-Transmission control unit (TCU) faulty.
1-Lock-up solenoid 'A' circuit open or shorted.
2-Lock-up solenoid 'B' circuit open or shorted.
3-Throttle Position Sensor circuit open or shorted.
4-Vehicle Speed Sensor open or shorted - No signal from speedometer.
5-Shift Lever Position Switch circuit shorted.
6-Shift Lever Position Switch circuit open.
7-Shift Solenoid 'A' circuit open or shorted.
8-Shift Solenoid 'B' circuit open or shorted.
9-Counter shaft or transmission speed pulse generator open or shorted.
10-Coolant Temperature Sensor open or shorted.
11-Engine RPM (Ignition coil signal) open or shorted.
12-(No code 12 used)
13-Main shaft speed pulse generator open or shorted.
14-Linear (line pressure control) solenoid open or shorted.
15-Kick down switch circuit shorted.

Dec 18, 2010 | 1993 Honda Accord

1 Answer

GOLF 1998 1.9 TDI transmision automatic


Go to carhelpsite.com it is free as long as you click on 2 of the ads at the website then your questions will be answered by an ASE certified mechanic,you don't have to buy or fill out anything on the ads,so help keep the site free.

Apr 14, 2010 | 2002 Volkswagen Golf

1 Answer

Will not shift into 2nd gear on a automatic trans


Trans shifts into gear harshly, car feels sluggish off the line, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmision is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the underhood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

What is "limp-home mode" ? This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Thank you for using fixya and good luck

Apr 10, 2010 | 1994 Chevrolet S-10 Blazer

1 Answer

1991 accord, auto trans: green sport light is flashing. WHY???


It is either your Vehicle Speed Sensor (easy to change) or your Automatic Transmission Computer (capacitors burn out on these boards, there is a fix for this too, the picture is at the bottom of this page). You need to diagnose by removing the lower right plastic kick panel on the passenger side. There you will find a blue plug. With the car OFF stick a paper clip, wire or stuff the plug with foil to make electrical connection so that the two terminals are touching. Then, turn the ignition to ON (not enough to start it though, just power it up). When you do this, count the blinks in the "S Light" or count your blinking Check Engine Light. Both are different but can refer to different things wrong with your car. A long blink is the first number and the short blinks that follow are the second number.
So imagine this as being 14 : ___ _ _ _ _

Below is a decoding chart:

The first section will be the check engine light codes2_bing.gif, the next one is the Transmission Control Unit Codes read from the S Light;

1 O2A - Oxygen sensor #1
2 O2B - Oxygen sensor #2
3 MAP - manifold absolute pressure sensor
4 CKP - crank position sensor
5 MAP - manifold absolute pressure sensor
6 ECT - water temperature sensor
7 TPS - throttle position sensor
8 TDC - top dead centre sensor
9 CYP - cylinder sensor
10 IAT - intake air temperature sensor
12 EGR - exhaust gas recirculation lift valve
13 BARO - atmospheric pressure sensor
14 IAC (EACV) - idle air control valve
15 Ignition output signal
16 Fuel injectors
17 VSS - speed sensor
19 Automatic transmission lockup control valve
20 Electrical load detector
21 VTEC spool solenoid valve
22 VTEC pressure valve
23 Knock sensor
30 Automatic transmission A signal
31 Automatic transmission B signal
36 traction control found on JDM ecu's
41 Primary oxygen sensor heater
43 Fuel supply system
45 Fuel system too rich or lean
48 LAF - lean air fuel sensor
54 CKF - crank fluctuation sensor
58 TDC sensor #2
61 Primary oxygen sensor
63 Secondary oxygen sensor
65 Secondary oxygen sensor heater
71 random misfire cylinder 1
72 random misfire cylinder 2
73 random misfire cylinder 3
74 random misfire cylinder 4
80 Exhaust Gas Recirculation insufficient flow detected
86 ECT Sensor (Engine Coolant Temperature) circuit range / performance problem
90 Evaporative Emission Control System leak detected in the fuel tank area
91 Fuel Tank Pressure Sensor low input
92 Evaporative Emission Control System insufficient purge flow

TCU Codes:

CODE LIST:

1-Lock-up solenoid 'A' circuit open or shorted.
2-Lock-up solenoid 'B' circuit open or shorted.
3-Throttle Position Sensor circuit open or shorted.
4-Vehicle Speed Sensor open or shorted - No signal from speedometer.
5-Shift Lever Position Switch circuit shorted.
6-Shift Lever Position Switch circuit open.
7-Shift Solenoid 'A' circuit open or shorted.
8-Shift Solenoid 'B' circuit open or shorted.
9-Counter shaft or transmission speed pulse generator open or shorted.
10-Coolant Temperature Sensor open or shorted.
11-Engine RPM (Ignition coil signal) open or shorted.
12-(No code 12 used)
13-Main shaft speed pulse generator open or shorted.
14-Linear (line pressure control) solenoid open or shorted.
15-Kick down switch circuit shorted.
b9fa7bc.jpg

Feb 14, 2010 | 1991 Honda Accord

1 Answer

I have a 92 accord. Automatic Trans... Doesnt move.


