Question about 1997 Chevrolet S-10 Pickup

1 Answer

Where are the freeze plugs on 1997 chevy s10 pickup

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 22,095 Answers

In the cylinder block and the cylinder head ,dont forget the one behind the flywheel

Posted on Nov 29, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: How to replace rear freeze plug

I have the same truck leaking at back not positive its the freeze plug any ideas?

Posted on Feb 04, 2010

  • 35 Answers

SOURCE: The reverse ligths on my mom's S-10 pick up won't come on.

I'm guessing you checked the bulbs. test the reverse light switch. Should be found on the drivers side of the transmission. Should have power leaving it when the truck is in reverse.

Posted on Mar 21, 2009

  • 1596 Answers

SOURCE: I need to replace the fuel pump in my 1985 Chevy S10 Pickup.

EXACT PROCEDURE ! Please Rate Me Fairly for this!! Thank you And Good Luck !!


ELECTRIC PUMP

REMOVAL

  1. Before servicing the fuel pump the fuel system pressure must be relieved. See: Fuel Pressure Release
  2. Disconnect the negative battery cable.
  3. Raise the car on a hoist.
  4. Remove the fuel tank. See Fuel Tank / Service and Repair.
  5. Remove the fuel tank sending unit and pump assembly by turning the cam lock ring counterclockwise. Lift assembly from the fuel tank.
  6. Pull the fuel pump up into the attaching hose while pulling outward away from the bottom support. Take care to prevent damage to the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull the pump assembly out of the rubber connector for removal. NOTE: Inspect the fuel pump attaching hose for any signs of deterioration. Also check the rubber sound insulator at the bottom of the pump. Replace damaged or deteriorated parts.
INSTALLATION
  1. Push the fuel pump assembly into the attaching hose.
  2. Position the fuel tank sending unit and pump assembly into the fuel tank. Use a new "O" ring seal. NOTE: Care should be taken not to fold over or twist the strainer when installing the sending unit as this will restrict the flow of fuel. Also, verify that the strainer does not block the full travel of the float arm.
  3. Install cam lock over the assembly and lock by turning clockwise.
  4. Reinstall fuel tank.
MECHANICAL PUMP

REMOVAL and INSTALLATION

NOTE: To ease pump installation, rotate the camshaft so the camshaft eccentric is out of the way of the fuel pump rocker arm.

  1. Disconnect fuel lines from fuel pump.
  2. Remove fuel pump mounting bolts and the fuel pump.
  3. Remove all gasket material from the pump and block gasket surfaces. Apply sealer to both sides of new gasket.
  4. Position gasket on pump flange and hold pump in position against its mounting surface. Make sure rocker arm is riding on camshaft eccentric.
  5. Press pump tight against its mounting. Install retaining screws and tighten them alternately.
  6. Connect fuel lines. Then operate engine and check for leaks.

Posted on Mar 22, 2009

  • 1 Answer

SOURCE: Chevy S10 Pickup Starter. Removed the two bolts

Just changed a starter in a 94 S10 4x4. The only way to remove the starter was to take the passenger side exhaust manifold off and bring the starter out that way. Installation the same in reverse. Hope this helps. Don

Posted on Jun 25, 2009

  • 740 Answers

SOURCE: 1997 Chevy S10 pickup Fan switch for heater runs on high only.

replace the blower motor resistor located on the heater box were the blower motor is located the wiring to the blower may go to it. This is very easy to locate if you buy the part first.

Posted on Jan 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of freeze plugs on 99 Chevy s10 4.3 liter


it is under your manifold driver side remove wheel well and tire to get to it!

Sep 01, 2014 | 1999 Chevrolet S-10 Pickup

1 Answer

1997 chevy s10 pickup antifreeze leak, need help.


Check your intake, sometimes water runs thru the intake to cool it down and it can crack on the inside. When this happens it will send water to cylinders where it is burned. Also, any leaks at the water pump?

Mar 27, 2013 | 1998 Chevrolet S-10 Pickup

1 Answer

1997 Chevy S10 pickup Fan switch for heater runs on high only.


replace the blower motor resistor located on the heater box were the blower motor is located the wiring to the blower may go to it. This is very easy to locate if you buy the part first.

Jan 06, 2010 | 1997 Chevrolet S-10 Pickup

1 Answer

Where can i find the plug from my block heater in my 1997 chevs10


not all s-10 came with a block heater. the plug is on the end of a long extension cable, should be on either side of the block. if you can't find it, it most likely doesn't have one. you can install one, just by the kit from your local GM parts department, raise the vehicle in the air, remove a freeze plug & install the block heater where the freeze plug was.
its not an easy job.

Dec 31, 2009 | 1997 Chevrolet S-10 Pickup

1 Answer

1997 Chevy S10 A/C not cooling. Fan blows


sounds like the airbox doors are not working these are located behind the dash passengers side, a chiltons manual availible at most parts stores for around $25 will give you diagrams and steps to access this area if u need that help

Jul 08, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Loss water


head gasket bubbels comming up on radiator ?

Mar 01, 2009 | 1997 Chevrolet S-10 Pickup

2 Answers

No tail lights


Try checking the headlight switch it may have broken contacts in it. Easy fix go to a salvage yard find same make and model truck, swap headlight switches.

Dec 27, 2008 | 1997 Chevrolet S-10 Pickup

Not finding what you are looking for?
1997 Chevrolet S-10 Pickup Logo

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...