Question about Cars & Trucks

Open Question

Reprogreamming A Ford Ka remote ignition key

Lost remote fob now found by police will no longer work as the car has been reprogrammed by Ford garage. Can I reprogramme the old remote key

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 13 Answers

SOURCE: focus remote key fob not working

this info would cost you £30.+ at ford Radio Frequency Programming Instructions:

  • Insert the ignition key and turn from position II (Ignition) to position 0 (All off) and back four times within three seconds.
  • Remove the ignition key. The locking control system is now in "learn mode" for the next 20 seconds and the red warning system LED (By the clock) stays on continuously to indicate this.
  • During the 20 seconds press one of the transmitter buttons. The remotes signal and code number is learned by the locking module and is indicated by flashing the warning system LED.
  • Wait until learn mode times out (20 seconds) or switch the ignition back to ON.nfrared Programming Instructions:
  • Put your key into the ignition and turn to position 1 (Radio). After approximately 10 seconds the red alarm control LED (next to the clock) should illuminate. As soon as it comes on remove the key from the ignition - the LED should remain lit.
  • Point the remote's "eye" at one of the front door sensors and press the rear button until the light on the transmitter illuminates (Keep the button pressed)
  • With the rear button held in press the front button 4 times then release both at the same time. The control lights in both clock and fob will flash 4 times to indicate programming complete.
  • Turn the ignition back on to exit programming mode

Posted on Dec 01, 2008

blueextc3221
  • 15935 Answers

SOURCE: remote key fob will not work-battery replaced

VW/AUDI/SEAT/SKODA



Remote Control Programming (1997 ON)

Procedure
1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second
key.

3. Using the remote control press the Unlock button once, and the horn
will sound once.

4. Wait 6 seconds and press the unlock button once to activate the coding
procedure. The remote control will now be programmed.

NOTE : When performing programming on additional remotes the procedure
is the same, except you press the unlock button 2, 3 or 4 times for the
different remote.

For example : If programming 2 remotes press the unlock button twice with
a 1 second interval between each press, repeat for 3 and 4 remotes.

5. Switch Ignition OFF.

6. Remove key from ignition and check for operation.

7. The coding procedure can be repeated up to 4 times for additional remotes.

8. The ignition must be switched OFF between programming each remote
control.

Remote Control Erasing (1997 ON)

Procedure
1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second
key.

3. Press the remote control unlock button 5 times in 1 second intervals.
A short horn will sound.

4. Wait 6 seconds and press the unlock button once to activate memory
erase.

5. Switch ignition OFF, all remotes are now erased.

Posted on Dec 24, 2008

  • 1 Answer

SOURCE: reprogramming blank key iveco daily

Unfortunately there is no solution to this except to take it back to Iveco for reprogramming.

I am led to believe from my locksmith that there are two types of transponders generally put into cars and vans.

The first is a simple chip wtih a code which matches a code in the car / Van

The second is a chip which has a set of codes. They are read in order and the car / van remembers which one was used last. If you use the wrong code in the sequence then the car / van will ignore it and not let you start the engine.

The Iveco is unfortunately in the second group. If, like me, you snap your key, you can superglue a new key to the old and it works fine. The chip doesn't need to be "too" close to the barrel. Yes, it looks ugly, but it's much cheaper!

Posted on Apr 19, 2009

  • 1986 Answers

SOURCE: remote key fob won'tprogram

1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works

Posted on Aug 13, 2009

  • 2 Answers

SOURCE: my renault laguna 1999 rt remote key fob wont work?

IF YOU TYPE 1999 RENAULT LAGUNA REPROGRAMME KEY INTO A GOOGLE SEARCH, YOU WILL BE ABLE TO PRINTOFF INSTRUCTIONS TO REPROGRAMME THE KEY TO THE KEY READER.THE IGNITION NEEDS TO BE OFF TO DO THIS

Posted on Dec 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Saab experts


May be keyfob needs reprogramming.

Keyfob remote reprogramming is not very difficult but on some cases it can be done by dealer service tools.

If the remote s faulty then key fob will not get programmed.

Insert the key in ignition. Turn the key to on position, and cycle the key three times off-on-off-on-off-on. Then with the key fob remote select your remote and then try to operate the vehicle with remote.

These are just the basic procedure, but sometimes it will not help.

On that case dealer is the only option.


---------

There are few much related troubleshooting links mentioned below for remote key fob reprogramming. I suggest you to go through the list and click the link below to go through its details and procedure: -------




Theft indicator not letting car to start?

http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html

-------------



2009 Toyota Highlander: Smart Key Not getting Detected?

http://whatisbyme.blogspot.in/2012/05/2009-toyota-highlander-smart-key-not.html


----------

2007 Toyota Prius: Reprogram Remote Keyfob?

http://whatisbyme.blogspot.in/2012/05/2007-toyota-prius-reprogram-remote.html

-----------

Pin that holds the flick key part to the key fob?

http://whoisbyme.blogspot.in/2012/07/pin-that-holds-flick-key-part-to-key-fob.html

-------------


2006 Toyota Hilux: Programming New Key?

http://technoanswers.blogspot.in/2012/04/2006-toyota-hilux-programming-new-key.html

----------

Where is Key chip memory located on 2004 ford Freestar?

http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html

----------

Ford Keyless Remote Fob Reprogramming?


http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html

----------

After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?

http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html

-----------

Audi A8 Key Fob Programming?


http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html

----------------

Oldsmobile Aurora Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html

-------------

Buick Lesabre Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html

---------------

Keyfob remote not working on 2003 Ford E350 Econoline?

http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html

-----------

KeyFob will open the doors but not start on BMW?

http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html

------------

Mitsubishi Car Key Not getting detected after replacing ECM

http://repairhelpcenter.blogspot.com/2012/11/mitsubishi-car-key-not-getting-detected.html

-----------

Key Fob will not lock and unlock doors?

http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html

-------------

2000 Jeep Cherokee Limited: KeyFob Remote Not Working?

http://schematicsdiagram.blogspot.in/2012/06/2000-jeep-cherokee-limited-keyfob.html

-----------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

-----------

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html

--------------


These details will help.

Thanks.

Dec 04, 2012 | Cars & Trucks

1 Answer

Peugeot 206 key fob


Try with brand new key fob battery and see.If that helps.
Otherwise May be keyfob needs to be reprogrammed.

KEYFOB PROGRAMMING


Keyfob remote reprogramming is not very difficult but on some cases it can be done by dealer service tools.

If the remote s faulty then key fob will not get programmed.

Insert the key in ignition. Turn the key to on position, and cycle the key three times off-on-off-on-off-on. Then with the key fob remote select your remote and then try to operate the vehicle with remote.

These are just the basic procedure, but sometimes it will not help.

On that case dealer is the only option.


---------

There are few much related troubleshooting links mentioned below for remote key fob reprogramming. I suggest you to go through the list and click the link below to go through its details and procedure: -------

2009 Toyota Highlander: Smart Key Not getting Detected?

http://whatisbyme.blogspot.in/2012/05/2009-toyota-highlander-smart-key-not.html


----------

2007 Toyota Prius: Reprogram Remote Keyfob?

http://whatisbyme.blogspot.in/2012/05/2007-toyota-prius-reprogram-remote.html

-----------

Pin that holds the flick key part to the key fob?

http://whoisbyme.blogspot.in/2012/07/pin-that-holds-flick-key-part-to-key-fob.html

-------------


2006 Toyota Hilux: Programming New Key?

http://technoanswers.blogspot.in/2012/04/2006-toyota-hilux-programming-new-key.html

----------

Where is Key chip memory located on 2004 ford Freestar?

http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html

----------

Ford Keyless Remote Fob Reprogramming?


http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html

----------

After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?

http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html

-----------

Audi A8 Key Fob Programming?


http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html

----------------

Oldsmobile Aurora Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html

-------------

Buick Lesabre Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html

---------------

Keyfob remote not working on 2003 Ford E350 Econoline?

http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html

-----------

KeyFob will open the doors but not start on BMW?

http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html

------------

Mitsubishi Car Key Not getting detected after replacing ECM

http://repairhelpcenter.blogspot.com/2012/11/mitsubishi-car-key-not-getting-detected.html

-----------

Key Fob will not lock and unlock doors?

http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html

-------------

2000 Jeep Cherokee Limited: KeyFob Remote Not Working?

http://schematicsdiagram.blogspot.in/2012/06/2000-jeep-cherokee-limited-keyfob.html

-----------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

-----------

Theft indicator not letting car to start?

http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html

-------------

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html

--------------


These details will help.

Thanks.

Nov 28, 2012 | Peugeot Cars & Trucks

2 Answers

How program the key remot


Keyfob remote reprogramming is not very difficult but on some cases it can be done by dealer service tools.If the remote s faulty then keyfob will not get programmed.Insert the key in ignition.Turn the key to on position,and cycle the key three times off-on-off-on-off-on.Then with the keyfob remote select your remote and then try to operate the vehicle with remote.These is just the basic procedure,but sometimes it will not help.
On that case dealer is the only option.
---------There are few very relted troubleshooting links mentioned below for remote key fob reprogramming.I suggest you to go through the list and click the link below to go through its details and procedure:-------
2009 Toyota Highlander: Smart Key Not getting Detected? http://whatisbyme.blogspot.in/2012/05/2009-toyota-highlander-smart-key-not.html
----------2007 Toyota Prius: Reprogram Remote Keyfob? http://whatisbyme.blogspot.in/2012/05/2007-toyota-prius-reprogram-remote.html
----------- Pin that holds the flick key part to the key fob? http://whoisbyme.blogspot.in/2012/07/pin-that-holds-flick-key-part-to-key-fob.html
-------------
2006 Toyota Hilux: Programming New Key? http://technoanswers.blogspot.in/2012/04/2006-toyota-hilux-programming-new-key.html
----------Where is Key chip memory located on 2004 ford Freestar? http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html
----------Ford Keyless Remote Fob Reprogramming?


http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html
----------After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure? http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html
-----------Audi A8 Key Fob Programming?


http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html

----------------
Oldsmobile Aurora Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html

-------------
Buick Lesabre Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html

---------------
Keyfob remote not working on 2003 Ford E350 Econoline?

http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html

-----------
KeyFob will open the doors but not start on BMW?

http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html

------------
Mitsubishi Car Key Not getting detected after replacing ECM http://repairhelpcenter.blogspot.com/2012/11/mitsubishi-car-key-not-getting-detected.html
----------- Key Fob will not lock and unlock doors?

http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html

-------------
2000 Jeep Cherokee Limited: KeyFob Remote Not Working? http://schematicsdiagram.blogspot.in/2012/06/2000-jeep-cherokee-limited-keyfob.html
----------- Chevrolet Malibu: Key Stuck in ON position? http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html
----------- Theft indicator not letting car to start?

http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html

-------------
2012 Dodge Ram: Ignition Key will not release? http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html
--------------
These details will help.Thanks.

Nov 23, 2012 | 2006 Toyota Tacoma

2 Answers

I'm looking to buy a 1994 Ford Taurus. The owners have 1 ignition key, but no door keys and no key fobs. How you loose these, I have no idea! How do I get replacement door keys and remotes? Are these...


Ford can cut a key with the vin#. As far as the fob, dealerships don't carry them any longer. If you can find one on eBay the dealership can reprogram it but most are too lazy and won't bother. Google "replacement key fobs", there are a few companies that sell
Replacements and can program them for you. Pep boys and auto zone also carry replacements but I'm not sure about the programing. Good luck.

Mar 06, 2011 | Ford Taurus Cars & Trucks

1 Answer

Remote key fob won'tprogram


1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works

Aug 13, 2009 | 1999 Ford Escort

2 Answers

Keys stolen including remote entry ,, door/ignition key .. what do I do


Dealer can Reprogram it in a Way that Old FOB Will NOT Work

Aug 07, 2009 | 2002 Jeep Grand Cherokee

2 Answers

Key fob not working after battery change ford focus 2006


Try reprogramming it.

1. Turn the ignition from OFF to RUN 4 times within 6 seconds.
2. Turn the ignition OFF. The system will chime to confirm programming mode.
3. Within 20 seconds, press any button on first keyless remote.
The system will chime once to confirm programming.

4. Within 20 seconds, press any button on second keyless remote.
System will chime once to confirm programming.

5. Turn ignition to RUN to exit programming mode.

May 28, 2009 | 2006 Ford Focus

4 Answers

Program a remote key for 03 A6


I have an A4 and did this to re-program my key:

1. used the key to start the car...then turned it off
2. put the key in the driver door (door closed)
3. pressed the lock button on the key fob once
4. turned the key to lock the door.

This is basically the steps in the owners manual, but the car must be started with the key first, and the key must be in the door lock before pressing the lock button.

Dec 10, 2008 | 2003 Audi A6

1 Answer

How do i reprogram my02 ford focus remote locking key fob please.


get in your car close door hit the unlock button then put key in the ignition cycle the key from off to on (STOP BEFORE START POSITION) cycle key off to on 7 times after the 7th trime the doors should lock the unlock automatically that means u are in trainning mode hit the unlock button on key fob. the key fob should now work if it doesn't then try changing batt

Nov 27, 2008 | 2001 Ford Focus

2 Answers

Peugeot 406 central locking


you need to reprogram the fob

Sep 07, 2008 | 2006 Peugeot 604

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

389 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...