Question about 1998 Ford Mustang

Open Question

How to change right front turn signal bulb on 1998 mustang gt

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1998 mustang gt coolant leak

I just had the same problem. Ford design the intake manifold with plastic water crossover which cracks. The coolant will leak onto the top of the block and and then down the back of the engine. This intake design is a known defect and was ocvered under by Ford for 7 years past the date of mfg. The crack either is in the crossover or the thermostat housing. I happed on this when I found the same leak and traced it back to the thermostat housing. I changed the thermostat, but it leaked worse. You can pickup a aftermarket for $200 and it's about 4-6 hr job to replace.

Posted on Oct 21, 2008

Ad
emissionwiz
  • 76164 Answers

SOURCE: Replacing rear turn signal bulb in 2003 Mustang

remove the trim panel at the very rear of trunk, remove it and place it out of the way, remove tail light Assembly retaining nuts top and bottom, I think there are 6 per side, pull the tail light assembly straight back to access the bulbs for replacement.

Posted on Dec 04, 2008

  • 1 Answer

SOURCE: Turn signal problem

broken ground wire

Posted on May 08, 2009

  • 1 Answer

SOURCE: Turn Signal Flasher location in 93 Mustang GT

The flasher is a small round plastic cylinder (unless replaced with a metal one) behind the left edge of the glove box that will look similar to the one in the fuse panel. The first step is to squeeze gently both sides of the open glove box and let it swing downward. It will be snapped into a metal horizontal brace just to the left of the glovebox opening by a small tab and have two wires attached. The number more than likely will be a #552 although I have seen a factory one with a Warner #224

Posted on May 13, 2009

  • 6 Answers

SOURCE: How do I change the turn signal bulb on 2000 Ford Mustang

Actually its easier that what the other guy said. lift your hood, look at the headlight there will be two rods that u can pull on the top of the light where it sits in the frame. pull those and u can then pull your headlight out, that will make it alot easier to get to.

Hope This Helps.

Posted on Sep 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 mustange gt brake light dont work check #9 fuses change all bulbs replaced switch on brake pedal hazards lights works ,parking or running lights works,turning signal lights works,what other places i...


I assume the fuse has power if the hazards work.
The third brake light skips the turn signal switch, the regular brake light circuit goes thru the turn signal switch.
Do you have power going into the turn signal switch on the red lite green wire from the brake switch ?

Feb 17, 2013 | 1995 Ford Mustang

3 Answers

I just noticed lately when I turn ON my turn signals, they start blinking twice normal then starts blinking really fast. And not all the rear light bulbs are ON. Could this be my turn signal...


If one of your rear bulbs is burnt out then the signals will react this way. 2007 is not very old of a car for a signal delay problem. It would be more likely a bulb.

Mar 01, 2011 | 2007 Ford Mustang GT California Special...

1 Answer

How do you change a 2002 mustang gt frunt turning signal bulb?


if it the bulb next to the headlight then you will have to loosen the hold screw on the top of the headlight assembly and remove the turn signal capsule forward to expose the bulb on the back of the assembly.

Jul 18, 2010 | Ford Mustang Cars & Trucks

1 Answer

Need to change the front right blinker signal bulb


look under the hood right behind the light bezel. you'll see where it plugs into the bezel. twist the light counter-clockwise.

Mar 29, 2010 | 1998 Honda Civic

1 Answer

Right side turn signals don't work.


if bulbs okay check fuse is good you got faulty turn switch or bad ground.

May 09, 2009 | 1998 Mercury Mountaineer

1 Answer

Turn signals on a 1998 ford mustang


when it acts up check and see if the bulbs are really flashing, could just be a bad socket for the bulb or a loose bulb, check them for that and also corrosion

Mar 27, 2009 | 1998 Ford Mustang

1 Answer

Replace front turn signal bulb on a 1998 Jeep Grand Cherokee


first remave the headlamp and then remove the marker lamp assy.

Oct 30, 2008 | 1998 Jeep Cherokee

Not finding what you are looking for?
1998 Ford Mustang Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...