Question about 1993 Honda Accord

1 Answer

Replacement window glass for 1993 accord

Need to replace the glass for the stationary rear window on a 1993 accord got the glass but dont know the trick for putting it in.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 103 Answers

I have worked on cars for 10 years personally and 3 years professionally. I have found its worth it to have it done. The stationarys in your honda are sealed in with a calking compound and if not done right they break easy. Sorry I couldn't help more.

Posted on Jan 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Side stationary window 99 monte carlo need replacement instructional video


Check Youtube for a video. Auto glass replacement - that should dredge up some help. Removing the interior door panel and getting to the window-glass support takes the most time in my experience.

Jan 19, 2015 | Cars & Trucks

1 Answer

How do i remove a rear window


hard top or convertible.?
I guess at hard.
Not side rear. or doors., but rear rear. as in rear view.

rear window. glass out? why not say why so can see JOB ? at hand.
eg: my rear view glass is broken.?

is covered in the FSM, (like all cars made)
the factory service manual. or alldata.com (clone) log in read.

ok ill past the FSM words here.
Stationary Windows Stationary glass is removed and installed using the same procedure as the windshield. Refer to Windshield Glass Removal and Installation. (first hit ,btw)
https://www.youtube.com/watch?v=5dp2VVvPlXc
ever seen a front windshield changed out, sure.
same
best solution is......
Call the same company to come out and point to rear .?

they sell a special tool to get out a window.
it has 2 , "T" handles and rod saw. to cut out the glue/caulk.
the glue comes out more easy on a hot day.
its not really glass, it's an occupant containing device, today.
the best caulk is.
3M 08693 Auto Glass Urethane Windshield Adhesive Cartridge
how is my guess.... on car, and glass and reasons.

Dec 04, 2014 | 1992 Suzuki Swift

1 Answer

How to replace rear door window on 93 pathfinder


If you can see the edge of the glass (not stuck inside a rubber mould) then the glass will be glued to the body. The quickest and easiest way for you to get a water proof job without the mess is to have a windscreen shop fit it for you. Believe me you do not want the hassle.

Dec 12, 2013 | 1993 Nissan Pathfinder

1 Answer

My driver side rear window is broken its the stationary on the back door. How hard is it to replace?


Depends on the vehicle but I would recommend safelite or another auto glass specialist.

May 03, 2013 | Cars & Trucks

1 Answer

I have a 2002 Honda Accord EX 4-dr sedan. The front driver's side power window motor works (you can hear it), and the window will go down, but not back up. You can hear the motor when pushing the button...


Hi, the reason you hear the motor running but the window wont go back up is because the window regulator is bad. you will need to go to a parts store and get a replacement. you can get a replacement at Advance Auto Parts for $72.99. the part number is 741-766.

May 18, 2010 | Cars & Trucks

1 Answer

I have a 1990 Honda Accord EX and need to replace the driver and passenger windows. I am replacing them myself from a junkyard. Can I use other years besides 1990 to match up the window


Accords 1990 through 1993 should have the same glass, given the same body type, and given any differences in the mechanisms( power, not power, etc.). I would take a careful look, or even some digital camera pictures to compare when I went to the salvage yard. Better yet, take the old windows (or what is left of them).
Hope this is helpful.

Oct 26, 2009 | 1990 Honda Accord

1 Answer

How do I remove and install a rear passenger side window (manual) in a 1997 Saturn SL1?The window was smashed, and I need to replace it. Thank you so much for your time and help!


Saturn Coupes/Sedans/Wagons 1991-1998 Repair Guide
Door Glass and Regulator - REMOVAL & INSTALLATION
(see Figures 1, 2, 3 and 4)
  1. Remove the outer door panel assembly. Refer to the sub-procedure under Door Locks, earlier in this section.
  2. For rear doors, loosen the bottom fastener of the rear door stationary window assembly, in order to provide clearance, then apply tape to the lower half of the outboard exposed portion of the stationary window channel. The tape must be applied in order to prevent damage to the paint surface.
  3. Lower the door glass, then use SA9148B, or an equivalent tool, to remove the glass nuts. Push the glass upward and rotate slightly, then remove the glass from the vehicle.
  4. If the regulator is also to be removed, proceed as follows:
    1. Remove the inner door trim panel. Refer to the procedure earlier in this section.
    2. If applicable, unplug the wiring harness from the power regulator.
    3. Except for the rear door, remove the regulator cam bolts.
    4. Drill out the regulator rivets and remove the regulator from the vehicle.
To install:
  1. If removed, install the regulator to the door assembly:
    1. Position the regulator to the door and secure using rivets.
    2. Except for the rear door, install the cam bolts.
    3. If applicable, connect the wiring harness to the regulator.
    4. Install the inner door trim panel to the vehicle.
  2. Install the door glass into the door and over the regulator studs.
  3. Install the glass nuts using tool SA9148B, or equivalent.
  4. Check the door glass for proper operation and alignment.
  5. If necessary, adjust the glass alignment. For rear doors, fore/aft adjustments are made after loosening the B bolts, while in/out adjustments are made when the A bolts are loosened.
  6. Except for the rear doors, glass which is not running parallel to the door header may be adjusted after loosening the inner panel cam attachment bolts and adjusting the cam. If the glass is floating in the opening, lower the glass 3 / 4 downward, loosen the front guide fasteners, push the glass rearward to seat it in the rear channel, then bring the front glass guide back to the front edge of the glass. Apply a light finger pressure on the guide and tighten the fasteners.
  7. Once the glass has been properly adjusted and is operating smoothly, install the outer door panel assembly.
cc80642.jpg

