Question about 1993 Chevrolet S-10

1 Answer

How to install brake and tail light socket for 2000 chevy s 10 truck

I need to know how to change out the socket

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 129 Answers

Cut old harness out and pick up new pigtail from napa and solder wires for best connection

Posted on Nov 29, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 508 Answers

SOURCE: Star bit on front brake 2000 chevy 1500 ?

YES THEY COME IN METRIC SIZES. AND,MOST GM PRODUCTS ARE ALL METRIC THESE DAYS. GET A MERTIC SET. YOU WILL ALWAYS USE THEM AGAIN. TOOLS ARE A GOOD INVESTMENT.

Posted on Jan 24, 2009

  • 713 Answers

SOURCE: how do i replace tail light harness with socket in a cavalier 01

if you have a complete replacement harness it unplugs behind the felt in the trunk. if it is just a socket with a pigtail clip wires about an inch from old socket and use but splice connectors and use electrical tape to cover them back up with.

Posted on Aug 26, 2009

Testimonial: "thanks"

  • 14036 Answers

SOURCE: 1994 Chevy truck. Turn signals do not work.

CHECK FUSE.IF GOOD YOU HAVE A BAD GROUND OR FAULTY TURN SIGNAL FLASHER.FLASHERS LOCATED ON THE INTERIOR FUSE RELAY BOX.

Posted on Sep 22, 2009

  • 16 Answers

SOURCE: How to change rear brake disk on 01Chevy Silverado

need a torx 55. must remove caliper in the bracket then remove the caliper. Bracket bolts are 17mm I think.

Posted on Mar 24, 2010

  • 447 Answers

SOURCE: Brake light dont work. 2006 chevy truck, 4.8L 2wd

Some of these had two fuses for brake lights. One for the top/center stop lamp and another for the rear left and right brake lights. Usually one said "stop" and the other said "brake" and one was in the underhood panel while the other was in the dash fuse panel. It's not uncommon to blow a brake light fuse [LR and RR] if you tow a trailer but some of these had seperate fuses for the trailer lights also. If you have a test light check both sides of the two fuses for power [ignition key on] while stepping on the brakes. It should at lest narrow your search a bit.

Posted on Jun 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the tail light fuse?


The tail light fuse is under the rear seat on the drivers side.

Jan 17, 2016 | 2003 GMC Envoy

2 Answers

The tail light sockets have 3 wires. white, brown, and black. I know black is ground. which wire is brake and turn?


I know the color code for chevy and the brown lead is for the running lights,soooo the white wire would be for the brake and turn sig.

Dec 30, 2010 | 1988 Chevrolet K1500

1 Answer

How to change break lights


Tail Lights
  1. Open the endgate or liftgate.

  2. Remove the screws that retain the tail lamp assembly to the vehicle.
    32085_blaz_g0151.gif

    Tail lamp assembly removal

  3. Rotate the bulb sockets 1/4turn counter-clockwise in order to remove the bulb sockets from the tail lamp assembly.

  4. Remove the bulbs from the sockets.

To install:

  1. Install the bulbs into the sockets.

  2. Install the bulb sockets to the tail lamp assembly by rotating the sockets1/4 turn clockwise.

  3. Install the tail lamp assembly to the vehicle.

  4. Install the screws that retain the tail lamp assembly to the vehicle. Tighten the screws to 17 inch lbs. (1.9 Nm).

Oct 23, 2010 | 2000 Oldsmobile Bravada

1 Answer

My brake lights do not come on when i press the brakes. i have changed the switch for the brake lights but I still get nothing, which wire do I need to change because the brake light wire on my 2000 Esteem...


If you have a meter.... check the bulb socket for 12V DC with someone applying the brake or watch for a 12V DC pulse on the meter when the meter leads are on the socket contact with the emergency flashers on. (+) lead to socket contact and ( - ) lead to chassis ground. If you have the 12V DC on the socket contact then there is a problem with the chassis ground wire.
The brake light socket has 2 terminals. One is for the tail light 12V DC power when the headlights are on and the other one is 12V DC only when the brake lights are supposed to be on. (i.e pulse hazard or brake applied light on)

Also check the BRAKE light fuse in the fuse box located on the front of the left kick panel wall drivers side with a black cover. (4" x 2.5") There is also a fuse and relay box on the left side of the engine compartment. (4" x 7")

The wire color connected to your NEW brake switch that leaves the switch for the tail lights is the same color on the rear of the car and terminates at the tail light assy quick disconnect connector.

Thanks for using FixYa.

Kelly

Apr 23, 2010 | 2000 Suzuki Esteem

1 Answer

2001 chevy S10 brake is applied the right tail light goes out


you have a bad ground. go to that light bulb socket and check for ground to the socket.

Mar 07, 2010 | 2001 Chevrolet S-10

2 Answers

Need a wiring diagram for a chevy s10. brake


your power starts at the brake light fuse,check with a test light,then proceed to stop light switch on brake pedal under dash,one wire will be hot when when you check it with your test light, the other won't be until you press down the brake pedal then the power flows through to the second wire,if no power to second wire replace switch,if you have power remove tail light bulbs and check for power in side socket.

Nov 24, 2009 | 1997 Chevrolet S-10 Pickup

1 Answer

2000 chevy 3/4 ton diesel no brale light but third brake light wo


I just Know that you replaced the bulb ,try a test lite ,make shure it's grounded well poke inside the socket for the bulb this metal socket gives the bulb both electric and a ground ,this is the problem,good luck.

Nov 14, 2009 | 2000 Chevrolet 2500

1 Answer

Brake light problem


My van did the same thing it was the ground at the socket it had a good ground all the way to the socket but lost it right at the socket.

May 14, 2009 | 2000 Chevrolet Express Cargo

2 Answers

Chevy S10 Tail Light issue


CHEVY S-10 TAIL LIGHTS PROBLEM RESOLVED...It seems Chevy engineered a ground shorting clip located under the left rear bumper area. It looks like a connector for trailer wiring harness, but in actuallity is a metal shorting clip which ties 5 wires together. They are all the ground wires for the tail lights. Then one single small wire runs to ground completeing the circuit. Problem is that this one wire is not tough enough to be a strain relief for the grounding plug and over time the ground wire wears, leaving intermittent lighting problems. FIX IS TO SPLICE THE GROUND WIRE INTO ONE OF THE FIVE OTHER WIRES AND USE PLASTIC TY WRAP FOR STRAIN RELIEF. This fixes no tail lights, intermittent rear signals, and other significant problems. I just got done making this same repair on a 2000 s-10 and everything works fine. Since it is the strain on the single ground wire connected to the connector that leads to failure, it is best to tie a new ground or clip the ground wire coming out of the plug and resplice it into one of the other five wires. Does not matter which one since electrically it makes no difference; they are all gound wires. BUT only one wire completes the connection and that is the problem. Really good engineering Chevy! The location is under left rear of bed in wiring harness right before the split. The connector is blue or green. Take the cover off to see the metal shorting clip. Also note the ground wire coming out of the plug/connector and runs about 8 inches to frame. If this is not hooked up you will have tail light issues. If you register on Autozone .com you can access wiring schematics for free. BL

Dec 15, 2008 | 1993 Chevrolet S-10

Not finding what you are looking for?
1993 Chevrolet S-10 Logo

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...