Question about 2008 Hummer H3

1 Answer

2008 Hummer H3 passenger side tail lamp out.

Replaced bulb and still not working. The turn signal and brake light works but the tail lamp does not come on

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 344 Answers

There could be loose wire at the bulb socket ,A break in a wire, Or a bad ground, Or a short, Best way to have it solve is to take it into a auto eletric shop to be check out,

Posted on Nov 28, 2012

  • Lee Menapace Nov 29, 2012

    thanks. I took it to a shop today. It just turned out to be a blown fuse

×

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

carputers
  • 255 Answers

SOURCE: 2008 Hummer H3 The trackion failed light on

clean abs sensors at each wheel.

Posted on Sep 08, 2009

  • 1 Answer

SOURCE: 2006 H3 Hummer rear passenger turn signal non-op.

I have the same problem.help please

Posted on Sep 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear park lights keep blowing fuse


first mistake you make is to increase the fuse capacity to above that required. You have a short in the circuit and by putting such a large fuse in you run the very real risk of burning the wiring loom. Check the bulb sockets and check that the right bulbs are in the sockets. bulbs come in two styles. one has 2 contact points and is either for 2 filaments (stop and tail) or a earth wire (Plastic light units) and the other is a single contact that earths out through the metal base . If you have the wrong bulb in place the current will short directly across the contacts and the light will not come on and the fuse will blow. Fuses for tail lights will be 5 amp maximun

Dec 31, 2013 | 2008 Hummer H3 Alpha

2 Answers

1999 Chevy Malibu driver side tail light won't come on.


I would say that the tail lamp isn't plugged in but- if it is follow the wiring from the tail lamp forward there must be a break in the wiring -maybe someone cut the wires to patch in towing lights - cheers Denny

Nov 27, 2013 | 1999 Chevrolet Malibu

2 Answers

2006 H3 Hummer rear passenger turn signal non-op. Replaced bulb -same also checked fuse - same. need another avenue to check.


Did you check hazard operation, what is the turn signal on dash blink rate(faster than other side)? Make sure socket is clean of corrosion and terminal pins not burnt.

May 11, 2011 | 2006 Hummer H3

1 Answer

Change out a taillight


You want to change the tail light bulb?

The process for replacing tail light bulbs is the same in all models. If you have a burnt-out tail light bulb, you may need to replace the brake light, the reverse light or the turn signal. The procedure to replace each of the bulbs is the same.



    Instructions

    1. Open the Hummer's rear swing gate. This will expose the edge of the vehicle's tail light assembly. You'll see two small Phillips head screws that hold the tail light assembly in place. Put on your gloves.

    2. Remove the two screws from the tail light assembly. Pull the tail light out and inspect the back for two bulbs. The top bulb is the brake light and turn signal. The bottom bulb is the reverse bulb. Determine which bulb you need to replace.

    3Rotate the bulb's socket counterclockwise to disconnect it. Unplug the bulb from its socket.

    4Push the replacement bulb into its socket firmly. Insert the socket back into the tail light. Turn it clockwise to secure it in place.

    5Place the tail light into its cradle. Hold it with one hand and replace the Phillips head screws with the other.

Dec 03, 2010 | 2008 Hummer H3

2 Answers

Tail lights work on both sides. turn signal and


Sounds like you need to replace the drivers brake/tail light.

Dec 14, 2009 | 1998 GMC Sierra

2 Answers

I cant figure out how to open the tail light to replace it


open the tailgate- remove the two screws on so that the tail light can slide out. Turn the bulb assemble and remove the bulb. Replace it and slide the lense back in replace the two screws and your done.

Jul 04, 2009 | 2008 Hummer H3

1 Answer

2006 Ford Ranger. Rear passenger side tail light


Bad earth connection.Clean or replce wire.

Jun 18, 2009 | 2004 Ford Ranger

1 Answer

How to remove passenger side rear tail light lens on 2008 H3 humr


With the car off. Put the park brake on and put it in reverse. When the light comes on take a test light and see witch wire has power.

Apr 15, 2009 | 2008 Hummer H3

Not finding what you are looking for?
2008 Hummer H3 Logo

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...