Question about 2006 Hummer H3

1 Answer

What are the torqe specs for 2006 H3 fan/clutch and water pump

Need torque specs for 2006 H3 fan clutch and water pump replacement and what special tools?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hummer Master
  • 14,036 Answers

Special tools you need EN 48543 FAN CLUTCH HOLDING TOOL. J41240 FAN CLUTCH REMOVER AND INSTALLER. TORQUE FOR FAN CLUTCH NUT 41 LB FT. FOUR BOLTS TO FAN BLADE TORQUE 20 LB FT.WATER PUMP BOLTS TORQUE TO 11 LB FT. DONT NEED SPECIAL TOOLS REMOVE WATER PUMP.

Posted on Dec 31, 2012

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 2006 H3 Hummer AC/Heater Fan Motor

I brought my 2006 H3 in to the dealer for the same thing. My blower stopped working all together but it started as an intermittent problem. He said he had to replaced a diode or resistor either behind the switch on the dash that controls the fan or on the fan motor itself. Have not had a problem since but that was only about 4 months ago.

Posted on Apr 09, 2009

mecanica03
  • 881 Answers

SOURCE: water pump removal

yes , you need a special tool to remove fan clutch to shaft

Posted on Apr 24, 2009

  • 1 Answer

SOURCE: 2006 H3 Hummer fan problem

Hi if your internal fan not work in any position well i fixed up myself easy and save your money.
locate the fan motor air just outside right courtesy drawn document in front of passenger. go from down and look up you will see a motor with a big connector white with 2 screw secure inside the motor block. loose the two screws and pull out gently the connector from motor fan block. you will see a green multiresistor connected with this big connector. Usually the first + voltage connector is burnet out. disconnect the connector pull from resistor and check for any burn. in my case the first pin was burned out completely
you can buy another connector or you can clean the burned connector take out form connector weld a small copper cable of 5 mm dia from resistor to the burn cable and reconnect the connector without buy a new one. after replace again the resistor in the hole of motor blow with the 2 screw.
Done all work again without buy another new connector.
Gabriel from Italy Turin
H3 hummer 2007
loveling one and Humvee owner

Posted on Jun 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

On Nssan Frontier 1999 2.4L I am replacing the waterpump and fan clutch. I need to know the torque measurements for the pump- and clutch nuts.


Go to autozone.com and they have free online books you can look it up just enter make model and engine type

hope this helps mike

Jul 20, 2016 | 1999 Nissan Frontier

1 Answer

Can anyone.tell me the Torqe specs for a 2004 or cruiser


Head and Cam Bolt Torque specs? - PT Cruiser Forum

www.ptcruiserlinks.com > ... > Tech & Performance Forum

Nov 5, 2012 - 2 posts - ‎2 authors
I am putting everything back on after replacing the head gasket. I was wondering what the Torque Specs and Sequences are for both the Head ... Torque Specs
10 posts
Jul 28, 2012
Valve cover torque specs
5 posts
Jul 4, 2011
Timing Repair Project - Bolt Torque Specs
7 posts
Jun 16, 2011
torque specs?
9 posts
Mar 20, 2006
More results from www.ptcruiserlinks.com

Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts ...

? 5:07
https://www.youtube.com/watch?v=2wB2o27eWgo
Aug 20, 2015 - Uploaded by World Mechanics
Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts Install and Torque Specs 2.4 Engine. ... 2004 Chrysler PT CruiserCamshaft Install

Dodge Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head ...

? 6:08
https://www.youtube.com/watch?v=7rY7tDbye-8
Aug 16, 2015 - Uploaded by World Mechanics
... Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head gasket Install and torque specs We took this video to ... 2004 Chrysler PtCruiser head gasket

Jan 18, 2016 | Cars & Trucks

1 Answer

How do i replace the fan clutch on a 95 lincoln


You need a special tool to undo the large nut that threads the fan clutch onto the water pump shaft, even with that kit you have a really hard time getting it off if you haven't done it before. Contact Snap-ON tools or MAC tools dealers for the special kit needed. About $100.00

Jul 24, 2012 | 1995 Lincoln Town Car

1 Answer

95' ford econline 350 van replacing waterpump and clutch fan how to replace.


TO REPLACE WATER PUMP.REMOVE THE RADIATOR SHROUD HALVES.REMOVE FAN CLUTCH AND FAN.YOU NEED FAN CLUTCH WRENCH AND A FAN CLUTCH PULLEY HOLDER.YOU CAN RENT TOOLS AT AUTO ZONE OR BUY THEM AT A AUTO PARTS STORE.THE FAN CLUTCH BOLTS ARE LEFT HAND THREAD. REMOVE THEM BY TURNING CLOCKWISE.BEFORE INSTALLING NEW WATER PUMP COAT BOTH SIDES OF WATER PUMP GASKET WITH GASKET SEALER.TORQUE WATER PUMP BOLTS 18 FT LBS.

Mar 15, 2011 | 1995 Ford Econoline

1 Answer

How do you remove water pump from it"s housing!


When removing the pump unit with special tool (some auto-parts stores rent them), TURN CLOCKWISE TO LOOSEN the pump-unit, counter-clockwise to tighten. The Torq Specs for the pump-unit is: 73 Foot Pounds. There are stop tabs on the pump-unit that mate with the tab stoppers on the main water pump housing unit. I had to re-torq by visually viewing where the stop tabs where after the first torq, don't over-torq or you will bend the tab stoppers on the pump unit. ALSO...the water pump-unit front cover requires a new rubber gasket (you'll have to order it through GM or use RTV silicone under the old gasket, which has a grooved fitting inside the front cover). The Torq Specs for the front cover (5 bolts) and water neck cover (2 bolts) is: 89 Inch Pounds. Those small bolts tighten normal, clockwise.

Read more: http://wiki.answers.com/Q/How_do_you_replace_the_water_pump_on_a_1999_Oldsmobile_Aurora#ixzz1CeLdWsjN

Jan 30, 2011 | 1998 Oldsmobile Aurora

1 Answer

Do i need a special tool for changing water pump on 95 crown victoria at home


depends on if it has a clutch fan or electric... if its electric the no you dont need any special tools but if its a clutch fan then you need a clutch fan removal tool

Jan 21, 2011 | 1995 Ford Crown Victoria

2 Answers

How hard is it to replace the water pump. 2006 chevy trailbalzer LT Time to do job?


1 hour if have done them before.If not 3 hours should do it.however you need a special tool to take off the fan clutch from the pump.Caution should be used as not to damage the radiator as it is a tight fit.

Dec 02, 2010 | 2006 Chevrolet Trailblazer

1 Answer

HOW DO YOU REMOVE A WATER PUMP FROM A 2006 CHEVY TRAILBLAZER WITH A 4.2 ENGINE


This will be a pain,but not really that hard.It's a matter of hand room.
The '06 uses a hydraulic fan clutch that you'll need a special tool to remove.Usually you can "borrow" one at Autozone.
I'm posting a link to a write up on removing the clutch assembly and pump.You'll have to register to view it though.
Bob
http://forums.trailvoy.com/showthread.php?t=19604&highlight=Fan+Clutch+101


Aug 10, 2010 | 2006 Chevrolet Trailblazer

Not finding what you are looking for?
2006 Hummer H3 Logo

545 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...