Question about 2000 Chrysler Sebring

1 Answer

Ecm I have a 2000 chrysler sebring conv and I removed the ecm and had it tested because car would not accelerate over a certain speed and sometime would cut off and so I had the ecm checked and they said the processor was bad and had to replace with new one and now that I replaced new ecm the car will not start at all not sure what wrong

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 137 Answers

You need the new controller initialized from the dealer or a garage that has a DRB.

Posted on Jan 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Runs rough when it's warm. comes and goes. has a 2.7. and then a 99 dodge carvan with a 3.3 does the same thing.


Chrysler Sebring Questions - Car running very rough ...

www.cargurus.com > Questions > Chrysler > Sebring

CarGurusMar 27, 2011 - It seems after car gets to a certain temperature it runs very rough. ... 2011 at 12:16 PM about the 1998 Chrysler Sebring 2 Dr LXi Coupe ... it.one day it washot out and it was running sluggish with rough idle.and ... I changed the altnator and battery its runs like its brand-new.now ... 2002 Chrysler Sebring LXi.

Chrysler Sebring Questions - Engine Power Loss After Car ...

www.cargurus.com > Questions > Chrysler > Sebring

CarGurusNov 3, 2011 - Engine Power Loss After Car Is Warmed Up - Major loss of power after car has ... When vehicle is cold runs ok, sometimes a little rough but not bad. Full power. Allowed vehicle to run for over 45 minutes last night at idle, died on its own, car sat approximately 20-30 minutes. ... 2002 Chrysler Sebring LX.

* Chrysler Sebring/200 Convertible Club * • View topic - Rough ...

www.sebringclub.net/board/viewtopic.php?p=69097

Dec 29, 2006 - 5 posts - ‎3 authors
However, the vehicle still suffers from rough idle under certain conditions: ... been resolved (I don't think he noticed that it happened only when warm though). .... The test will tell you its general condition without having to dig it out of the fender, ..... Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group rough ...
15 posts
May 24, 2010
Low idle rpm
15 posts
Mar 8, 2007
More results from www.sebringclub.net

Jan 01, 2016 | 2002 Chrysler Sebring

1 Answer

2000 Chrysler Sebring Conv. Side mirrors and a/c not working. What would cause this


Side mirrors may be a wiring issue possibly near the driver door area where it would come from the door into the A pillar to under the dash,sometimes from age and door operation the wires break inside that harness.AC issue would need to be checked by a certified AC tech to check for leaks and operation,could also be a electrical issue or low on freon from a leak.

May 04, 2014 | 2000 Chrysler-03 Sebring 2 Door 00-01...

1 Answer

Where is the crankshaft position sensor located on a 2000 Sebring Conv.


removal steps (CPS) -remove air intake hose -Battery tray -Crankshaft position sensor

Apr 27, 2010 | 2000 Chrysler Sebring

1 Answer

I need to remove the fuel pump on my 00 sebring conv. do i have to remove the tank?


yes unfortunately you do . Because the fuel pump is located in the tank

Mar 26, 2010 | 2000 Chrysler Sebring

1 Answer

2000 sebring conv. I am trying to replace the input speed sensor and I cannot figure out how to get to it. I know where it is (I think) but its too hard to get to. Any advice?


If you are talking about the sensor for the speedometer, the only way I know to access it is from underneath the car. Be sure to disconnect the electrical connector first with a flat blade screw driver to lift the retaining tab. Then take your box end wrench, feel for the bolt head and remove it.

Nov 19, 2009 | 2000 Chrysler Sebring

1 Answer

Low speed ac blower motor does not work. Other


The heater blower motor has a blower resister. its in the heater box next to the blower motor, above the passengers feet. The bottom of the dash has a cover hold on with a few screws. the resister has a 4 or 5 wire plug and is heald in with 2 bolts, remove the connector then the bolts and it'll slide out. The new one may have to come from the dealer and have your VIN ready when you call. They'll have it or can get it in one regular day

Aug 29, 2009 | 2000 Chrysler Sebring

1 Answer

2000 chrysler sebring conv


this is the diagnostic procedure for your problem. (this is actually from a 3.0L engine but the procedure is exactly the same for the 2.5L)

click for full size
3f6ba68.jpg
2627050.jpg

5e54c06.jpg

Jan 20, 2009 | 2000 Chrysler Sebring

1 Answer

Throttle position sensor


its located on the opposite side of the throttle body as the throttle cable. remove the whole throttle body then remove the TPS from it.

Jan 15, 2009 | 2000 Chrysler Sebring

1 Answer

2000 sebring conv.


There are two little fasteners that need to be pryed/pulled off. They will pull off with a little force. I got one started with a screwdriver and the other with a pair of needle nose pliers. Once these two fasteners are off, the cover should come right out.

Jan 13, 2009 | 2000 Chrysler Sebring

Not finding what you are looking for?
2000 Chrysler Sebring Logo

Related Topics:

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...