Question about Cars & Trucks

Open Question

I need to remove my front bumper ford falcon ba

I need to remove my front bumper to replace headlights how do I get the bumper off

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: How do I replace xc90 headlight assembly?

its really easy. Open the hood, you will see two metal flat bars on the backside of each headlight, holding the headlight assembly on. Pull up on each of them.... remove headlight. Ta da.

Posted on Sep 25, 2008

Fleetw00d
  • 31 Answers

SOURCE: Bumper cover removal

It is a little more complicated than that. There are two nuts below the headlight assemblies in the engine compartment. You will need to remove the battery and overflow bottle to get at the one on the passenger side. Remove the turn signals in the bumper, then there are 2 or 3 bolts holding a mounting bracket behind the each of the turn signals. There are a number of bolts with washer heads and reatiners on the underside of the bumper as the previous responder indicated.

Posted on Jan 26, 2009

  • 12 Answers

SOURCE: How to Remove the Rear Bumper - BA Fairmont/Falcon

Firstly, you need to remove the rear splash shields from within the rear wheel arches and also the tail lights. Then remove the scrivets from the lover edge of the bar. Next remove the scuff plate at the boot opening and fold the carpet back. There are four nuts which hold the bar on, undo these and then lift the sides of the bar up and pull out. The bar has large clips on the side which hold it in place.

Posted on Aug 22, 2009

nyrtist
  • 5 Answers

SOURCE: I neede to remove the

Here's some instructions for removing bumper and headlights.

E-Class W211 front bumper removal (standard body style).

Tools needed:
- Automotive wheel ramps (Rhino ramps from Autozone).
- 1/4" drive socket set with 8mm and 10mm sockets.
- #20 torx bit.
- Floor jack, optional but useful.
- Flat blade screwdriver.

Instructions for bumper removal:

1) Turn front wheels full right to remove push-pin fastener at lower front corner of left wheel well plastic splash guard. It's difficult to remove this fastener once the car is up on the wheel ramps.

2) Turn front wheels full left to remove push-pin fastener at lower front corner of right wheel well plastic splash guard.

3) Drive car up on wheel ramps. Block rear tires. Open hood.

4) Remove lower mesh plastic grille. There are five attachment points on the top edge of the grille. You can get to three of them with your hand by reaching between the radiator and the back side of the grille. The two outer ones can be released with a screwdriver also reaching in between the grille and radiator. Once the plastic tabs are released, you can remove the grille by pulling it out from the front of the car.

5) Remove the plastic panel located immediately behind the bumper from the bottom of the engine compartment. This panel is held in place with nine sheet metal screws with a 8mm hex head. Five screws are on the bottom of the car and there are two screws in each wheel well at the inner lower edge. After removing all nine screws you can work the panel free.

6) Disconnect the cable from each fog light and remove both fog lights. They are held in place by two sheet metal screws with a #20 torx head.

7) Remove the side marker bulbs. The one on the passenger side turns clockwise to remove and the one on the driver side turns counter-clockwise.

8) Remove the temperature sensor from its socket on the driver side.

9) If you have a floor jack, raise the car at the jack point on the cross member below the engine. You do not want to raise it off the wheel ramps. But it helps to have more clearance above the tires to work in the front wheel wells.

10) Remove three of the plastic nuts holding the forward half of the plastic wheel well liner in place. It's not necessary to remove the plastic liner. You just need to loosen it up so that you can pull it away from the fender to gain access to the screw and bracket securing the bumper to the fender.

11) Pull back the wheel well liner and remove the sheet metal screw from the rear end of the metal bracket . There is only one sheet metal screw (#20 torx head) holding this bracket in place. Don't attempt to remove the bracket yet. I used a #20 torx bit in a 1/4" socket with a 6-inch extension for a 1/4" drive wrench. The head of the screw faces the ground.

12) Remove the 5mm bolts (8mm hex head) holding the bumper to the headlight assembly between the small lens and large lens (both sides).

13) Remove the two 6mm bolts (10mm hex head) on either side of the large grille area opening.

14) Remove the two 6mm bolts (10mm hex head) securing the bumper to the bottom edge of the crashbar. You can access these bolts through the front where you removed the plastic mesh grille.

15) Remove the three 5mm bolts (8mm hex head) holding each headlight assembly in place. Two longer bolts are on top. One at the rear outer corner and one at the front inner corner. The third bolt is accessed from the bottom. It's in the area above the fog lamps. You don't need to disconnect the headlight cables and remove the assembly. But it helps to allow the headlight assembly to "float" freely while you disengage the bumper from the fender.

16) At this point all of the fasteners holding the bumper in place have been removed. The only thing left to do is to remove the two brackets "clamping" the bumper cover to the lower front edge of the front fenders. Before you do this, position some cardboard boxes, bags of packing material, six packs of paper towels, or other suitable items to protect the bumper in case it falls off the car.

17) The bracket holding the bumper cover to the fender has a "pin" that slips into a slot at the front edge of the bumper cover. There is a matching slot near the front edge of the fender. It's not possible to see this pin from the bottom of the car. Use a flat blade screwdriver to pry the bracket away from the bumper/fender and towards the center of the car. The bracket will "hinge" on the pin at the front end of the bracket. After you swing the bracket away from the bumper, you need to slide it forward to remove it from the slot in the bumper cover and fender. You will probably scratch some paint off of this bracket with the screwdriver. I recommend repainting the scratched areas of the bracket before reinstalling it.

