Question about 2002 Mitsubishi Lancer
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Here is a link that should help you get the wiring colors you asked for. Good luck and hope this helps. http://www.installdr.com/Harnesses/Mitsubishi-Wiring.pdf
Posted on Oct 28, 2009
i dont have a pic but it goes like this..
(color1/color2 usually means the wire has a stripe or dots on it)
Car Radio Battery Constant 12v+ Wire: Red/Black
Car Radio Accessory Switched 12v+ Wire: Blue
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Green/White
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger: Yellow
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): White/Blue
Left Front Speaker Negative Wire (-): Black/Blue
Right Front Speaker Positive Wire (+): White/Red
Right Front Speaker Negative Wire (-): Black/Red
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Yellow/Blue
Left Rear Speaker Negative Wire (-): Gray/Blue
Right Rear Speaker Positive Wire (+): Yellow/Red
Right Rear Speaker Negative Wire (-): Gray/Red
Posted on Oct 28, 2009
YOUR CAR ONLY HAS COIL PACKS. CHECK VOLTAGE AT HARNNESS, IF OK REMOVE COIL PACK FROM SPARK PLUG REMOVE BOOT CHECK FOR VOLTAGE THERE, IF NONE POSS. COIL PACK.
Posted on Nov 05, 2009
SOURCE: 2002 mitsubishi lancer es manual
eBay has these manuals available. Item # 270544305731
Sells for 6.99 to 7.99 + .99 for shipping.
This is the repair manual and is a CD for use with a PC.
They have owners manuals for some models too.
Posted on Mar 10, 2010
SOURCE: Where is the starter located
I replaced the starter on my daughters 2002 lancer and did it the hard way by crawling under the car to figure out where it was first, and then working underneath to get it out. After performing the procedure I realized there is a much easier way to do it.
- The starter is located on the back side of the engine under the intake manifold towards the drivers side of center. It is very difficult to see from the top with everything still assembled.
Replacing the easy way:
1. Disconnect negative battery cable.
2. Remove the plastic air filter box first. After it is off you can easily see the starter down by the shifter linkage bracket.
3. Remove two bolds holding the shifter linkage bracket so it can be moved out of the way.
4. Remove wiring connectors from back of starter solenoid. One connector is just a slide on, the other main wire is held on by a metric nut. That one may look impossible to get at, but if you configure a 1/4 drive ratchet with the right sized deep well socket you have room to work it through a cut out in large mounting bracket that you will see below. I'm thinking the Japanese engineers put the cut out there for this purpose.
5. Remove two starter mounting bolts and allow the starter to slide down and back so as to rest on the bracket below.
6. Walk around to the passenger side of engine and reach down under intake manifold to pull starter up and out.
7. Reverse procedure to reassemble.
8. Done without ever crawling under the car!
Posted on Feb 11, 2011
Tips for a great answer:
Sep 29, 2015 | Mitsubishi Cars & Trucks
Jan 20, 2014 | 2002 Mitsubishi Lancer
Feb 11, 2011 | 2002 Mitsubishi Lancer
Jul 26, 2010 | 2002 Mitsubishi Lancer
Mar 30, 2010 | 2002 Mitsubishi Lancer
Nov 04, 2009 | 2002 Mitsubishi Lancer
Oct 28, 2009 | 2002 Mitsubishi Lancer
Aug 18, 2009 | 2002 Mitsubishi Lancer
Mar 18, 2009 | 2003 Mitsubishi Lancer
Jun 30, 2008 | 2002 Mitsubishi Lancer
37 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: