Question about Cars & Trucks

1 Answer

If my oil sending unit is out will my truck break down

Oil pressure gauge reads 80 psi. drops to 0 psi computer tells me low oil pressure does the oil sending unit only give oil pressure gauge readings

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 57 Answers

Yes,it reads oil pressure only,if its out as long as it was working fine before it went bye bye your fine,you won't blow up engine or break down.

Posted on Nov 29, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 147 Answers

SOURCE: wireing diagram for 1980 K2500. Electronic oil

try this linkhttp://www.automotix.net/autorepair/diy/1996-gmc-k2500_pickup-repair.html

Posted on May 08, 2011

  • 75 Answers

SOURCE: oil pressure gauge goes to 80 psi when the truck key is turned on

chances are your sending unit is not bad. These dashes have had alot of problems with stepper motors failing in the instrument cluster. does it go to zero when key is off? is it erratic? changes where it sits when running and when off? These are all problems within the cluster itself. It is not cheap to take this to the dealer. THey will want to replace the cluster. these clusters can be repaired for half the cost if you know where to go. Not sure yet what the rules are on here but i can repair these for about 325 verses over 600 from dealer and then reproggramming costs! One other note. Chevy has a recall on these! call you local dealer and ask what the criteria is for the recall. You may be able to get it repaired for free if you meet the time frame and mileage requirements.

Posted on Feb 01, 2010

emissionwiz
  • 76164 Answers

SOURCE: oil psi gauge reads well over 80 when engine is

no this sounds like a defective gauge, a sending unit cause this symptom

Posted on Oct 20, 2009

  • 1608 Answers

SOURCE: oil pressure gauge is reading 80 psi. I had the

The oil sending unit is located on the engine block behind the drivers cylinder head area.You have to climb up on the motor to see it cause it is hard to see behind the wiring harness.You may also want to purchase a new sending unit because it is very long and you might need to buy the sending unit socket to replace it.Hope this helps.Good luck.

Posted on Jul 20, 2010

  • 67 Answers

SOURCE: oil pressure gauge reads 80 psi but computer reads

to be accurate on the reading i would use a oil psi guage and see the reading, and see what it says so you can compare the results.

Posted on Feb 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know where the fuse is for oil sending unit on a 1998 Buick Park Avenue with a 3800 v6


There is no fuse for the oil sending unit ! Oil lite on , gauge not working ? Do you know what PCM five volt reference voltage is ? The PCM - engine computer supply's a stable 5 volt voltage to engine sensors . The oil pressure sensor is one of these sensors .
Engine Oil Pressure Sensor
The engine oil pressure sensor is a solid state transducer. The engine oil pressure sensor sends oil pressure information to the PCM. The PCM then transmits the oil pressure information to the IPC via serial data.
Engine oil pressure is displayed on the scan tool in volts. A low voltage reading indicates low oil pressure. As the oil pressure increases, the voltage level also increases. The normal range of the engine oil level sensor signal voltage is 0.5 volts at 0 kPa (0 psi) to 4.5 volts at 883 kPa (128 psi).

Jul 02, 2017 | Buick Cars & Trucks

1 Answer

96 Chevy blazer how do I get out of safe mode ran low on oil now runs an drives but won't let car go fast past 2000rpms


The computing system on your vehicle has no safe mode for running low on oil . The only thing that will happen is the check gauges light will come on.
The oil pressure gauge is an analog device that is located in the IPC. The oil pressure gauge is operated directly by the oil pressure sensor circuit. As the engine oil pressure changes, the resistance of the sensor and the current flow in the oil pressure gauge changes. The current flow in the oil pressure gauge causes the needle to move in order to appropriately display the engine oil pressure. A sensor resistance of 1ohms will display as 0 kPa (0 PSI) and a resistance of 88 ohms will display as 80 kPa (80 PSI ). The IPC also monitors the oil pressure sensor circuit and interprets the current flow in this circuit in order to determine when the engine oil pressure is too low. If the oil pressure is too low, the check gauges tell tale will turn on. The oil pressure sender is located on the left side of the 2.2L. The 4.3L engine, oil pressure sender is located at the top left side, near the distributor/high voltage switch.
Try disconnecting the battery cables an hold them together for ten minutes , reset ECM !

Nov 08, 2015 | Cars & Trucks

1 Answer

How do i tell if i have a bad oil pump or a bad oil sensor


If oil level in engine is at proper level, I wouild suspect oil pressure sending unit, does vehicle have an oil psi gauge on dash,,,if so what does it read. if oil psi reads well then it may be an oil level sensor. if you have access to a manual oil pressure gauge, you can remove the oil psi sensor and install manual gauge to get a true reading of what oil pressure is while running. if manual gauges shows low psi, then you may be looking at an oil pump.

