Question about 1999 Dodge Ram 2500 4WD

1 Answer

I can't find the ckp sensor on my 1999 dodge ram 2500 4/4 5.9L

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Dodge Master
  • 14,384 Answers

Click here Jim to see repair guide.

Posted on Nov 28, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2003 dodge ram with a 4.7. I am getting code p0335 crankshaft position sensor A.

code p0335 refers to crankshaft position (CKP) sensor --circuit malfunction====causes ---wiring---ckp sensor ---ecm
you have checked the wires from ecm connection to sensor connection and eliminated the wires and connections so that only leaves a problem ECM
try substituting the ECM with a known good unit and see it the code is eliminated

Nov 05, 2016 | Dodge Ram Cars & Trucks

1 Answer

100 amp alt fuse

remove serpentine belt. inside the crank pulley there is a large bolt. removal is usually done with a impact wrench. behind the balancer is your crankshaft sensor (CKP sensor.)

Nov 14, 2013 | 1996 Dodge Ram 3500 Club Cab

1 Answer

2002 dodge ram quad 4.7L 2wd abs & brake lights stay on...speedometer & odometer not working, engine light came on code p0500, changed rear speed sensor twice.( I did notice some metal shavings on...

the speedo and odometer are both worked from the VSS ( (vehicle speed sensor)
check for the reason of metal on the sensor end
could have an internal problem that is not allowing the shifting down so have the transmission check out bat an accredited transmission shop

May 22, 2017 | 1999 Dodge Ram

1 Answer

A week ago my dodge ram 1999 5.2l 4 wheel drive lost it's abilitiy to speed up properly. it goes pretty slow as there are no power. By the time I get to 30 miles an hour, I've gone 3 blocks. when I...

Clogged Exhaust Converter --put money on it

Clogged Gas Filter-- maybe --- if in there over 6 years

Tps Sensor-- at least have it checked out

O2 Sensors -- most likely worn out & not controlling
fuel trim

Going to assume you know about the spark plugs,rotor,cap
air filter etc..& no chip monks took up home in the air filter box

Never by pass the battery voltage & alternator output & alternator
diode problems putting out A/C voltage

Sep 20, 2011 | 1999 Dodge Ram

1 Answer

1999 dodge ram van speed sensor wiring diagram. I put a new sensor in and it still doesn't work is there a fuse or something else I'm missing

ive run into this a few times, its a bad cluster or if theres a speed sensor on the rear diff then replace that also and see if that works. i had a few of these with the same problem and replace speed sensor in the trany and still no speedo and then replaced the rear diff sensor for abs on the top of the rear diff and that solved the problem.

Jun 15, 2011 | 1999 Dodge Ram

1 Answer

Which o2 sensor is the no. 2 on a 1999 Dodge Ram 1500 with a 5.2

it is the one behind the catalytic converter, furthest from the engine. It only monitors the condition of the cat and does not affect the engine computer and it's ability to monitor engine sensors.

Jun 02, 2011 | 1999 Dodge Ram

1 Answer

2001 dodge cummins 5.9 24v fault code P1690


Sep 07, 2010 | 2001 Dodge Ram 2500 Truck

1 Answer

1999 4x4 dodge ram abs light &brake light has been on about a week. brake fluid &brakes are good. any suggestions

If you lose the speedometer, replace the rear differential speed sensor on top. If the speedo is ok, then it's your ABS pump/solenoid unit in the engine compartment left rear side. Most of the 99's have only the rear ABS, not front so don't look at the front brakes for the issue.

Aug 16, 2010 | 1999 Dodge Ram

1 Answer

Sputtered & died

this happened to me on my 1999 dodge ram and it ended up being the fuel pump

Apr 08, 2010 | 1996 Dodge Ram

1 Answer

How to change crank sensor?

The Crankshaft Position Sensor (CKP) is mounted into the right-rear side of the engine block.

5.2L & 5.9L
The Crankshaft Position (CKP) sensor is located near the outer edge of the flywheel (starter ring gear).

3.9L, 5.2L & 5.9L

  1. Remove right front tire and right front wheelhouse liner.
  2. Disconnect crankshaft position sensor pigtail harness from main wiring harness.
  3. Remove two sensor (recessed hex head) mounting bolts.
  4. Remove sensor from engine.

  1. Disconnect CKP electrical connector at sensor.
  2. Remove CKP mounting bolt.
  3. Carefully twist sensor from cylinder block.
  4. Remove sensor from vehicle.
  5. Check condition of sensor O-ring.

Mar 04, 2010 | 2001 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides