Question about 2004 Hyundai Elantra

1 Answer

How do you get rotor off 2003 hyundia elantra

How do you get the rotor off a 2003 hyundia elantra

Posted by on

  • 2 more comments 
  • Anonymous Mar 13, 2014

    the clutch is a hyundia elantra 2003 will not unengage.

  • Anonymous Mar 14, 2014

    2005 hyundia elantra reverse indicator plug

  • Anonymous Mar 14, 2014

    Can't remove dash ashtray in Hyundia Elantra Touring

  • Anonymous Mar 16, 2014

    install rear passenger wheel berring on a 2002 hyundia elantra

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 566 Answers

Hi from uk not sure if same as uk hyundai's but here goes ? if you remove wheel do you see two countersunk posi screws between studs that appear to hold rotor ?? if so then you will have to first remove the brake caliper assy by unbolting from the rear of caliper two 13 mm spanner/socket ? then you remove the two bolts that secure the carrier that the caliper bolts to 17 mm spanner/socket now you can remove the two contersunk screws then you may have to tap the rotor off the hub from rearuse a wire brush to clean up/away all rust/dust from caliper and carrier assys b4 refitting (take precautions from breathing dust) i assume you are fitting new pads ?? reassemble carrier then b4 fitting pads smear a light coating of copper grease on the rear of pad (metal side ) this prevents squealing on brakes then fully reassemble then b4 fitting wheel? bleed the brakee caliper a couple of pumps should expel dirty fluid then fit wheel carry out same proceedure on other brake assy as above fully then b4 you move car pump brake to ensure pedal is firm you will find that bleeding brakes will make pedal firmer as the old fluid becomes compressable due to heat/moisture absorbsion over time and heat from brakes is transferred to fluid via caliper piston understand?? that is why alway policy to bleed/flush brake fluid at least two yr interval this reduces spongy brake pedal hope this is all clear 4 you to follow best wishes for new year and hope you update on how you go on??

Posted on Jan 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I remove front rotors from a 2003 hyundai elantra


First jack the front end up. Then remove the wheels. Then remove the calipers. Then the rotors should fall right off the car into your hands. They are not pressed on or hubs

Jul 16, 2010 | Hyundai Motor 2003 Elantra

1 Answer

I want to change the front rotors on a 2003 elantra and what do I need?


mcdevito75 here, You"ll need a sturdy jack to lift the car, you"ll need the tools to lift the brake calipers off the rotor, in short let your local shop change the rotors. If you try and get stuck some how now you have to tow the car and have the rotors replaced.

Jun 17, 2010 | Hyundai Motor 2003 Elantra

1 Answer

The heater works great, however, you can't direct the air


The possible causes you describe are many... Take/tow the vehicle into a Hyundai Service Center (dealership), pay the diagnostic fee. They will tell you EXACTLY what the problem is and what's needed to fix it (parts, labor, tax, time-frame, etc.).

Jun 12, 2009 | 2000 Hyundai Elantra

1 Answer

Im looking for a hyundia elantra wind mirror


Go to a Hyundai Parts Store -- you'll find one there, but you'll have to pay for it.

Jun 11, 2009 | Hyundai Motor 2003 Elantra

1 Answer

Taillights for 2001 hyundia elantra


its real easy open trunk lid take rear sill off should just pop off then take trim panels each side then there are 4 bolts each side 10mm tkae bolts out firmly pull on tail lights they should come out and then reverse back

Jan 26, 2009 | 2001 Hyundai Elantra

1 Answer

Replacing studs


sometimes they just get stuck, which a big soft blunt hammer will cure with a good hit , or maybe you missed these assembly line screws ? there may be 2 of them on each rotor .

cd37a74.jpg

if there just stuck , try some penetrating oil / spray , and spray around the inside circle where the rotor meets the hub , let it penetrate ,give it a good smack with a hammer and a piece of wood so you don't damage the rotor .

Jan 10, 2009 | 2004 Hyundai Elantra

1 Answer

2003 hyundia sonata made before 2/2003


you should be able to get replacement parts at Napa or Oreillys they a fairly in expensive. but only if the are the drive in kind, meaning you need to take a hammer to knock them out of the rotor assembly then you just take a drift pin/punch and hammer them back in. hope this is helpful. please rate this solution. thanks

Aug 30, 2008 | Hyundai Motor 2003 Sonata

Not finding what you are looking for?
2004 Hyundai Elantra Logo

475 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...