Question about 2010 Toyota Fortuner 3.0D-4D

Open Question

Req. big end bearing torque for hilux 3.0 d4d

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 383 Answers

SOURCE: torque settings for big ends on a 97 toyota camry 220sei

On the V-6 it's 25 Nm (18 ft lbs) on the first pull and then you rotate the next pull 90 degrees using a torque angle wrench.

Checking the specifications for the four cylinder:
25 Nm (18 ft lbs) on first pull and 90 degrees
on the second pull using a torque angle wrench.

Posted on May 11, 2009

Ad
  • 158 Answers

SOURCE: fuel tank capacity ?

my research says 80

Posted on Aug 28, 2009

  • 277 Answers

SOURCE: Toyota diesel hilux D4D noisy engine.just

Take the Vehicle back to the Installer/Supplier, for a Free of Charge CHECK and ADVISE under New Engine Warranty. If the OIL PRESSURE is LOW, when starting up from COLD, there is a genuine fault, so do not drive any distance.
Regards,DT

Posted on Aug 28, 2009

  • 115 Answers

SOURCE: cylinder head torque settings for a toyota 1493cc

If you have a vehicle application for the motor you can get a Haynes or Chilton manual from your local auto parts store. They usual run around $30.

Posted on Sep 04, 2009

  • 4793 Answers

SOURCE: d4d smoking

try wynns/redexe to clean injectors/lines,they do seem to smoke a lot though....

Posted on May 02, 2010

Testimonial: "Thanks, yes, I thought common rail should be low emmisions, less particulate!?, but I'm not sure."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tilting backseat


glove box book

Hilux D4d Manual - lux-roc.com

www.lux-roc.com/hilux/hilux-d4d-manual.pdfToyota hilux tiger d4d sport cruiser manual pdf ' pdf owner ... Dec 05, 2014 Download Link: Pdf Download Toyota Hilux 2005-2011 Auto Repair Service Manual, ...

Oct 10, 2016 | Cars & Trucks

2 Answers

I need the big end torque on the Rocam engine please


A cheap shop manual will have this and much more. If you are in this deep you probably need one.

Sep 05, 2016 | 2000 Ford Ka

1 Answer

I own toyota hilux 2kd d4d that has a morning cold hard start, after first start all is ok


Excellent answer... short & spot on...
(except YOU didn't mention "OIL CONSUMPTION")

toyota hilux 2kd d4d... Not getting a lot of domestic... (USA)
DIESEL information... here (sorry).

From Bill Boyd here in 1994"

Toyota hilux pick up D4D has hard start in the morning but ok after the...

Jul 24, 2016 | Toyota Cars & Trucks

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

What is the torque setting for main bearing and big end bearing of a Toyota Yaris 1.0 1kr 3 cylinder?


Toyota Yaris Main and Big end Torques:
Tighten the main and big end bolts in sequential order and in steps two steps.
- Main bearings. Stage 1. 30 Nm.
Stage 2. 59 Nm.
- Big end bearings. Stage 1. 15 Nm.
Rotate further by 90 degrees.

Apr 09, 2015 | 2008 Toyota Yaris

1 Answer

How do I replace camshafts on Toyota Hilux 3.0 d4d?


The Toyota Hilux D4D 3.0 1KDFTV is an interference engine, so if the timing is wrong then the pistons will critically damage the valves. Removing the camshafts is easy, you just need to remove the set of bearing cap bolts that fasten them, in a predetermined order. When reinstalling the camshafts you just need to ensure the peripheral stamp marks on each of the camshaft sprockets align with each other. ie Align the indented dot with its adjacent indented dot or align the highlighted indented dot with its adjacent highlighted indented dot. The bearing cap bolts will need to be fastened with a torque wrench. Then connect the timing gear pulley onto the right camshaft using a key woodruff slotted into the right camshaft groove. Always double check the timing - that the peripheral stamp marks align. Don't under tension bolts, don't over tighten bolts either.

Sep 12, 2014 | Toyota Hilux Cars & Trucks

1 Answer

Torque specs bearing


Honestly you should search google. It is right there. the inner hub nut must be torqued to 59 Nm rotate the hub three times in each direction and then loosen the inner hub nut until it can be turned by hand, then again tighten the inner hub nut to 25 Nm. the lockwasher against the inner hub nut, it only goes in one way, it has a small inner tab that locates with the key way of the hub, this is between the threads. Once the lock washer is in the correct position, you can now install the outer hub nut, this outer nut must be torqued to 47 Nm, once you have tightened this outer nut, please once again check that the starting effort is correct.

Oct 18, 2013 | 2007 Toyota Hilux 2.5

1 Answer

HI HILUX SURF WITH 2LT DIESEL ENGINE CAN I GET CORRECT TORQE FOR. 1-TORQE FOR HEAD BOLT? 2-TORQE FOR CON ROD BEARING BOLT? 3-TORQE FOR MAIN BEARING BOLT?


Torque Settings Mains = 108NM
Big Ends = 54NM + 90° +90°
Flywheel = 122.5NM
Cylinder Head = 78 NM + 90° + 90°

Valve Settings
Exhaust = 0.40 mm - 0.50 mm
Intake = 0.20 - 0.3 0mm

Jun 30, 2011 | Toyota 4Runner Cars & Trucks

1 Answer

2002 audi tt 225 bhp cranksharft torque settings


Crankshaft torque settings for 2002 Audi TT 225 BHP:

1. Main bearings: Renew bolts = Yes
2. Main bearings: Stage 1 = 65 Nm
3. Main bearings: Stage 2 = 90 degrees
4. Big end bearings: Renew bolts / nuts = Yes
5. Big end bearings: Stage 1 = 30 Nm
6. Big end bearings: Stage 2 = 90 degrees
7. Flywheel / driveplate = 60 Nm + 90 degrees (use new bolts / nuts)
8. Crankshaft pulley / damper centre bolt = 90 Nm + 90 degrees (use new bolts)


Nov 25, 2010 | Audi TT Cars & Trucks

2 Answers

WOULD YOU KNOW THE TORQUE SETTINGS FOR MAIN BEARING AND BIG END BEARING CAPS FOR ISUZU 4JG2 ENGINE


Mains Stage 1 83nm
Mains Stage 2 167nm

Big ends Stage 1 29nm
Big ends Stage 2 45 - 60 degrees

Hope this helps

Jul 10, 2009 | 1994 Isuzu Trooper

Not finding what you are looking for?
2010 Toyota Fortuner 3.0D-4D Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...