Fig. 1: Remove the glass nuts using a suitable tool-front door shown

8ca6a10.jpg

Fig. 2: Exploded view of the regulator mounting-except rear door

b18d064.jpg

Fig. 3: Exploded view of the rear door regulator mounting

0b9470a.jpg

Fig. 4: Adjustments of rear door glass are made after loosening the A or B bolts


I hope help with this (remember rated this help) Good luck.


Oct 16, 2009 | 1997 Saturn SL

1 Answer

How do you replace a drivers side window on a 1992 Saturn



REMOVAL & INSTALLATION

See Figures 1, 2, 3 and 4
  1. Remove the outer door panel assembly. Refer to the sub-procedure under Door Locks, earlier in this section.
  2. For rear doors, loosen the bottom fastener of the rear door stationary window assembly, in order to provide clearance, then apply tape to the lower half of the outboard exposed portion of the stationary window channel. The tape must be applied in order to prevent damage to the paint surface.
  3. Lower the door glass, then use SA9148B, or an equivalent tool, to remove the glass nuts. Push the glass upward and rotate slightly, then remove the glass from the vehicle.
  4. If the regulator is also to be removed, proceed as follows:
    1. Remove the inner door trim panel. Refer to the procedure earlier in this section.
    2. If applicable, unplug the wiring harness from the power regulator.
    3. Except for the rear door, remove the regulator cam bolts.
    4. Drill out the regulator rivets and remove the regulator from the vehicle.


To install:
  1. If removed, install the regulator to the door assembly:
    1. Position the regulator to the door and secure using rivets.
    2. Except for the rear door, install the cam bolts.
    3. If applicable, connect the wiring harness to the regulator.
    4. Install the inner door trim panel to the vehicle.

  2. Install the door glass into the door and over the regulator studs.
  3. Install the glass nuts using tool SA9148B, or equivalent.
  4. Check the door glass for proper operation and alignment.
  5. If necessary, adjust the glass alignment. For rear doors, fore/aft adjustments are made after loosening the B bolts, while in/out adjustments are made when the A bolts are loosened.
  6. Except for the rear doors, glass which is not running parallel to the door header may be adjusted after loosening the inner panel cam attachment bolts and adjusting the cam. If the glass is floating in the opening, lower the glass 3 / 4 downward, loosen the front guide fasteners, push the glass rearward to seat it in the rear channel, then bring the front glass guide back to the front edge of the glass. Apply a light finger pressure on the guide and tighten the fasteners.
  7. Once the glass has been properly adjusted and is operating smoothly, install the outer door panel assembly.

PICTURES ON NEXT POST!

Oct 13, 2009 | 2000 Saturn Ls 4dr Sedan

2 Answers

The windows are missing the guides


Louis, go to site 'hondapartscheap' southbay honda, enter your honda info, they have great diagrams of body and engine parts, and prices aren't too bad either. Let me know if u have any trouble accessing info there.

Dec 31, 2008 | 1993 Honda Accord

4 Answers

Rear speaker size in my 1993 Honda Accord


I HAVE A 93 ACCORD LX AND ACCORDING TO HONDA MINDS COME WITH 6.5" SPEAKERS FOR THE BACK AND TO GET 6X9 IN YOUR GOING TO EITHER GET THE SPACER THE COME WITH THE EX OR YOU OR GOING TO HAVE TO CUT AND THEY DONT RECOMMAND IT CAUSE YOUR TRUNK WONT STAY OPEN AND YOUR GOING TO HAVE TO BEND THE BAR UNDER THE TRUNK. HOPE YHIS WAS HELPFUL.

Dec 16, 2008 | 1993 Honda Accord

Not finding what you are looking for?
1993 Honda Accord Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...