Question about Cars & Trucks

Open Question

BLEEDING CLUTCH ON IVECO CARGO LORRY

HOW TO BLEED THE CLUTCH

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 16 Answers

SOURCE: location of brake/clutch bleed valve nipple

AHH look for it by the slave cylinder it might have a black rubber cap on it to keep dust out it will look simliar to the bleeder valve on the brake system

Posted on May 09, 2009

fastboyz
  • 674 Answers

SOURCE: bleeding hydraulic clutch

well you will need some help
make sure the resivor is full and have someone hold the clutch pedal to the floor and crack the bleeder on the slave cyl. and close after the spert of fluid comes out. when the screw is closed have the person in the drivers seat slowly let up and push down 3 times and hold down and bleed one more time. refill your resivor and repete if you dont think the peddal is quite right. just dont run it out of fluid
good luck it realy isnt that hard.
later paul

Posted on Sep 16, 2008

  • 275 Answers

SOURCE: Bleeding clutch slave cylinder

if you loosten the slave bleeder screw and push in the clutch pedal fluid should come out if not make sure someone holds down the pedal and tighten the screw then pump the clutch a few times and hold the pedal and open the screw if no fluid repeat a couple of times if still no fluid you need either a new master cylinder or just rebuild it( normally cheaper) and if you rebuild it make sure you flush all the lines of debris

Posted on Nov 12, 2008

rockitman187
  • 2559 Answers

SOURCE: clutch goes to floor will not engage

Bleeding won't fix it,If it can be put in gear and car doesn't move your clutch is no good.

Posted on May 28, 2009

  • 2187 Answers

SOURCE: Bleeding Clutch Cylinder with no bleeder screw

I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Posted on Jun 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed clutch cylinder for Nissan Sandra 2010


bleed clutch cylinder Robinny, Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Bleeding clutch
Clutch bleed how to
Nissan Altima 2007 2012 Service Manual Clutch fluid On vehicle maintenance...
Help clutch bleeding Fail

Jul 19, 2016 | Nissan Cars & Trucks

1 Answer

Need help bleeding clutch


Clutch bleeding can be problematic and I have had to resort to removing the slave cylinder but leaving the hydraulic line connected and raising it as far as the flexible pipe will allow. above the master cylinder and bleeding it in mid-air.

Reverse bleeding can be very effective and with a long-travel large capacity cylinder the piston can be pumped out to the limit of its travel and then forced very quickly back in as far as it will go.

Anotther type of reverse bleeding I have been forced to employ a few times is connecting the clutch bleed screw to a nearby brake bleed screw with some very good fitting hose. Both bleeders are opened and the clutch is bled by pumping the brake pedal. An assistant adds fluid to the brake reservoir and removes it from the clutch reservoir.
Four or five vigorous pumps usually does the trick.

Good luck!

Feb 12, 2015 | 1996 Ford Explorer

2 Answers

How do you bleed a hydraulic clutch on a 1977 corvette


you bleed like you would the brake system. there is a bleeder screw on the slave cylinder that you bleed the system.

Oct 11, 2014 | 1977 Chevrolet Corvette

1 Answer

I want replaced diesel filter from dyna lorry


there are 2 types, one is just a cartridge just like a small oil filter, this one just unscrews like an oil filter, when you replace it there is a round knob that unscrews and becomes a pump, just pump it until it becomes firm then try starting it with your foot on accelerator until engine starts. The other has a filter with a bowl under it, they have a small bolt in the center top of the housing, undo the bolt and the filter will drop free of the housing. these have O rings top and bottom and a bleed nipple off center, loosen the bleed screw pump the pump until air stops coming out the bleed, close bleed nipple then follow the same start procedure. any fuel leaks will stop your engine from starting but do not over tighten either filter because they can be damaged

Nov 26, 2013 | Cars & Trucks

1 Answer

How do i bleed clutch on fiat dublo


Clutch systems bleed just like brakes, if you have an external leak at the clutch master cylinder, then bleeding will be difficult, it should be replaced. I use a two person bleeding system, I fill the master, crack the bleeder screw open and have my 2nd push the clutch down and hold it, then I close the bleeder and tell my 2nd to release the pedal, repeat until no air is present.

Sep 11, 2012 | Fiat Doblo Cars & Trucks

3 Answers

How do you bleed the clutch hydraulic system on a 2008 Mustang?


you bleed a hydraulic clutch the same way you bleed a brake system and it uses brake fluid as well.you keep bleeding until there is no more air in the clutch system.there should be a bleeder screw on the clutch slave cylinder that is were you bleed the clutch from.

Mar 18, 2011 | 2008 Ford Mustang

1 Answer

1987 Maxima-5 speed is difficult to grt in to gear--How to adjust clutch and check clutch hydraulic fluid?


TO ADJUST PEDAL HEIGHT ADJUST WITH A STOPPER LIMITING THE UPWARD TRAVEL OF THE PEDAL.PEDAL FREE PLAY IS ADJUSTED AT THE MASTERCYLINDER PUSH ROD.IF PUSH ROD IS NON ADJUSTABLE FREE PLAY IS ADJUSTED BY PLACING SHIMS BETWEEN THE MASTERCYLINDER AND THE FIREWALL.ON A FEW MODELS PEDAL FREE PLAY CAN ALSO BE ADJUSTED AT THE OPERATING SLAVE CYLINDER PUSHROD.PUSHRODS ARE AVAILABLE IN THREE LENGTHS FOR THE 310.PEDAL HEIGHT ABOVE FLOOR IS 6.73 - 7.13 INCH PEDAL FREE PLAY IS 0.04 - 0.12 INCH.YOU HAVE CLUTCH FLUID LONG AS YOU SEE BRAKE FLUID IN MASTERCYLINDER.IF MASTERCYLINDER LOW YOU HAVE TO BLEED THE THE CLUTCH MASTERCYLINDER BY LOCATING BLEED SCREW ON SLAVE CYLINDER. REMOVE THE BLEED SCREW DUST CAP.ATTACH A CLEAR TUBE TO THE BLEED SCREW.PUT OTHER END OF CLEAR TUBE IN A CLEAN CONTAINER OF BRAKE FLUID.FILL THE MASTERCYLINDER WITH BRAKE FLUID.OPEN BLEED SCREW 3/4 A TURN.DEPRESS CLUTCH PEDAL QUICKLY.HOLD IT DOWN.HAVE A HELPER TIGHTEN THE BLEED SCREW.ALLOW PEDAL TO RETURN SLOWLY.BLEEDER SCREW TORQUE IS 5 - 6 FT LBS.IF YOU SEE AIR BUBBLES CLEAR BLEED TUBE.REPEAT THE BLEED PROCESS UNTIL YOU SEE NO AIR BUBBLES.DONT LET CLUTCH MASTERCYLINDER GO DRY WHILE BLEEDING.IF SO YOU GOT START BLEEDING PROCESS ALL OVER.HOPE THIS HELP.

Aug 05, 2010 | 1987 Nissan Maxima

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...