18) After removing the bracket from each side of the car you need to deal with the small plastic "hook" holding the bumper cover to the very front tip of the fender. This hook is an integral part of the bumper cover. Disengaging this hook from the fender is probably the most difficult step of removing the bumper. Simultaneously raise the head light assembly slightly, push the leading edge of the fender outward slightly, and push the bumper cover inward toward the headlight assembly. Don't get too aggressive with the fender. It's aluminum and you will make a real mess if you apply too much pressure on the fender. It took me about 20 minutes to free each side from this hook. It should take you less time, since you now know that the hook exists!

19) Gently pull the bumper forward and away from the car. This is one step where a second person would be helpful. But I did manage to do this step alone. There is a "pulley" like attachment point on each side just below the fender/bumper seam.

To re-install the bumper, reverse the order of the steps above. When re-installing the bracket between the bumper cover and fender, I smeared a thin coating of car wash soap on the bracket to facilitate snapping the bracket back into place.




Posted on Oct 09, 2009

  • 24 Answers

SOURCE: need a diagram to change rear wheel bearings

if you are looking for a manual for this car, try this link... http://cgi.ebay.ph/Ford-Falcon-Ute-BA-series-Repair-Manual-2002-2005-on-CD_W0QQitemZ170423275380QQcmdZViewItemQQptZAU_Clothing_Merchandise_Media?hash=item27ae04cf74 For twenty bucks you can do it all yourself

Posted on Feb 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a drivers side mirror assembly on a BA Falcon XR8?


John, We do not have this model in North America. I did a search and will put links below. "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
http://www.fordmods.com/ford-interior-f14/how-to-remove-the-right-side-mirror-of-a-ba-t73777.html
fordforums com au
2010 Ford Falcon FG FPV F6 Front Left Door Removal

Jul 03, 2016 | Cars & Trucks

1 Answer

My Falcon seems to take a while to start and I have to press the accelerator as well or it will stall, whats the deal?


My 2004 BA Falcon won't start. Apparently it's low - Fixya

www.fixya.com/cars/t12343045-2004_ba_falcon_start_apparently_s_low
Apr 8, 2012 - Apparently it's low on - Ford 2005 Falcon 4.0 question. ... Ba engine generally is strong, common fault is ecu, if hard starting when cold, pour hot water on computer and it ... If the headlights do not dim or go out, then the battery is likely ok..... Automatic 2004 BA Falcon stalls while driving ... Open Questions:.

My xr6 won't start. Comes up saying immobilized. - Fixya

www.fixya.com/.../t12430461-xr6_start_comes_up_saying_immobilized
Feb 6, 2012 - My xr6 won't start. ... Question about 2005 Ford Falcon 4.0 ... you will get airbag errors popping up for a few weeks then after a while it .... in a while it willstart and run for about 20 seconds, then it dies and won't start. ... Open Questions: ...You may NOT copy or distribute the content that appears on this site ...

Ford falcon sometimes won't start - Ford - Automotive - Whirlpool ...

forums.whirlpool.net.au > Automotive > Ford

WhirlpoolOct 26, 2010 - I have a EF Falcon that has an intermittent problem with starting. ... It might take a minute or 5 minutes or persistent retrying. ... Normally if you wiggle the T-Bar around it will then start. ... motor with a rebuilt unit, I had a remove starter on myalarm, and would use the remote start while using my jack-handle to ... Worst Car You Ever Owned
Jun 1, 2012
LPG conversion problems with stalling - Ford
Jan 16, 2012
More results from forums.whirlpool.net.au

2006 Ford Explorer Engine Stalls While Idling: 24 Complaints

www.carcomplaints.com/Ford/Explorer/.../engine_stalls_while_idling.sht...

Jan 27, 2016 | 2005 Ford Falcon 4.0

1 Answer

How to remove rear axle from 2004 ba ford falcon


Hi there.
Well first jack up the rear end of car then block up the front wheels (front and rear) and put stands under the rear jacking points STILL keeping the pressure on the jack, clamp the rear brake pipe that comes from the body to the rear axle and clamp with a small clamp
but dont tighten to tight remove the flex pipe and also the rear shockers from the axle ,then the spring u bolts and then the hand brake cable from the center adjuster,now it should only leave your tail shaft 4 nuts/bolts.
But why are you removing the rear/axle????

May 04, 2014 | 2005 Ford Falcon

1 Answer

Replaceing 04 ba headlights


Ford ba? Battry side you will have to unclamp the battry & move a bit or possibly remove (hope you have your radio code. Use a mirror behind the light so you can see the clip that holds the globe in. Carefull undoing the clip cause if you bend it you will need to remove the whole h'light which is recomended removeing bumper & you don't want that just for replaceing a globe. If uncertain cheaper just to have mechanic do it.

Jul 05, 2012 | Cars & Trucks

2 Answers

I need a manual for a 2004 Ford Falcon BA Futura


Hello,
Please kindly follow the link below to get the manual you requsted for;
http://fitripdf.com/books/ba-gt-ford-falcon-service-manual-2.html


thank you for using fixya

Dec 19, 2010 | Ford Futura Cars & Trucks

1 Answer

How do you remove a headlight 'assembly' (not the


You have to remove the front bumper cover. Put the car on jack stands (the front) and remove the inner fender plastic. You'll need a long extension and a 10mm socket to remove the nuts and bolts holding the bumper cover in place. Once the cover is off removal of the headlight becomes obvious.

May 15, 2010 | 2000 Ford Escort

1 Answer

How to Remove the Rear Bumper - BA Fairmont/Falcon


Firstly, you need to remove the rear splash shields from within the rear wheel arches and also the tail lights. Then remove the scrivets from the lover edge of the bar. Next remove the scuff plate at the boot opening and fold the carpet back. There are four nuts which hold the bar on, undo these and then lift the sides of the bar up and pull out. The bar has large clips on the side which hold it in place.

Aug 04, 2009 | Ford Fairmont Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...