Question about 1993 Chevrolet G30

1 Answer

Fuse panel The third tail light is not working and I need a diagram of the fuse panel in order to check the fuse for this light so the van will pass inspection.

Posted by on

  • 2 more comments 
  • chevyblueang
    chevyblueang Nov 28, 2012

    Thank you for your replies. I have found the fuse panel. Brake fuse was very easy to see. I checked it, and it looked good. Service station had checked the bulbs and said it is not a bulb issue. So, now it is not a bulb or fuse issue. Will have to look deeper. Hopefully not too much deeper. Will pull out the tester tonight to check and see if the socket is getting power. Might have to shop around a bit to find that part, if in fact it is the problem.

  • chevyblueang
    chevyblueang Nov 28, 2012

    I have 3 days to fix this!!!

  • chevyblueang
    chevyblueang Nov 29, 2012

    Used the tester, and it shows no power getting to the bulbs. Didn't notice this problem before today--and hubby follows me driving in his car from time to time. He would have noticed. It seems kind of fishy to us that it was working fine until today, but could be a coincidence of timing. Still, the problem is there, and we need to figure this puzzle out. Any experience with this??? Thanks!

  • Lissa Wied Nov 29, 2012

    Check for loose wires at the bulb sockets, A break in the wires, A loose ground wire, Corrosion in bulb sockets ,Or get a new bulb socket end try it, If all that doesn,t work take it in to a auto electric shop to be repaired (Properly)

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 344 Answers

If the other brake lights work it is not a fuse, They are all control buy one fuse,The bulb is burn,t out,

Posted on Nov 28, 2012

  • chevyblueang
    chevyblueang Nov 28, 2012

    Thanks for your answer. Service station worker thought it could be the bulb. They tried a bulb, and it didn't come on.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1999 Chevy Express Van tail light bulb replacement

Yes, you can replace just the bulb. Remove the light assembly and you can get to the bulbs on the back side.

Posted on Aug 22, 2008

  • 840 Answers

SOURCE: Venture Van - Fuse panel diagram

you need to call the gm part department and ask for a fuse diagram they can print you out one so you can keep it wwith your vehicle. Please rate my response thak you very much

Posted on Jan 28, 2009

SOURCE: Tail lights don't work on 1998 Chevy Silverado.

check the wiring from the tailights back to the fuse panel, it sounds like an open connection. if i recall correctly check under the dash on the drivers side near the fuse panel for a bunch of wires in a bundle and look carefully for a wire or two that are cut/shorted/or seperated, you can also check under the drivers side kick panel by the hood release.

Posted on Feb 17, 2009

  • 14585 Answers

SOURCE: Brakes Lights dont work on a 2006 Chevy Silverado

I've worked on these the first drove me crazy. its the turn signal switch every thing runs thru these. head lights, turn signal, brakes. except the third brake light. it runs directly from the brake switch. go figuare

Posted on Jun 22, 2010

  • 1 Answer

SOURCE: I need a diagram of fuse box for 2000 Chevy Express Van

i have a 2000 Chevy van where is the fuse for the two(2) rear power outlets

Posted on Apr 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a fuse box diagram for a 1985 1.3 Opel Kadett Cub


I found these on a site I'm assuming they're in order from number 1
Layout Diagram Parts: Direction signal lamps, Right tail lamp, license plate lamp, instrument lights, Left tail lamp, Interior lamp, Heater motor, stop lights, Horn, windshield wiper
if the fuse is good and the wires are not broken or disconnected it may be the wiper motor is bad

Feb 18, 2015 | Opel Cars & Trucks

1 Answer

I have an Australian delivered 2004 Ford Exployer. My Brake lights are not working, but my Tail gate brake light is funtioning.I have misplaced my owners manual and only get descriptions of the fuse panel...


Chances are its not a fuse. The brake lights get power thru the brake switch. But the third brake light does not pass thru the turn signal switch.
So if it works but the regular brake lights do not, the problem may be in the turn signal switch.

