Question about 2002 Daewoo Lanos

1 Answer

NEED TO KNOW WHAT CODE PO137,PO141,PO452 MEAN FOR A 2000 DAEWOO NUBIRA

CODES CAME UP NEED TO CLEAR OR FIX TO PASS SMOG

Posted by on

Ad

1 Answer

Two codes are for an oxygen sensor & the 452 for the evap system

Google OBD2 Systems followed by the code

Posted on Nov 29, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: replacing timing belt on daewoo nubira 2000 model

Instructions Difficulty: Moderate Things You’ll Need:

  • Set of ¼-inch drive sockets ¼-inch drive ratchet Set of ½-inch drive sockets ½-inch drive ratchet Set of 3/8-inch drive sockets 3/8-inch drive ratchet Set of metric wrenches Floor jack Jack stands
Step1 Raise and support the vehicle on jack stands. Remove the intake air temperature wiring, the breather hose and intake air hose. Take off the air cleaner assembly. Step2 Remove the right wheel. Remove the accessory belts. Remove the crankshaft bolt and the crankshaft pulley. Remove the power steering bolts and the timing belt covers. Temporarily install the crankshaft bolt and turn the engine clockwise until the mark on the crankshaft pulley, which is a triangle stamped into the crank sprocket, is aligned with the corresponding triangular mark on the block. Step3 Make sure that the timing marks are aligned on the camshaft sprockets. These are a line on each sprocket that runs through a tooth on each sprocket. These lines should line up in the middle between each sprocket and point toward each other. If they do not line up, turn the crankshaft one more time and they will line up. It takes two turns of the crank to one complete revolution of the cam. Step4 Loosen the water pump bolts; using the 3/8-inch ratchet, turn the water pump clockwise away from the belt and loosely tighten the bolts to keep it there. Remove the timing beltmag-glass_10x10.gif. Make sure the timing marks are aligned and install the new belt starting on the right side from the crank sprocket and working counterclockwise. Keep all the belt tension on the right side away from the tensioner. Step5 Loosen the bolts in the water pump and rotate the water pump counterclockwise to apply tension to the belt. Watch the tensioner, which is above the water pump, and apply tension with the water pump until the pointer on the tensioner lines up with the notch above it. Lightly tighten the water-pump bolts. Step6 Turn the engine two more times and align the timing marks perfectly. Loosen the water-pump bolts and, using the ratchet, apply tension to the belt until the tensioner pointers are aligned. Tighten the water-pump bolts. Step7 Install the timing-belt covers and the bolts in the power-steering pump and tighten. Remove the crankshaft bolt and install the crank pulley and the bolt, then torque the crankshaft pulley bolt to 70 foot pounds of torque. Install all components in reverse order of removal.

Posted on Mar 08, 2009

greg_margo
  • 1959 Answers

SOURCE: 2000 daewoo nubira need serpentine belt routing

The following link will take you to a diagram for your car. Best of Luck!
Greg
http://www.mvreader.com/multiview/dayco/zoom.php?zoom_item=C0000B&l=n&catalog=auto&category=2

Posted on May 16, 2009

  • 176 Answers

SOURCE: Need to remove heater core from 2000 Daewoo Nubira

  1. Disconnect the negative battery cable.
  2. Remove the instrument panel from the vehicle.
  3. Remove the heater/air distributor case from the vehicle.
  4. Disconnect the vacuum actuators from the vent/floor door and the defroster door.
  5. Remove the vacuum actuators from the heater/air distributor case.
  6. Remove the screws that secure the heater core cover to the heater/air distributor case assembly.
  7. Slowly separate the lower heater core cover from the rest of the assembly
  1. Remove the screw and the bracket clamp that secure the heater core lines to the case.
  2. Remove the spring clamp that secures the heater core body to the case.
  3. Remove the heater core from the case.
  1. Install the heater core into the case.
  2. Secure the heater core lines to the case with the retaining bracket clamp and the screw. Tighten the heater core retaining bracket screw .
  3. Install the heater core body with the retaining spring clamp.
  1. Install the heater core cover.
  2. Install and tighten the screws that secure the heater core cover to the heater/air distributor case assembly. Tighten the heater core cover screws
  3. Install the actuators for the vent/floor and the defroster doors.
  4. Install the heater/air distributor case.
  5. Install the instrument panel.
  6. Fill the cooling system
  7. Connect the negative battery cable.

Posted on Jun 18, 2009

MNfisherman
  • 11896 Answers

SOURCE: need to check transmission fluid

you will have to raise the vehicle. Look on tranny. You will see two plugs, a lower side drain plug and a higher side check/fill plug. Remove higher side plug, stick your finger in the hole. If you can feel the fluid at top of hole, then it is full, if not, then you will have to add some which is always the tricky part.

