Question about Cars & Trucks

1 Answer

I have a 1982 honda goldwing A and I need to know what is the part called that the the starter fits into on the fly wheel that needs replacing it is worn out and it keeps free spinning it is not the s

It is the part that fits between the fly wheel and the starter,

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 318 Answers

You are refering to the teeth part known as the ring gear. It usually wears in 2 places ad in te old days we used to heat the ring up to release from flywheel and turn it 90 Deg and let cool and refit. Just as easy to get new flywheel these days

Posted on Nov 29, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 625 Answers

SOURCE: 2004 Mercury Mountaineer Problem...wont turn over

just be liitle more specificc please do you hear any noise when you try to start it? like a click or something?

Posted on Jun 10, 2008

CRTN
  • 716 Answers

SOURCE: Ford F150 starter does not engage, spins the catches off and on

Most Likely The Starter I Know We Changed It Is What your Thinking.
I Done 3 In A Row And The Fourth One Was Finally Good.

Posted on Jan 21, 2009

  • 84 Answers

SOURCE: Need diagram/detailed advice on how to replace rear wheel bearing

Go to autozone.com enter your car info in. go the repaor section and it will be there.

Posted on Mar 22, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic

Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

Posted on May 23, 2009

ZJLimited
  • 17970 Answers

SOURCE: Replace a starter

1999 Honda Civic DX 1.6L MFI SOHC 4cyl
Starter Removal & Installation

c4ae816.gif

Fig. Starter wire connections

304d19e.gif

Fig. A ratchet and long extension may be needed to remove the starter

The factory sound system has a coded theft protection system. It is recommended that you know your reset code before you begin.

  1. Disconnect the negative battery cable.
  2. Remove all wiring from harness.
  3. Remove the lower radiator hose from the bracket on the starter motor.
  4. Remove the starter cable from terminal B located on the back of the solenoid.
  5. Remove the black/white wire from the S (solenoid) terminal.
  6. Remove the two bolts that mount the starter to the transaxle assembly.
  7. Remove the starter.

To install:
  1. Install in the reverse order of removal.
When installing the heavy gauge starter cable, make sure the crimped side of the terminal end is facing out.
  1. Enter the anti-theft code and radio presets.

I hope help you with this (rated this help). Good luck.

Posted on Sep 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1992 subaru legacy starter wont engage fully and makes a loud grinding noise


Sounds like it is not toughing 100% and making full gear contact with the fly-wheel. Replace starter or the misalignment can burr the flywheel causing rounding and subsequent damage to the device.

May 09, 2014 | 1992 Subaru Legacy

2 Answers

My stater is free,spinning thn grindingmon the stop but it doesnt do it all the ti,me but is slowly getting worste its a 2001 z3 roadster 3.0im i replaced the crank positioning sensor but did nothing...


replace the starter and the flywheel-the bad starter has not engaged the teeth on the flywheel fully and has ground some teeth off so you'll fit that space every once in a while-cheers Denny

Oct 31, 2013 | 1999 BMW Z3

1 Answer

Flywheel or something grings against the starter when clutch is engaged


There is no way the ring gear will hit the starter pinion unless the fly wheel bolts on the crank shaft or loose allowing the flywheel to run out of true. If you have had clutch/ rear seal work done lately the fly wheel will only fit in one position and if that was ignored at some time then the fly wheel will run out and touch the starter pinion.. I would also check the adjustment on the starter pinion as it has to be set by the lever pivot to a correct distance or it will touch the teeth of the ring gear

Jul 28, 2013 | 2001 Ford Escort ZX2

1 Answer

I own a1989 Lincoln vii lsc and I need to know where the starter is located and how much a replace one. rebuilt


STARTER UNDERNEATH CAR LOOK WHERE FLYWHEEL LOCATED YOU WILL SEE STARTER AT FLY WHEEL COVER. STARTERS CAN COST FROM $100.00 OR LITTLE MORE.BUT CALL AROUND GET A PRICE CHECK.

May 18, 2011 | Lincoln Mark VII Cars & Trucks

2 Answers

Engine does not turn over when you turn key sounds like metal on metal grind....sounds like flywheel is jammed


The starter is bad, the drive that extends out to engage the flywheel has failed. If this has been going on for a long time, there's a chance the teeth on the flywheel are damaged, this should be checked when the starter is replaced.

Apr 22, 2011 | 1999 Honda Passport

2 Answers

INSTALLED NEW STARTER , SOUNDS LIKE ITS NOT FULLY ENGAGING FLYWHEEL


if the starter is making grinding sound it not! however it could be loos and needs to be bolted up tight or there may be a bad power joint to the starter,, check for this also check all the earth leads off the engine to the battery, if its still grinding then its likely to be a dud starter you fitted,, the solenoid is not fully engaging the starter bog in the fly wheel teeth and it stopping short and then it spins up this is whats making the grinding noise, it can also make a right mess of your fly wheel ring gear,, so dont leave it to long to get it sorted out,

Mar 02, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

Cost to replace starter & flywheel on a 2003


for the starter and flywheel 1400 sounds right they would have to take the tranny out to get to the fly wheel but why do they need to replace the fly wheel did your old starter do a lot of grinding its not to often you have to replace a flywheel unless the starter wrecked it somehow again not to often starters are ment to break before it wrecks the flywheel the flywheel made of harder metel i would get a second opinion on replacing the flywheel

Aug 27, 2009 | 2003 Ford Taurus

2 Answers

Car starts but sometimes makes a whirling noise. I was told it was the starter


sounds like the starter is not disengaging the fly wheel quickly like it should when you turn the key the starter cog connects upto a fly wheel that has teeth all around it when the teeth of starter cog connect between teen on wheel it spins it to crank your car then goes back to starter if you hold your key on after starting the noise you hear is the starter cog(teeth ) still engaged in wheel if this is the sound it needs to be serviced not neccassarily replaced

Jun 06, 2009 | 2003 Chevrolet Impala

1 Answer

1984 Cadillac Deville Ddiesel


You need to pull the starter out and check the drive gear. If the drive gear is no good you will have to replace the starter. Make sure the cogs on the fly wheel are okay. If the fly wheel is damaged you will have to replace the fly wheel.

Apr 25, 2009 | 1984 Cadillac DeVille

2 Answers

98 Chrysler Sebring 2.5 6cyl wont start. engine wont even turn


sounds like your starter ruined your flywheel. replacing the flywheel is not easy. also expensive. call a couple of tranny shops to get an estimate.

Mar 24, 2009 | 1998 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...