Question about 2001 Audi A6

Open Question

02 audi has a flashing brake light and brake code 01119

Snap on scanner said gear recognition signal intermillant

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22095 Answers

SOURCE: Audi A6 RPM Signal from ECU

dont think you are reading the codes right because PO in front of the code is not a genuine Audi code ,well not according to my information ,try autozone who issue these codes or a snap on code reader booklet

Posted on Dec 26, 2009

j_del
  • 1586 Answers

SOURCE: my 2001 audi tt quattro show in code scanner 02

Yes, sensor 1 is pre-cat and sensor 2 is post-cat.

Posted on Feb 03, 2010

wolfepac
  • 27 Answers

SOURCE: p0431 code on audi allroad 02

Typcally caused by one of the front oxygen sensors or a bad ground associated with these sensors.Replace both front sensors with direct fit type NOT universal, because there may be a cracked wire and the universal sensor does not contain the complete wire harness. Direct fits, are about $20 more than universal fit type.

The O2 sensors have integrated heating elements that bring them up to the proper operating temperature. Code P0431 indicates that the O2 sensor on your driver side catalytic converter is not reaching the proper operating range. The O2 sensors are usually in the $150 range online.

Posted on Jun 30, 2010

princeofscot
  • 288 Answers

SOURCE: I need to know where

This is what I found out for you on this web site at: http://www.obd-codes.com/trouble_codes/audi/

hope this helps

Posted on Jun 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Audi a4 1,8 s line


The computr needs a flash or reprograming w a factory scanner. It common not to recognize new motor. First make sure pins are clean on computr plug

Feb 06, 2016 | 2002 Audi A4

1 Answer

I have a 1999 Audi A6 quattro my right brake light went out I went to to switch the bulb and the bulb was OK but wont come on now I can't put my shift gear into gear without turning my lights on


There's should be a shift interlock that prevents it from being put into gear unless the brakes are on; check if the fuse it good for the brake lights; it seems to somehow be tied in with the parking lights, which may be feeding into the brake light circuit.

Sep 02, 2015 | Audi Cars & Trucks

3 Answers

I have a 2006 Ford E350 passenger van with 'Advance Trac'. The ABS light is on. I plugged in my Snap On scanner and it shows no codes. Took it to two other mechanics who scanned it, no codes on their...


it will not show a code ,whats wrong is either a wheel sensor or the toothed gear is loose on the drive shaft ,but newer fords do not use a toothed gear but a gray sort of paint on the bearing path which can get rubbed off with a piece of string getting wrapped around the drive shaft ,also i think you will find that they are now encrypting the software as well in line with the europeon market vehicles so as to make it a dealer only job .Try coming to europe for a holiday and bring your snap on scanner for a laugh and plug it into any europeon build for home market vehicle .If your lucky you may get the chassis number ,show it to any mecahnic in any garage in europe and they will tell you where the rubbish bin is to throw it in .

Dec 03, 2010 | 2006 Ford Econoline Cutaway

1 Answer

ABS warning light always on no effect on braking performance poss fix? Audi 100e 1992


Yes this can affect the brake performance, when the light is on a fault code is stored in the ABS control module, u will need to find out what that code is, a special scanner is needed to access this code, most brake shops and of course the dealer can do this test.

Jul 14, 2010 | 1992 Audi 100

2 Answers

Check engine light is on


Hi,


The check engine light in Audi comes on mostly when you have bad gas tank cup,or you dont tight enough the gasoline tank cup,you can see if the problem of the check engine light is from what i talking about,going to any autozone and request the obd scanner,at no charge just leave your driver license or credit card,connect the scanner follow the instructions.If the code in the scanner is p 1456,then the problem is that above,so dont panic car is almost normal,just give extra snap to the fuel tank cup and the check engine will come off in the next 3 to 5 days.


Thank you !

Jun 26, 2010 | 1991 Audi 80

1 Answer

Audi A6 RPM Signal from ECU


dont think you are reading the codes right because PO in front of the code is not a genuine Audi code ,well not according to my information ,try autozone who issue these codes or a snap on code reader booklet

Dec 26, 2009 | 2002 Audi A6

1 Answer

DDT auto transmission CODE stands for what?


evan an older car like this ,audi which is VW has computer for gearbox under passenger side floor .experiance i have had with one of these is that evan a snap on scanner cant read it .Once it goes wrong lose car and make an insurance claim.or fit a manual box..change the gear selector reader sensor on the box nearly 300€ ,overhaul gearbox 2000€ and still playing up ,computer got water into it ,didnt enquire the cost called a man ---- As for the so called expert with his snap-on scanner reading incorrect codes ,it was what i said all along ,when i found computer under floor after car had been driven through flood water ,then told iam an old dinasaur and this new man with his snap-on scanner said this was wrong and that and he knew all about autos,Yes he knew how to charge and make excuses for his incompetence

Dec 19, 2009 | 1997 Audi A4

2 Answers

Abs lights on plus brake warning light keeps flashing


It is very possible that the abs pump is faulty. As a mechanic myself, I recommend taking it to a dealer.

Sep 23, 2009 | 1998 Audi A6

1 Answer

1985 chevy s-10 rear blinkers dont work and no brake lights


First check all the fuses and make sure that they are good. The brake light wiring goes from the switch, through the turn signal switch, then to the brake lights. This is done so that when the turn signal is on and the brake light is on at the same time, the bulb will stay on steady on one side (away from the side you are signaling to) and the other side will flash.
If all the fuses are good, you have a bad turn signal switch. This requires a special tool (available at most parts stores or from the local Snap On man) to access the switch AFTER you remove the steering wheel.
Charlie

Jun 13, 2009 | 1983 Chevrolet S-10

1 Answer

Miss fire and lean codes


i have lost my mobile

Apr 17, 2009 | 2004 Audi A4

Not finding what you are looking for?
2001 Audi A6 Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...