It is either your Vehicle Speed Sensor (easy to change) or your Automatic Transmission Computer (capacitors burn out on these boards, there is a fix for this too, the picture is at the bottom of this page). You need to diagnose by removing the lower right plastic kick panel on the passenger side. There you will find a blue plug. With the car OFF stick a paper clip, wire or stuff the plug with foil to make electrical connection so that the two terminals are touching. Then, turn the ignition to ON (not enough to start it though, just power it up). When you do this, count the blinks in the "D Light" or count your blinking Check Engine Light. Both are different but can refer to different things wrong with your car. A long blink is the first number and the short blinks that follow are the second number.
So imagine this as being 14 : ___ _ _ _ _

Below is a decoding chart:

The first section will be the check engine light codes2_bing.gif, the next one is the Transmission Control Unit Codes read from the D Light;

1 O2A - Oxygen sensor #1
2 O2B - Oxygen sensor #2
3 MAP - manifold absolute pressure sensor
4 CKP - crank position sensor
5 MAP - manifold absolute pressure sensor
6 ECT - water temperature sensor
7 TPS - throttle position sensor
8 TDC - top dead centre sensor
9 CYP - cylinder sensor
10 IAT - intake air temperature sensor
12 EGR - exhaust gas recirculation lift valve
13 BARO - atmospheric pressure sensor
14 IAC (EACV) - idle air control valve
15 Ignition output signal
16 Fuel injectors
17 VSS - speed sensor
19 Automatic transmission lockup control valve
20 Electrical load detector
21 VTEC spool solenoid valve
22 VTEC pressure valve
23 Knock sensor
30 Automatic transmission A signal
31 Automatic transmission B signal
36 traction control found on JDM ecu's
41 Primary oxygen sensor heater
43 Fuel supply system
45 Fuel system too rich or lean
48 LAF - lean air fuel sensor
54 CKF - crank fluctuation sensor
58 TDC sensor #2
61 Primary oxygen sensor
63 Secondary oxygen sensor
65 Secondary oxygen sensor heater
71 random misfire cylinder 1
72 random misfire cylinder 2
73 random misfire cylinder 3
74 random misfire cylinder 4
80 Exhaust Gas Recirculation insufficient flow detected
86 ECT Sensor (Engine Coolant Temperature) circuit range / performance problem
90 Evaporative Emission Control System leak detected in the fuel tank area
91 Fuel Tank Pressure Sensor low input
92 Evaporative Emission Control System insufficient purge flow

TCU Codes:

CODE LIST:

1-Lock-up solenoid 'A' circuit open or shorted.
2-Lock-up solenoid 'B' circuit open or shorted.
3-Throttle Position Sensor circuit open or shorted.
4-Vehicle Speed Sensor open or shorted - No signal from speedometer.
5-Shift Lever Position Switch circuit shorted.
6-Shift Lever Position Switch circuit open.
7-Shift Solenoid 'A' circuit open or shorted.
8-Shift Solenoid 'B' circuit open or shorted.
9-Counter shaft or transmission speed pulse generator open or shorted.
10-Coolant Temperature Sensor open or shorted.
11-Engine RPM (Ignition coil signal) open or shorted.
12-(No code 12 used)
13-Main shaft speed pulse generator open or shorted.
14-Linear (line pressure control) solenoid open or shorted.
15-Kick down switch circuit shorted.

c96e887.jpg

Feb 13, 2010 | 1992 Honda Accord

1 Answer

Have a 94 gmc 1500 4.3 automatic when i put it in drive it doesn't shift if i manuely shift from first to drive it will shift it doesn't have any slipping it also has overdrive that doesnt seem to work any...


Transmission does not shift automatically, only manually. Swap in a known-good PCM, check wiring, check other sensors such as VSS and TPS.

Trans shifts into gear harshly, car feels sluggish off the line
, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmision is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the underhood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Good luck and get back to me, hope this helps.

Nov 16, 2009 | 1994 GMC Sierra

3 Answers

Fuse # 10 at drivers door fuse box keeps blowing. It would blow once a week at first, now it blows immeadeately. Please advise.


you have a short in that circuit get you a wiring diagram at the library for your car model and trace the wires most likely one is necked and every time it makes contact with the car body it blows the fuse, it is a pains taking task but can be done just be pationt

Sep 21, 2009 | 1996 Dodge Neon

1 Answer

1994 s-10 stays in high gear


try and service the transmision filter and fluid and add a suppliment call LUBE GUARD u get this at NAPA/valve body is stuck

Jun 29, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

Stop light and gear shift lock not working


check the switch on the brake pedal.it may be cracked and not sending power to the interlock solenoid,and there may be a short,which will blow the fuse.check the wiring around the rear lights and make sure the harness has not been rubbing on sharp metal

Jun 04, 2009 | 1994 Toyota Corolla

Not finding what you are looking for?
2000 Mitsubishi Galant Logo

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...