Feb 17, 2015 | 2004 Ford Explorer

1 Answer

2000 Lexus LS400 Instrument panel fuse


It's more likely a fuse is blown, the tail lights are on the same fuse as the dash illumination, check the tail lights if they are not working replace the fuse marked 'tail' in the fuse panel on the inside at the left side of the dash under the cover. At the same time check the 'gauge' fuse', there is a fuse location diagram on the cover.

Apr 13, 2014 | 2000 Lexus LS 400

1 Answer

1998 Nissan Sentra: A) Service Engine Soon Codes; and B) Tail Light Wiring Question...


First, the wires you plucked from the rear lights may be ground wires that corroded and fell out of their termination, or could be secondary wires that provide voltage to your tail parking lights.. and if you touched them to somewhere that had voltage going to it, which it sounds like what happened if sparks flew (or you may have touched a live wire to a ground), you may have sent a voltage spike that blew the dashboard lights out. Did you check all the fuses after the seeing the sparks?? I would suspect that you blew a fuse when that happened. What you need to do is get a volt meter to determine if the loose wires have voltage going to them when the light switch is on, or see if they have continuity to ground.. You say the brake lights work but not the tail lights, so maybe those loose wires either supply voltage to the tail lights, or could be the ground wires for the tail lights. A meter will let you know if they either have voltage going to them or if they have continuity to ground. If you don't know how to do this, you should let someone who knows what they're doing check the wires as you may cause even more damage if you don't know what you're doing.......... I didn't look up your engine codes, but if you have one that has MAP/BAR , it could be that your MAP (manifold absolute pressure) sensor is bad. This will definitely cause the gas mileage to drop and could cause the engine to run bad..You need to have this vehicle checked for vacuum leaks too. Being that it's an older car, you could have cracked hoses or collapsed hoses causing a vacuum leaks which could also trip the MAP/BAR engine code. If your gas mileage is that bad, it sounds to me like the engine could use a good tune up. Replace air filter and PCV valve, plugs/wires etc. Check for bad or dirty sensors, vacuum lines etc need to be checked...You can have the codes cleared from the computer, but once you do that, the computer will just send the same codes and trip the check engine light again if you do not find and fix the problem causing this condition. Even when you repair the problems, the car will need to be driven for a bit before the computer will allow all the emission parameters to reset and then give you the green light to have the car inspected. Simply clearing the codes without fixing the problems will not allow the vehicle to pass an inspection. The computer needs to reset after the repairs have been done, and then you can take it in for an inspection..Sorry I can't be of more help, but this should give you somewhere to start..Have a look at your vacuum lines, clean or replace the MAP and MAF (mass air flow) sensors (there are you tube vid's on how to do this) and get a meter to see if those loose wires have voltage to them or if they have continuity to ground. Then maybe you can figure out where they came from. I suspect they may have pulled out of a rear light wiring harness connector or a light bulb socket. Good luck!

Feb 27, 2017 | Cars & Trucks

1 Answer

No tail lights


You should have a fuse panel under you dash inside. This is where the fuses are located for lights. Don't know the exact location, but you can pull each fuse to see if it is bad. This won't hurt anything. It just keeps you from hunting down a diagram of where the fuse is located.

Apr 20, 2010 | 2008 Scion Xb

1 Answer

2003 Sienna tail lights don't work when headlights are on


Look under the dashboard, next to/above the park brake pedal, for the interior fuse box. It has a black plastic cover. Remove the TAIL fuse, and see if it is blown. This should get you fixed up. Hope this helps, and Thanks for choosing FixYa.

Nov 11, 2008 | 2008 Toyota Sienna

1 Answer

1999 Chevy Express Van tail light bulb replacement


Yes, you can replace just the bulb. Remove the light assembly and you can get to the bulbs on the back side.

Aug 12, 2008 | 1999 Chevrolet Astro

Not finding what you are looking for?
1993 Chevrolet G30 Logo

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...