DW Mylin

Nov 27, 2012 | 2006 GMC Envoy

2 Answers

How can i fix the oil pump


see this tips and fix it. God bless you
The oil pump supplies oil to lubricate your engine. If the oil pump is worn or is not turning, the engine will suffer a loss of oil pressure, which may result in engine damage or engine failure.
The first sign of trouble may be a low oil pressure warning light, a drop in the normal reading on you oil pressure gauge (if your car has one), or the appearance of ticking or clattering sounds from your engine.
As a rule, most engines only need about 10 PSI of oil pressure for every 1,000 RPM of engine speed. Oil pressure will read higher than normal when a cold engine is first started because the oil is thick. Oil pressure will gradually drop as the engine warms up and the oil thins out. So normal oil pressure on a warm engine cruising down the highway is typically 30 PSI up to 45 PSI.
SYMPTOMS OF OIL PUMP TROUBLE
The first thing you should do if any of these symptoms occur is to stop your car, turn off the engine, let it sit for a few minutes, then check the oil level on the dipstick. If the oil level is at or below the ADD line, add a quart of oil to bring the level back up to the full mark. Add as much oil as is needed to raise the level to the full mark. Then restart the engine. If the warning light remains on, or the oil pressure reading does not climb back up to its normal range, or the engine noise does not go away, you may have a bad oil pump.
The other possibilities include a bad oil pressure sending unit, or a problem with the oil pressure warning light circuit or oil pressure gauge.
OIL PRESSURE SENDING UNIT
If the engine is NOT making any unusual noises and seems to be running normally, and the oil level on the dipstick is FULL, but you are still getting a low oil pressure warning light or low gauge reading, the fault could be a bad oil pressure sending unit.
The oil pressure sending unit is mounted on the engine block. On some applications, there is a spring-loaded pressure-sensitive diaphragm with a switch inside the sending unit. This switch completes the circuit to the low oil pressure warning light if oil pressure drops below a certain threshold. The unit may stop working if the diaphragm inside fails, if the switch is stuck, if the small hole that allows oil to enter the sending unit becomes plugged, if there is a loose, corroded or broken wiring connector at the sending unit, or there is a fault in the wiring circuit between the sending unit and warming light.
On vehicles that have an oil pressure gauge (electronic, not mechanical), the oil pressure sending unit has a small rheostat inside that sends a variable voltage signal to the oil pressure gauge when the diaphragm moves. A worn spot on the rheostat or any of the other problems just described for the simple pressure-type oil pressure switches can cause a problem.
FORD'S FAKE OIL PRESSURE GAUGE
On many Ford vehicles that were built from 1980 through the 1990s, the oil pressure sending unit has two switches, a low pressure and a high pressure. These vehicles also have an oil pressure gauge, but the reading on the gauge is not a true indication of real oil pressure. As long as the pressure to the sending unit is between high and low, the gauge will read normal. If oil pressure drops and trips the low pressure switch, the dash gauge will now read low. Or, if oil pressure goes up and trips the high switch inside the sending unit, the dash gauge will read high. Consequently, don't rely on the oil pressure gauge for an accurate reading in these vehicles. It is only a gross indication if the oil pressure is low, normal or high.
OIL GAUGE PROBLEMS
If the engine is NOT making any unusual noises and seems to be running normally, the oil level on the dipstick is FULL, and you have replaced the oil pressure sending unit but are still getting a low oil pressure reading on the dash gauge, the fault could be in the wiring circuit between the sending unit and gauge, or the gauge itself might be bad.
Check the wiring connections on both ends as well as wiring continuity between the sending unit and gauge. If no wiring faults are found, hook up a pressure gauge directly to the oil pressure port on the engine and check oil pressure with the engine running. If the engine-mounted gauge shows normal oil pressure but the dash gauge is reading low, the problem is a bad dash gauge.
On the other hand, if the engine-mounted pressure gauge reads low and you have done all of the above, chances are the oil pump is worn, or it is not picking up enough oil because of a restriction or blockage in the pickup screen in the bottom of the crankcase.
OIL PUMP PICKUP PROBLEMS
The pickup tube has a screen on the end to prevent large chunks of anything bad that ends up in the crankcase from being sucked into the pump. But we are talking BIG chunks of debris, not normal wear particles or carbon or dust or other microscopic-sized abrasive particles that can cause pump wear over time.

Sep 28, 2012 | 1996 Toyota Tercel

1 Answer

NO OIL PRESSURE READING ON DASH


remove sending unit and install mechanical gauge to see oil pressure psi if psi reads ok- change sending unit again if psi to low less then 6 replace oil pump och.

Sep 18, 2012 | 1990 Toyota 4Runner

1 Answer

Oil pressure gauge going up and down


Engine 'knocking'? If not, replace oul pressure sending unit.

Sep 18, 2017 | 2006 Chevrolet Silverado 1500 2WD

2 Answers

Oil pressure gauge is reading 80 ..could a wire had come loose? If so , where could I find the wire??


Unplug the oil sending unit. If you had posted a year make model and engine size I could have told you where to look Generally they are near the oil filter unless it is a truck.

If the gauge reads zero with it unplugged replace the sending unit. If the gauge still reads 80 psi you will need to read data with a scan tool. If data says 80psi you have a wiring issue. If data says 0 than you have a bad gauge.

More often than not it is the sending unit.

Jan 23, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Oil pressure gauge is reading 80 psi. I had the


The oil sending unit is located on the engine block behind the drivers cylinder head area.You have to climb up on the motor to see it cause it is hard to see behind the wiring harness.You may also want to purchase a new sending unit because it is very long and you might need to buy the sending unit socket to replace it.Hope this helps.Good luck.

Jul 20, 2010 | 2003 Chevrolet Silverado 1500

4 Answers

Oil pressure reading in 2003 gmc envoy


No problem with the oil pressure, the norm is between 40 to 60. Anything lower then 40 you have low oil pressure and anything above 60 then you have high oil pressure which is caused by a blockage in the system.
What is common is the oil pressure gage fluctuating for the first 200 miles if the oil pressure sending unit is getting worn. Good maintenance will keep the engine clean and running good but the oil pressure sending unit is inexpensive and easy to replace. Next time you do an oil change you can have them change the sending unit.
Good luck and hope this helps. You can pick up the sending unit at Auto Zone and most auto parts store and will have the step by step to replacing it. If you do attempt to replace it. make sure you DO NOT USE any Teflon tape or silicon on the threads, they are tapered and need a good ground to the engine for proper readings.

May 28, 2009 | 2004 GMC Envoy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...