Question about 2000 Ford Windstar

1 Answer

Where is the screws location - 2000 Ford Windstar

Posted by on

1 Answer

Read your statement

Posted on Nov 29, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the rear bleeder screws located on my 2000 chevy tracker?


Remove wheel and you should find bleeder screw at the top of the caliper or wheel cylinder.

Feb 26, 2015 | 2000 Chevrolet Tracker

1 Answer

Nissan vanette idle screw location?


There is no idle ajustment screw, the idle speed is computer controlled.

Apr 11, 2012 | Cars & Trucks

1 Answer

Remove tail light on a 1998 el ford


To remove the tail lights screws can be located in 2 places on the outside of the vehicles there is 3 to 4 screws to be removed or 3 to 4 screws may be located on the inside or back of the light. Remove these screws and the tail light assembly should become free. Remove and replace with new tail light and tighten the screws back down and your done.

Nov 28, 2010 | Ford Futura Cars & Trucks

2 Answers

Does 1999 chevy malibu 4cylinder have transmission dipstick?


no, see below for level check procedure:

  1. Raise and safely support the vehicle.
  2. Place a container under the fluid level screw.
    0cc12f3.gif

Fig. The fluid level screw (see arrow) is located above the transaxle pan on the passenger side of the vehicle

  1. Remove the fluid level screw.
  2. Ensure the oil level is at the bottom of the level screw.

NOTE Because the transaxle operates correctly over a range of fluid levels, the fluid may or may not drain out of the screw hole after removing the screw. If the fluid drains through the screw hole the transaxle may have been overfilled. When the fluid stops draining the fluid level is correct, and you may install the level screw. If the fluid does not drain through the screw hole, the transaxle may have been low. Add fluid at the vent cap location in 1 pint ( 1 / 2 liter) increments until the oil level is at the bottom of the oil level hole. Use a long necked funnel to avoid spillage.

  1. Install the oil level screw and tighten to 124 inch lbs. (14 Nm).
  2. Lower the vehicle.
  3. Connect the negative battery cable.

Sep 29, 2010 | 1999 Chevrolet Malibu

1 Answer

The rear bumper to the caravan is it held on by Christmas Tree Clips Or Screws?


There are 2 screws located behind the rear wheel on both side. (Phillips screws)
There are also 2 screws located under the rear door.
And the bottom of the bumper is held on using push in plastic clips. Unless you want to purchase new clips I would suggest purchasing a door clip removal tool.
Once the screws and the 4 clips are removed from under the cover it will slide outwards from the rear.
Thanks, Dorrian

Jul 07, 2010 | 2005 Dodge Caravan

1 Answer

Oil filter location


The V6 has a screw on filter unlike the 4 cylinder which has a cartridge filter. The filter is located in one of 2 positions depending on which V6 you have. On one V6 it is located under the car towards the front where there is a splash guard that is held in place by two thumb screws. Remove the thumb screws take out the splash guard and there it is. On the other V6 it is located under the air tube that comes from the air filter where you will see a nut about the size 3/4 or bigger just unscrew it and change your oil filter.

May 01, 2010 | 2002 Pontiac Grand Am

2 Answers

Headlight adjustment


This is your second response. I am calling amchrisler for the screw location

Dec 20, 2009 | 2000 Dodge Caravan

1 Answer

LOCATION OF BLWER MOTOR


The blower motor is located under the dash on the passanger side 4 screws hold it in. Remove the screws then the motor will come down.

Oct 12, 2009 | 1995 Isuzu Pickup

1 Answer

Screw location on dash for 1998 pontaic grand am


Its 2 screws in the middle below the temp controls and 2 just above the speedometer.

Aug 16, 2008 | 1998 Pontiac Grand Am

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...