Question about 2006 Hummer H3

Open Question

P2101 trouble code on 2006 Hummer H3

Traction failed, reduced power, service STAB SYS all being displayed as issues. Trouble code P2101

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 78 Answers

SOURCE: BRAKE SYSTEM FAILURE

well what could of happend they probably put the battery on backwards and blew out a fusible link.The links run thru the wires by the battery and behind the alternator check it out Good Luck keep me posted

Posted on May 27, 2009

Ad
carputers
  • 255 Answers

SOURCE: 2008 Hummer H3 The trackion failed light on

clean abs sensors at each wheel.

Posted on Sep 08, 2009

swampthang90
  • 18 Answers

SOURCE: 2006 Hummer H3 a/c & heater fan/blower failed

Probably too late now, I am sure you have already fixed it, but mine did this and it was an electrical part that is mounted right beside the blower fan. The part was OK, but the plug into the part was arcing and burned out the connection. A Chevy mechanic told me this has been happening to MANY Chevy products. I had to buy a new part and plug assembly with new wires, about 100 dollars, and I spliced them together. It was an Easy fix, but I shouldn't have had to do it :(

Posted on Mar 07, 2010

  • 1 Answer

SOURCE: 2006 H3 Hummer fan problem

Hi if your internal fan not work in any position well i fixed up myself easy and save your money.
locate the fan motor air just outside right courtesy drawn document in front of passenger. go from down and look up you will see a motor with a big connector white with 2 screw secure inside the motor block. loose the two screws and pull out gently the connector from motor fan block. you will see a green multiresistor connected with this big connector. Usually the first + voltage connector is burnet out. disconnect the connector pull from resistor and check for any burn. in my case the first pin was burned out completely
you can buy another connector or you can clean the burned connector take out form connector weld a small copper cable of 5 mm dia from resistor to the burn cable and reconnect the connector without buy a new one. after replace again the resistor in the hole of motor blow with the 2 screw.
Done all work again without buy another new connector.
Gabriel from Italy Turin
H3 hummer 2007
loveling one and Humvee owner

Posted on Jun 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HI,can a car who has fault service stab sys traction failed abs shown on their vehicle continue to drive it or does it need to be fixed as soon as possible. thank you for your reply


You can still drive it but the ride and safety will be affected. I recommend you get vehicle fixed at earliest as can. The vehicle will skid if hit brakes hard. Stability will also be affected

Jul 16, 2016 | 2007 Hummer H3X

1 Answer

Fault service stab sys traction failed abs is what my h3 has been showing. can you help me figure whats wrong and how much it would cost to fix. thank you


It has to be on a scanner to see what is wrong. Could be a bad wheel sensor. Could be a broken wire at a wheel sensor. Could be the ABS module died. Garage costs. Broken wire (2hour minimum) $200, sensor up to $400+, module$1000+

Jul 14, 2016 | 2007 Hummer H3X

1 Answer

My 2006 hummer h3 keeps shutting off and saying no traction reduced power


The anti lock and slip sensors may be dirty or damaged causing misinformation to the vehicle computer.

Jun 16, 2014 | 2006 Hummer H3

2 Answers

My hummer 07 h3 starts for a second then dies. My security light is on. What can I do to fix it?


This is a failed antitheft system. Go to this link for info and ways to fix it yourself

http://vatspasslockpasskeysecurityhelp.yolasite.com/

May 13, 2012 | 2007 Hummer H3X

1 Answer

BRAKE SYSTEM FAILURE


well what could of happend they probably put the battery on backwards and blew out a fusible link.The links run thru the wires by the battery and behind the alternator check it out Good Luck keep me posted

May 27, 2009 | 2006 Hummer H3

Not finding what you are looking for?
2006 Hummer H3 Logo

Related Topics:

252 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...