Question about 1996 Ford F250 Crew Cab

1 Answer

Ignition cylinder for 1988 ford f250

I need to know how to replace this item in my truck. I already have the part.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

Pull steering wheel then put key in igniton turn it to on position and you should see a hole in the bottom of column shove a pick in it to release cylinder

Posted on Nov 29, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: 93 Ford Ranger Ignition Cylinder

Hi..
On 1993 Ford ranger to remove the ignition lock cylinder switch

You need to remove the Steering wheel.
Remove trim shrounds.
Set ignition switch to Run position.
If your vehicle is A/T trans. put the selector lever in Park.
You will see retaining pin. Push retaining pin inward and pull out the lock cylinder.
Unplug wire from lock cylinder.
To install reverse remove procedure.

NOTE'' If you don't have the key or the cylinder is locked.
Instead of push the retaining pin you will need to Drill with a
1/8 in ( 3.17mm) Bit to drill out the retaining pin.
Be careful DO NOT drill more than 1/2 in deep.
After you need a chisel to break away the cylinder cap.
You need a 3/8in (9.52mm) bit to Drill in center of the cylinder.
Drill aprox. 1 3/4 in( 44mm) Deep.
REmove metal shavings. And remove the cylinder.
Clean and lubricate the gear inside. and install the new cylinder.

OK............I hope this information work for you.
Thank's for use fixya.

Posted on Jul 13, 2008

tripletauto
  • 1450 Answers

SOURCE: 1996 ford f250 4 wheel drive truck

Item Part Number Description 1 N800794-S60 Bolt, M16-2.0 x 50 2 N601797-S2 Bolt, Caliper Mount M12-1.75 x 30 3 2C150 Pin Assembly 4 2C357 Disc Brake Caliper 5 1175 Seal 6 3423 Bearing 7 3105 Front Wheel Spindle 8 4221 Differential Bearing 9 4222 Differential Bearing Cup 10 1190 Wheel Seal 11 1102 Front Disc Brake Hub and Rotor 12 1102 Front Disc Brake Hub and Rotor 13 1197 Locknut 14 1B198 Lockwasher 15 1C245 Thrust Washer 16 35704 Dana Nut 17 2K004 Front Disc Brake Rotor Shield 18 2B292 Anchor Bracket 19 3130,
3131 Steering Knuckle9572fc0.gif

Posted on Aug 19, 2008

  • 43 Answers

SOURCE: where is the horn on a ford f250?

Your horn on this vehicle is located on the rad support.

Posted on Apr 07, 2009

emissionwiz
  • 75822 Answers

SOURCE: locate fuel pump alternate switch and how to reset it.

the fuel pump cut off safety switch (inertia switch) is near the parkbrake pedal.there is a push button on top, push it to reset

Posted on Apr 10, 2009

  • 1 Answer

SOURCE: stuck ignition cylinder 1992 ford taurus

It is not necessary to have the dealer do this, think of the cash! Though it does require patience and time. The pin you are supposed to push in goes into a slot when you have it in run position, since you cannot turn it to run you have to make a slot for the pin to go into, with a drill. Be very careful as you only have a 1/4" of play before you break a washer behind the cylinder. Once you have drilled out the key far enough to the pin hole you can take a nail set and tap the pin up, you can tell when the pin clears the housing, then it just takes wiggle, patience and tinkering to get the cylinder to slide out, keep the green washer and the metal slot washer. Metal slot washer goes in first with green plastic washer ontop of that with lock cylinder in last. You can play around with the new lock cylinder and washer before insertion to determin correct direction.

Here are official directions with inoperable lock cylinder. They say drill out retaining pin but it just spun in circles for me - I looked at new cylinder and saw how it worked. retaining pin needs a place to go.
Removal & Installation (Non-Functional)
NOTE:Use this procedure to remove ignition lock cylinder if key is missing or cylinder is frozen.