Posted on Aug 07, 2009

  • 1986 Answers

SOURCE: How to scan the 2001 daewoo nubira fault codes.

Your port should be located under the dash on the driver's side near your knee area. The port should be pointing straight down from the dash. The scanner will be plug and play and you shouldn't have to jump and pins for the OBD-II port. As for the codes, there are so many thousands of codes that you can't even guess what codes will be generated from your scan

Posted on Sep 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have two codes come up when checking why my check engine light is on. P0447 and P0420. Any info on what these mean and what it takes to fix so I can pass my smog test??


press the helpful button
Definition of P0420 is catalyst below threshold. This is indicative of (among other things) a converter that is not working as efficiently as it should be (according to specs). Catalytic converters are not normally a "wear" type item, that is they are not deisgned to wear out and need replacement. If they have failed, it is likely due to something else that caused it to fail.

P0447 Evaporative Emission Control System Vent Valve/Solenoid Circuit Open. The Powertrain Control Module (PCM) has detected an open within the circuit that controls the vent valve or solenoid for evaporative emission systems vapor.

Read more at: http://www.obd-codes.com/p0447
Copyright OBD-Codes.com

http://www.trouble-codes.com/

http://www.obd-codes.com/trouble_codes

Jan 26, 2016 | Hyundai Motor 2002 Elantra

1 Answer

Turn off or rest check engine light to pass smog


It takes at least one "Good trip" stored in the computer before it will pass a smog check. Simply resetting the light did not fix the problem that caused the light to come on to begin with, and attempting to smog it will only result in a failed test.
You must address the fault first, then reset the system and drive upwards of 150 miles before a "Good trip" has been stored in the computer.

Mar 30, 2015 | 2003 Toyota Avalon XLS

2 Answers

P0308 code intermintently pops up can i pass smog


  • Check Engine Lightflashing
  • Rough running, hesitation, and/or jerking when accelerating
  • In most cases, there are no adverse conditions noticed by the driver
  • In some cases, there may be performance problems, such as dying at stop signs or rough idling, hesitation, misfires or lack of power (especially during acceleration), and a decrease in fuel economy

OBD diagnostic tool

May 08, 2014 | 2001 Dodge Durango

1 Answer

1998 dodge 1500 rejected smog test


you really need to drive it for min of 30 minutes before you go, they need time to heat up and run a cycle,

Dec 06, 2013 | 1998 Dodge Ram 1500 4WD

1 Answer

Won't pass smog when it should...


Just because the car seems to run well, does not mean the emissions are within spec. For example, you could be running a little rich and the car will start and run great, but the exhaust is not within code.
What you can do is take it to a "smog shop", that is a repair shop with the proper equipment to diagnose the problem. If the testing is simply the reading of the on board computer codes, then most any place can read those, but you need an experinced mech to know what to do about it. May need an exhaust gas analyzer to physically sample and analyse the gasses. For the actual test, as long as the computer says all is fine, usually, you're good to go.
If the computer looses power any saved run data will be lost and must be re-accumulated to pass the smog test. A few hours to a day is usually enough run time to accumulate enough data.

Dec 04, 2013 | 1999 Saturn SL

1 Answer

How can I reset my '99 caddy sts's computer in order to pass my smog


You can use a code reader/coder clearer handheld device at any of the major auto dealers to clear the code. The device plugs into your dashboard on the left side of the steering wheel at the bottom.. Normally, you can clear the code and drive for about 15 minutes (maybe more if you are gentle on the gas) before the code appears again. These code readers cost about $80 to $100.

May 01, 2013 | Cadillac DeVille Cars & Trucks

1 Answer

2001 Tahoe no check engine light. will not pass smog due to stored trouble codes. air valves , catalytic converter


you have to have the codes erased and then drive for a while, at least 100 miles and it should pass providing there are no other issues.

Sep 04, 2012 | Chevrolet Tahoe Cars & Trucks

1 Answer

My 1999 kia sephia wont pass smog test


You will need to get it scanned and get the codes for the problem. If it failed the test due to emissions I would almost guarantee it will be your oxygen sensor or cat

Jul 31, 2012 | 1999 Kia Sephia

1 Answer

Need list of fault codes for deawoo lanos 1999


Not a solution: This is my problem...
I needed to get my car smogged, but the check engine light was on. Took to to a local smog station that had replaced a sensor for me in the past in order to pass smog. They could not fix it. Put car in dealership garage for repairs and to date, the transmission module sensor (computer) went out and the ignition sensor was out also. The mechanic replaced both and now the code P1702 comes up. What does that code mean? My car still won't pass smog....

Aug 06, 2008 | Daewoo Lanos Cars & Trucks

Not finding what you are looking for?

Open Questions:

See all 2002 Daewoo Lanos Questions

2002 Daewoo Lanos Logo

Related Topics:

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

80407 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...