Question about 2004 Dodge Intrepid

Open Question

2004 dodge intrepid 3.5 v6 fault code p0138

Fault code p0138

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 137 Answers

SOURCE: what does codes p0645 and p0481 mean on a 2004 dodge intrepid?

P0645 A/C Clutch relay circuit

P0481 high speed fan control relay circuit

Posted on Jan 19, 2009

  • 335 Answers

SOURCE: code p0138 for the second time

P0138 is code for o2 sensor Bank 1 Sensor 2. This sensor is the one behind the cat on the side of the engine that contains cylinder No 1.

Posted on Jun 15, 2009

  • 12 Answers

SOURCE: what does the code P0420 means in a 2004 dodge

A code P0420 may mean that the O2 (oxygen sensor) has gone bad and needs to be replaced. This is not detrimental to the operation of your vehicle but could make you fail an emissions inspection if your state requires them

Posted on Aug 03, 2009

  • 115 Answers

SOURCE: i have a 2004 dodge caravan i get p0172 fault code

p0172 fuel system to rich , p2097 fuel mixture high downstream , p0480 cooling fan relay, hope this helps

Posted on Aug 28, 2009

  • 608 Answers

SOURCE: My 2004 dodge intrepid is overheating how to git

Remove the top hose, unbolt the thermostat housing, remove old themostat and install new unit with new gasket. Replace top hose and fill with coolant. Be sure to re-check the coolant level after start up, beore you drive it anywhere, to eliminate any air pockets in the coolant.

Posted on Mar 22, 2010

Testimonial: "Thanks for the information it did help"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

2 Answers

03 dodge intrepid code p0138 O2 (B1 S2) Circuit Short to Voltage


What's Md mean ??
Not sure what the situation is here, but the code 138 is for the bank one O2 sensor after the catalytic converter. The computer says that sensor is not giving a reading that is acceptable.
Could be the sensor, or something going on with the engine.
A mechanic would use a scanner to "see" the sensor in action and determine if it is working or not.
It should not keep the car from running, but driving it for an extended period of time could cook the cat converter which would be an expensive repair.
This code should not have anything to do with the gas tank.

Jul 03, 2012 | 2003 Dodge Intrepid

1 Answer

I have p0743 p0138 p1763 and 1763 codes on 1998 dodge dakota v6 3.9 loss power


p0743-? p0138-oxygen sensor input voltage maintained above the normal operating range. p1763- governor pressure sensor volts too hi.

Nov 05, 2011 | 1998 Dodge Dakota

1 Answer

Trouble Code P0871


Hello Paul, The P0871 code on your Intrepid is a fault code relating to the overdrive pressure sensor circuit. The most common fix is replacing the solenoid pack in the transmission. I hope this information was helpful.

10_8_2011_7_40_21_pm.jpg

Oct 08, 2011 | 2004 Dodge Intrepid

1 Answer

I recently changed the engine of my Chrysler Intrepid 2001 2.7 V6 with a Chrysler Intrepid 2003 2.7 V6 engine. The engine runs fine except that the 2001 engine had an EGR sensor but the 2003 does not ....


you can talk to someone a the dealer(service manager/tech)to see if they can reprogram the pcm so it recognizes there is no egr on this motor

Sep 08, 2011 | 2001 Dodge Intrepid

1 Answer

Need torgue specs & sequence for upper & lower


Lower: Torque to 28 N·m (250 in. lbs.)

Upper: Torque to 12 N·m (105 in. lbs.)

Sequences below:

mf_grimm_1.jpg

mf_grimm_2.jpg

Good luck.

Jul 23, 2011 | 2004 Dodge Intrepid

1 Answer

Whats the code p0700 on a 04 dodge intrepid


Hi

P 0700 is basically a "generic" code signifying that the Transmission Control Module has detected a fault somewhere within the transmission's electrical system (typically a shift solenoid malfunction). If you see P 0700, take your car to some place that can plug a scan tool into it and retrieve the other codes which are causing your car to display the P 0700 code.

Jan 04, 2011 | 2004 Dodge Intrepid

1 Answer

WHAT IS CODE P0700 FOR A 2004 DODGE INTREPID


P 0700 is basically a "generic" code signifying that the Transmission Control Module has detected a fault somewhere within the transmission's electrical system (typically a shift solenoid malfunction). If you see P 0700, take your car to some place that can plug a scan tool into it and retrieve the other codes which are causing your car to display the P 0700 code.

Sep 12, 2010 | 2004 Dodge Intrepid

1 Answer

1996 Intrepid: firing order for 3.5 1996 dodge intrepid...


For the 1996 Dodge Intrepid 3.5L SOHC V6

Firing Order:
1-2-3-4-5-6

Cylinders:
......(back)
1........3........5
2........4........6
.....(front)

Ignition Coil Connections:
(back)
6....3
4....1
2....5
(front)

Let me know if this helped, or if you have additional informtion or questions. Feel Free to contact me at FixYa.com!

May 18, 2010 | 1996 Dodge Intrepid

1 Answer

Not running properly


Hi
code P0068 = MAF/MAP sensorthrottle position correlation
code P0108 = MAP/BARO circuit high input
code P0441 = EVAP emission control system purge flow fault
take it infor a service
cheers Rob.

Jul 20, 2009 | 2003 Dodge Intrepid

Not finding what you are looking for?
2004 Dodge Intrepid Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...