Disconnect negative battery cable. Disable air bag system. See appropriate AIR BAG RESTRAINT SYSTEMS article in RESTRAINTS. Wait at least one minute for air bag back-up power supply to deplete. Remove steering wheel. See STEERING WHEEL . Using a 1/8" bit, drill out retaining pin located below lock cylinder on housing. DO NOT drill deeper than 1/2".
Using channel lock pliers, twist lock cylinder cap until it separates from lock cylinder. Using a 3/8" drill bit, drill down center of ignition lock key slot about 1 3/4" until lock cylinder breaks loose from its base.
Remove retainer, washer, and lock cylinder gear from housing. Remove metal shavings from lock cylinder bore. Replace housing if damaged. To install, reverse removal procedure. Connect negative battery cable. Check air bag system for proper system operation. See appropriate AIR BAG RESTRAINT SYSTEMS article in RESTRAINTS.

Posted on Jul 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

When i try to start my 1988 mustang gt. I have to hold the key over to keep it started if i let it go it shuts off?


it may need a little adjust in the ignition switch not the key cylinder but the electric switch it is located in the steering column under dash and is hold by two screws you will need a 5/16 wrench to loose these screws and push the switch a little to the front then tight the screws i hope this help you fix it i'll be happy to assist you if you have further questions please let me know if this was useful.

Mar 06, 2011 | 1988 Ford Mustang

1 Answer

I have a 1988 Ford F250 4x4 with a 4.9 straight 6 engine. It will run about 15 min's then just shut down. I will wait for about one hour for it to cool off then it starts up runs for about 15 min's then...


I would replace the distributor stator and the TFI ignition module both of which are in and on the distributor. Use Ford OEM parts (Motorcraft) as after market fail very quickly.

Mar 30, 2017 | 1988 Ford F 250

1 Answer

Would like to see brake digram of 1995 ford f-250


Item Part Number Description 1 2B120 Disc Brake Caliper 2 2140 Brake Master Cylinder 3 — Manifold Vacuum Source 4 2365 Power Brake Booster Check Valve 5 2005 Power Brake Booster 6 13480 Stoplight Switch 7 2455 Brake Pedal 8 — Fluid Level Indicator
(Part of 2L454) 9 11572 Ignition Switch 10 2261 Rear Wheel Cylinder 18fb197.gif

Mar 10, 2010 | 1995 Ford F250

1 Answer

I need to know how to time a 88 ford f250 with a 351w it dont have the wirers on the distribter


bring number one cylinder up on compression and wire the cap counter clockwise firing order 15436278 started from number on cap where rotor bug is with #1 on compression

Jan 17, 2010 | 1988 Ford F 250

1 Answer

1988 Ford F-150 ignition lock cylinder replacement when you lose the keys, anyone know a simple way to replace it when you don't have the keys?


No real simple way. Steering wheel removal is required and drilling out the retainer pin .
Taking out the cylinder from the outside is possible but damage to the steering column is a risk and lots of patience with a die grinder is needed.

Nov 05, 2009 | 1988 Ford F 150

1 Answer

My f250 5.0 is cranking but it will not fire!


Replace the TFI ignition module on the distributor and the distributor pickup sensor (AKA "Stator") inside the distributor.

Apr 28, 2009 | 1988 Ford F 250

1 Answer

I have a 1987 Ford F250 Lariat. Auxilary problems


not the cylender adj the ignition switch down on the steering colum

Apr 11, 2009 | 1989 Ford F 150

1 Answer

My ignition switch is broken


this is a common ford ignition cylinder problem.you can buy a new key cylinder at a checker or autozone cheap.remove column cover and push small metal button and cylinder comes out

Jan 17, 2009 | 2001 Ford F250 Super Duty Super Cab

1 Answer

92 F250 ignition tumbler can't remove


You need to remove the steering wheel and disassemble the steering column far enough to access the lock cylinder release tab from the inside. If you have already purchased a replacement cylinder, you can locate it quite easily.

Sep 27, 2008 | 1992 Ford F250

Not finding what you are looking for?
1996 Ford F250 Crew Cab Logo

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...