Question about 2002 Ford Explorer

Open Question

Location of egr valve on 1997 ford explorer 4.0sohc

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 92 Answers

SOURCE: 1998 Ford Explorer sport 4.0L 4x2 PCV Valve Location

the pcv is located on the rear(firewall) of the drivers side valve cover.turn counterclockwise and pull to remove be careful there are 2 small tabs inside the pcv hole in the valve cover(can feel with small finger) this is to hold valve in place so it wont leak.if you have a oil leak at the pcv a quick fix is to put a small amount of silicone around the pcv o-ring and install.wait hours for silicone to set up.

Posted on Oct 21, 2008

Ad
  • 61 Answers

SOURCE: I changed EGR valves, selinoid, sensors, and even

go to auto zone or someone with a scan tool to find out what codes are stored on the computer in the car

Posted on Jul 30, 2009

c17hydro
  • 2984 Answers

SOURCE: location of EGR valve for 4.6 liter engine

a887903.gif
EGR VALVE IS #2.

Please wait for second post to answer your second question....comes with a few pictures.

Posted on Nov 16, 2009

Testimonial: "thanks c17hydro ...looks like the proper proceedure,,,will try fix tomorrow"

  • 202 Answers

SOURCE: 1997 ford explorer check engine lite is on.Code

you probably have blocked passages in the intake manifold. remove the egr and check the port for a clog. you can scrape most of the carbon out with a pick or screw driver and then use some spray carbon cleaner in there. also check the metal exhaust line to the egr

Posted on Nov 17, 2009

Testimonial: "i looked at what was discribed and that wasnt it.Good thought thouh"

  • 1 Answer

SOURCE: EGR VALVE ON 96 FORD PROBE SE

If it's a 2.0L, 5 speed (1994-7) there are two DPFE solenoids (both w/ 3 vacuum ports) near the oil filter, which control the EGR valve. They are discontinued and impossible to find except on junked cars. (FORD #'s K5T44093-4)
I have to junk my 1996 Probe if I don't find them - Missouri emissions.

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Why is my truck idling rough but doesnt do it all the time


check throttle cable. A bad throttle cable will cause it accelerate
& decelerate. Check for worn out cable and replace it.

Jun 13, 2014 | 2000 Ford Explorer

1 Answer

EGR SYSTEM PROBLEM ON 1999 EXPLORER


sounds like a job for a Chilton's guide..

Jun 04, 2008 | 1999 Ford Explorer

1 Answer

Ford Explorer : How to Troubleshoot the EGR P0401 Trouble Code


P0401 - Exhaust Gas Recirculation Flow Insufficient Detected

Possible Causes:
- Harness or connectors (EGR volume control valve circuit is open or shorted.)
- EGR volume control valve stuck closed
- EGR volume control solenoid valve
- Dead (Weak) battery
- EGR passage clogged
- Exhaust gas leaks
- Faulty EGR valve

Possible Solutions:
- Clean EGR Valve
- Replace EGR Valve
- Repair EGR harness or connector
- Replace EGR volume control solenoid valve
- Replace EGR volume control valve

Jan 24, 2011 | Ford Explorer Cars & Trucks

1 Answer

I need a list of all emission control devices on a 96 ford explorer for a paper im writing for my apprenticeship


1996 Ford Explorer 2WD 5.0L


Canister Purge Valve
Catalytic Converter

EGR Position Sensor

EGR Vacuum Solenoid

EGR Valve

EGR Valve Gasket

EGR Valve Pressure Sensor

Exhaust Manifold

Exhaust Manifold Gasket

Fuel Cap

Muffler - Performance

Oxygen Sensor

PCV Valve

Sensor - Ambient Air Temperature

Smog Pump

Jan 15, 2011 | 1996 Ford Explorer

1 Answer

1997 Ford Explorer XLT V8 5.0L Check engine


ok you can take the egr valve off and clean it and if that works you my need to take it to get reset on codes other then that also check vacum lines if these do not work you will have to replace and i hate saying that because this part is high.. good luck to you and have a blessed day..

May 13, 2010 | 1997 Ford Explorer AWD

2 Answers

1997 ford explorer check engine lite is on.Code says low pressure in egr but ive replaced the egr valve and egr pressure sensor no luck


you probably have blocked passages in the intake manifold. remove the egr and check the port for a clog. you can scrape most of the carbon out with a pick or screw driver and then use some spray carbon cleaner in there. also check the metal exhaust line to the egr

Nov 17, 2009 | 1997 Ford Explorer AWD

1 Answer

What tool/how do you remove tube from egr valve on 2002 ford explorer v6? I have tried std 1 1/16" wrench, but there is no room to move given the location of the egr valve/tube. Is there a specialty tool...


The only other thing you may be able to try is using an adjustable wrench with a shorter handle, these are a pain to get to no matter what you do, but sometimes the adjustable wrench trick will work. Hope this helps

Jul 12, 2009 | 2002 Ford Explorer

3 Answers

1997 pontiac grand prix se has code po401. I


Check for

vacuum leaks on intake manifold,

the air tube between the air filter.

intake manifold vacuum hose.

===
clean throttle plate with Berryman carburator cleaner

SEE sample picture HERE
===

Also remove carbon built up behind the EGR valve and the EGR passage tube.

===

Vacuum leak WILL offset the intended 14.7 to 1 air fuel ratio.

More un-metered air (leaks) will lean out the fuel mixture.

Use small amount of Berryman carb clearer at potential air leak area will help you identify trouble spot.

At idle,just spray and listen for the RPM surge.

The in-rush of carb clearer will increase the RPM on the motor.

Record the problem spot(s) and address it later.

===

EGR carbon built up require 2+ hours to clean from start to finish.

You will need a new EGR base gasket before your start.

Locate and remove the EGR valve after the vehicle is cool down.

Carefully record the connector and vacuum line (for older vehicle) location by drawing an easily to follow diagram.

Remove the EGR valve.

Inspect the location of the carbon built-up inside the valve and the EGR passage tube.

SOAK these areas with WD-40 spary.

You will need a small screwdriver,cloth hanger and lot of newspaper and time to get this cleaning done right.

RE-SOAK the carbon and let it sit for over-night will also help.

One the last round,pass a shop vacuum of the EGR valve and the passage pipe.

Install the new EGR gasket and connectors.

Allow the vehicle to warm up outdoor to burn up any remaining WD-40.


Take it for a test drive.


Please rate my answer if it's useful to you.


Cheers,

Mustgo

Jun 30, 2009 | 2002 Ford Explorer

1 Answer

No vacuum to egr valve


there is an EGR vacuum solenoid somwhere that controls on/off vacuum to actuate the valve. i am not to sure of the location, but follow the vacuum line back from the egr until you find a device that looks like an electrical check valve for vacuum. that is a possibilty. but then again i am a ford,chrysler guy and am just giving you an answer based on my understanding of the functuality of a vacuum egr system

Jan 15, 2009 | 1997 Nissan Pickup

Not finding what you are looking for?
2002 Ford Explorer Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...