Question about 2000 Jeep Grand Cherokee

1 Answer

Left turn signal stops working

Left turn stops working ,changed turn signal switch ,same thing, Turn 4-way switch on&off signal starts working agian

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Had simular problem with wife 2000 Jeep Cherookee.
My signal light were not working at all.Check flasher relay under steering colum

Posted on Nov 30, 2012

  •  Gene Dawson
    Gene Dawson Nov 30, 2012

    Thank you Ramon , changed flasher works fine

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1998 wrangler turn signal/brake light short

your socket may not be grounded properly, I have seen this before, and the simplest way to fix is change the socket with a new one.Not another used one it may also be bad.

Posted on Sep 06, 2008

  • 1 Answer

SOURCE: turn signals

replaced turn signal flashers and muti switch turn signal still won't work Why?

Posted on Nov 11, 2008

  • 840 Answers

SOURCE: Turn signals quit working

one of the bulbs is not working soneither ill work so you need to check both bulb check the rear first its the easiest 2 screws inside rear and pull out light

Posted on Jan 25, 2009

  • 5 Answers

SOURCE: Left turn signal stops flashing when brake pedal is depressed.

there is a ground problem, most likely in the tail unit itself, but a ground problem is hard to find and easy to fix. reground the system, the turning unit, and the problem should stop. About the hazards, I don't know...... some times in older cars, that is the way it works. because the brake and hazard element in the bulb is the same and the old cars used a break in the power, but the new cars use a break in the ground. any way, chase the ground down first, it is usually the cause.

Posted on Feb 12, 2009

  • 141 Answers

SOURCE: left rear turn signal and brake light dont work

You have a broken wire to the turn/brake light portion of the light as they use the same wire. Or where the plug goes into the light assy could be bad. Torsion mount lights are horrible and you should think about replacing with a universal light that you can wire direct.

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my 2008 chevrolet uplander's turn signal does not making clicking sound , but the signal lights are working.


Did you put a aftermarket radio in ? The clicking sound comes out the driver side speaker . It's generated by the BCM body control module .
Turn Signal Lamps
The STOP/TURN fuse in the instrument panel (I/P) fuse block supplies battery positive voltage to the body control module (BCM) for the turn signal lamps. When the turn switch is placed in the left or right position, ground is applied to the BCM on the left or right turn signal switch signal circuit. The BCM then applies voltage to the appropriate front and rear supply voltage circuits.
Grounds for the various lamps are as follows:
• G100 supplies the right front lamps
• G101 supplies the left front lamps
• G400 supplies the right rear lamps
• G401 supplies the left rear lamps

Your best bet would be to take it to a qualified repair shop before you start replacing parts , like the BCM ,which would need to be programmed at the dealer or other thing's will stop working too .

Aug 30, 2017 | Chevrolet Cars & Trucks

1 Answer

What would cause the turn signal to blink continuously?? The only time the left one stops blinking is when you use the right signal??


sounds like the turn signal switch in faulty.
i found some great info that explains the switch and its functions.


Self Canceling Signals How Turn Signals Work

(page 4)
Cheers!

Oct 30, 2014 | Cars & Trucks

1 Answer

Problems with 2004 GMC Sierra Z71 left turn signal


The turn signal / hazard flasher module is the problem ,more then likely . Without testing this is just a guess . Do you know how to do automotive electrical circuit testing using a wiring diagram an a DVOM - digital volt ohm meter . Plus factory service repair manual flow charts .
The IGN E 10-amp fuse in the underhood fuse block supplies battery positive voltage to the turn signal/hazard switch assembly. The FLASH 25-amp fuse in the instrument panel (I/P) fuse block supplies battery positive voltage to the turn signal/flasher module and ground is supplied at G200. When the turn signal switch is placed in either the LEFT or RIGHT position, a voltage signal is completed from the turn signal switch to the turn sign/flasher module. When the hazard flasher switch is activated, a ground signal is completed from the turn signal/hazard switch to the turn sign/flasher module. The turn sign/flasher module then sends an on-off voltage signal through the LT TRLR, RT TRLR, LT TURN or RT TURN 10-amp fuses in the I/P fuse block to the appropriate turn signal or to all 4 fuses for hazard operation. The instrument panel cluster (IPC) indicators receive voltage from the LT TURN and RT TURN fuses as well as the driver door module (DDM)/passenger door module (PDM) for the mirror turn signals. The DDM/PDM has no function or control of the mirror turn signals other that a pass through connection for the circuits. The audio chime is also activated when the turn signals are ON. When the hazard switch is pressed, all turn signal lamps will flash including both IPC turn indicators. The front turn signals are grounded at G100. The rear turn signals are grounded at G401. The Mirror turn signals are grounded by the DDM/PDM.

Jan 07, 2018 | Cars & Trucks

1 Answer

How to change the turn signal switch on a 1995 gmc suburban


The turn signals (left & right) have stopped working on my 95 suburban. Is this a fuse or do I need a new switch?

May 23, 2012 | 1995 GMC Suburban

1 Answer

Turn signals do not work but everything else works even the emergency flashers


I have found a lot of these turn signal switches bad but check fuse 27 if ok This is a tip turn key one and put turn signal switch in the left or right postion, then push and release the 4 way switch at least 10 times if at any time the turn signals start working while the 4 way switch is off the turn signal is bad. What happens is the contacks in the switch pit and buy working the 4 way switch a bunch of times it scraps through the pits. If they do start working change the switch this isn't a fix its just an easy way to pin point a common problem. If that did work here are the complete test.

326caaa.png7954492.pngc51c094.png48332bd.png

Oct 20, 2010 | 2002 Ford F250 Super Duty SuperCab

1 Answer

The left turn signal stopped working, then the right. Now the blower and the abs light is on. I changed the turn signal switch/hazzerd/wipers. And the 10 amp fuse keeps blowing. Marked turn/bu/abs


20amp turn on four ways and parking lights go around replace any bad bulbs turn of for ways tern key on tern right tern on go around se if blinking tern on left and se if not chang flash thears 2 flashers switch the tow to se witch is bade.chek fuse for the right amp look inside fuse cover for right amp

Jan 26, 2010 | 2000 Dodge Caravan

2 Answers

Turn signals hazards flasher don't work jeep cherokee replaced combination flasher relay, turn signal switch and still no signals


I NEED TO LOCATE THE SWITCH WHERE IS IT ?
MY INDICATORS NOR HAZARD LIGHTS ARE WORKING I DONT KNOW WHAT IS WRONG WITH IT CHANGED BULBS BUT NOTHIGN THEY ALL WENT OUT AT THE SAME TIME
SO THERE MUST BE A RELAY SWITCH SOMEWHER BUT DONT KNOW WHERE ?
THANKS FOR HELPING

Sep 27, 2009 | 1999 Jeep Cherokee

1 Answer

1998 Cavalier rear turn signal doesn't work


The turn signal switches are known to go bad, try to use the turn signal switch and jiggle the lever after clicking to the left turn. Replace signal switch assembly.

Jul 19, 2009 | 1998 Chevrolet Cavalier

3 Answers

Turn signals


replaced turn signal flashers and muti switch turn signal still won't work Why?

Nov 08, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

79123 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...