Question about 2002 Jaguar X-Type

Open Question

I have codes P0102, P0112, P0118, P0335, P1229, P1646 AND 7, P1582, P1632, and P1236. Car is in limp mode, does not rev beyond 3000 and sometimes would not start, replaced a broken pipe from trapet

I travelled a long gravel road for two hundred kilometres before the fault appeared. Car moves very slowly if you press hard on the accelerator, it improves slightly with a light press of the pedal.

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 58 Answers

SOURCE: 1994 xj6 4.0 hard to start,runs rough and no power ,displays fuel

When this problem happens I would check the timing.  As your question was not fully reproduced, I would appreciate a more detailed description of your problem.  It could be the onboard computer has a fault and you are getting warning lights and the more obvious symptoms as a result.  Michael

Posted on Jan 15, 2009

  • 100 Answers

SOURCE: tick over problem

Sounds like it could be a bad EGR valve, the trans fault codes of p1775 is nothing really, it could even be the fact that you are putting the car in gear at 3,000 revs.
If this is an intermittant problem then it goes right back to the egr valve. They clog and stick and will cause bad/rough idle issues especially on start up and also will cause spiratic idle problems.

Posted on Feb 17, 2009

  • 3 Answers

SOURCE: Jaguar, S-Type, 2004 will not accelerate after dash sign came on

one of tha abs and traction sensors has blown

Posted on Feb 18, 2009

SOURCE: 99 jag xk8. I get stability control fault, car

Check your Throttle

Posted on Aug 13, 2009

  • 226 Answers

SOURCE: my jaguar goes into limp mode when i press the the

Check the TPS sensor. Sounds like it has a broken winding in it. (Can't see EGR being a problem on such a new vehicle.)

Posted on Aug 16, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Merc vito 2001 engine goes into limp mode but resets when turned off

The first thing that need to be done here is to have the fault code(s) read that are recorded in the computer's memory (PCM) when this happens. Do not keep driving the car or you will damage the engine and/or the transmission.

Jul 08, 2016 | 2006 Mercedes-Benz Vito 112

1 Answer

2002 jaguar xj8 when I drive it won't go over 3000rpm

Jaguar wont rev 3000 rpm Questions & Answers - Fixya > Forum > Tags > wont rev 3000 rpm
1998 Jaguar XJ8 won't rev over 3000 rpm ... Wont go beyong 3000 Revs s type 2001, wont go beyond 3000 Revs and it' in limp ... Question about 2002 X-Type ... My jaguar xjr8 year 2000 battery went dead started car went for short drive back ...

Jaguar engine cuts 3000 rpm Questions & Answers - Fixya > Forum > Tags > engine cuts 3000 rpm
1998 Jaguar XJ8 won't rev over 3000 rpm ... engine cuts out and shudders at 3000 rpm won't accelerateobd code p0332 2002 jaguar x type 3.0 l P0332 - Knock ... Car is boging out in park and will not go over ... driving, don't worry about it.

Rev Won't go up

Dec 15, 2015 | Jaguar Cars & Trucks

1 Answer

Limp ModeEngine starts, idles fine but will; not rev over 3000 rpm and does the on/off hunting thing at 3000

Year make and model? Any codes? Engine and transmission codes will cause a limp mode.

Dec 15, 2015 | Cars & Trucks

1 Answer

P1582 jaguar s type

the 1582 code is a flight recorder code meaning that at some point one of the following has happened: the inertia switch has been triggered,throttle body signal has triggered the limp mode,the engine starts but stumble and then shuts off,or engine fail to start,or a engine stall has occured.This is what causes this code.If the issue was resolved,clear the code becuae it can become permanent and although the car will run fine the code will be there without a mil showing.

Mar 21, 2014 | 2003 Jaguar S-Type

1 Answer

Navara d40 has no power wont rev more than 3000 rev thanks

Sounds like your vehicle is in limp mode. Check for faults with a fault code scanner at a local auto parts store. Resetting the fault will fix the limp mode, but not whatever caused your vehicle to initiate limp mode.

Sep 12, 2013 | Cars & Trucks

1 Answer

S TYPE 2001 Wont go beyong 3000 Revs

No, You have a high pressure fuel system. Things are not that simple anymore.
You need to get it checked properly as the fault is in the engine managment system.
The limp mode is the car protecting itself from you and allowing you to get home. Thats it.
Get to know a good mechanic

Oct 06, 2009 | 2001 Jaguar S-Type

Not finding what you are looking for?
2002 Jaguar X-Type Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

80608 Answers


Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides