Question about Jeep Liberty

Open Question

Jeep cherokee crd 2.5 2002 timing belt diagram

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
whispers76
  • 55 Answers

SOURCE: serpintine belt

This link will take you to a picture of the diagram. If the link doesn't work contact me and I can email you the picture directly.

http://autorepair.about.com/library/illustrations/bl506a-lib.htm

Posted on Jan 10, 2009

Ad
  • 1 Answer

SOURCE: Belt routing diagram for 1990 jeep cherokee with 4.0 engine

I did not get it solved, but that's okay .I will try for it another way. Those passwords that you gave me , i couldn't get to work. I have appreciated your time and patience. Thanks very much.
Charles Thigpen

Posted on Jan 19, 2009

  • 6982 Answers

SOURCE: 2000 jeep grand cherokee 4.0 liter engine timing belt replacement

If you have the same pulley arrangement that most 4.0 engines have that pulley is an idler not a tensioner. Your power steering pump has a pivot bolt, and a slide under the pump. You adjust belt tension using the pump.

Posted on Apr 05, 2009

MNfisherman
  • 11896 Answers

SOURCE: serpentine belt on a 1995 jeep grand cherokee

let me know if this looks correct. If not I will find another diagram. Available at google images

b180d86.jpeg

Posted on Nov 15, 2009

ZJLimited
  • 17970 Answers

SOURCE: jeep grand cherokee 2.7 crd

DTC P0243 - Turbo/Super Charger Wastegate Solenoid A
Description: Open or shorted condition detected in the turbocharger wastegate solenoid control circuit.


Here is the flow chart for that code (some images could need to clicking for zoom)...

P0243-WASTEGATE PRESSURE CONTROL PWM

zjlimited_337.gif

For a complete wiring diagram Refer to Section 8W.

When Monitored: When the ignition is on.
Set Condition: The ECM detects an open or short circuit in the Wastegate solenoid circuit.

Possible Causes
DAMAGED WIRING HARNESS OR CONNECTORS
WASTEGATE SOLENOID
(F504) FUSED IGNITION SWITCH OUTPUT OPEN
(K139) WASTEGATE SOLENOID DRIVER CIRCUIT OPEN
(K139) WASTEGATE SOLENOID CIRCUIT SHORTED TO GROUND
(K139) WASTEGATE SOLENOID DRIVER SHORTED TO VOLTAGE
(K139) WASTEGATE SOLENOID DRIVER CIRCUIT SHORTED TO ANOTHER CIRCUIT
ECM
INTERMITTENT CONDITION

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)

Diagnostic Test
1. DAMAGED WIRING HARNESS OR CONNECTORS

zjlimited_338.gif

Turn Ignition off.
Disconnect the ECM harness connectors.
Disconnect the Wastegate Solenoid harness connector.

NOTE: Check connectors - Clean/repair as necessary.


Are any wires or pins damaged?

Yes
Repair or replace any damaged wire or connectors.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).

No
Go To 2


2. WASTEGATE SOLENOID

zjlimited_339.gif

Reconnect the ECM harness connector.
Reconnect the disconnected Wastegate Solenoid harness connector.
Turn the Ignition on, engine not running.
Disconnect the Wastegate Solenoid harness connector.
Connect an incandescent test light across the supply and driver pins at the Wastegate Solenoid harness connector.

NOTE: The ECM will perform a self check of the circuit after approximately 30 seconds, which should light the incandescent test light.


Does the light illuminate brightly after 30 seconds of being connected?

Yes
Replace the Wastegate Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).

No
Go To 3


3. (F504) FUSED IGNITION SWITCH OUTPUT OPEN

zjlimited_340.gif

Connect an test light between the Wastegate Solenoid connector Fused ignition switch output circuit and battery negative.
Compare the test light brightness to that of a direct connection to the battery.

Does the light illuminate brightly?
Yes
Go To 4

No
Repair the open (F504) Fused Ignition switch output circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).



4. (K139) WASTEGATE SOLENOID DRIVER CIRCUIT OPEN

zjlimited_341.gif

Disconnect the ECM harness connectors.
Measure the resistance of the Wastegate Solenoid driver circuit between the Wastegate Solenoid harness connector and the ECM harness connector.

Is the resistance less than 10 Ohms?
Yes
Go To 5

No
Repair the open (K139) Wastegate Solenoid control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).


5. (K139) WASTEGATE SOLENOID CIRCUIT SHORTED TO GROUND

zjlimited_343.gif

Measure the resistance of the (K139) Wastegate Solenoid driver circuit between the Wastegate Solenoid harness connector and battery negative.

Is the resistance less than 10 Ohms?
Yes
Repair the (K139) Wastegate solenoid circuit shorted to ground.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).

No
Go To 6


6. (K139) WASTEGATE SOLENOID DRIVER SHORTED TO VOLTAGE

zjlimited_344.gif

Measure the voltage between the (K139) Wastegate Solenoid driver circuit at the Wastegate Solenoid connector and battery negative.

Is the voltage less than 1 volt?
Yes
Go To 7

No
Repair the (K139) Wastegate solenoid driver shorted to voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).


7. (K139) WASTEGATE SOLENOID DRIVER CIRCUIT SHORTED TO ANOTHER CIRCUIT

zjlimited_345.gif

Measure the resistance between the (K139) Wastegate Solenoid driver circuit in the ECM harness connector and all other circuits in the ECM harness connectors.

Is the resistance less than 10 Ohms?
Yes
Repair the (K139) Wastegate solenoid circuit shorted to another circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)


No
Go To8


8. WASTEGATE SOLENOID

zjlimited_346.gif
Reconnect the ECM harness connector.
Reconnect the disconnected Wastegate Solenoid harness connector.
Turn the Ignition on, engine not running.
Disconnect the Wastegate Solenoid harness connector.
Connect an incandescent test light across the supply and driver pins at the Wastegate Solenoid harness connector.

NOTE: The ECM will perform a self check of the circuit after approximately 30 seconds, which should light the incandescent test light.


Does the light illuminate brightly after 30 seconds of being connected?
Yes
Refer to the INTERMITTENT CONDITION Symptom (Diagnostic Procedure).

No
Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).

------------------------------------------------------------------------------------------------------------------------------------------------

Keep us updates.

Posted on May 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Am looking for the diesel pump timing on a jeep grand Cherokee 3.0


no year, stated, 1993 to now.
3.0? 2005?
what county?
what year....??

diesels
2.5L not in usa
3.1L not here
3.0 L Mercedes Benz CRD 05 to 2010, ww.,
3.0 L CRD V6 gen 3, 2011 up ww
a.k.a OM642


no job stated ! "just nebula's timing"
no symptoms stated.
or no DTC errors scanned reported !


om642 v6 runs common rail injection
with
The injection system operates at 1,600 bar (23,000 psi),
there is a lift pump in the tank and a super high pressure pump .
scan the PCM yet.
check fuses
change out fuel filters and bleed out air?


here are some CRD Links. (random but on 642 v6)


http://www.jeepforum.com/forum/f67/2007-wk-3-0-crd-80kmi-etc-cel-p0101-p0088-limp-mode-1443093/index2.html


http://www.jeepforum.com/forum/f67/crd-fuel-pressure-problem-2530618/


$1200 pump usa
$2500 Europe Euro Stage 4 Emission ouch.

i dont have a book, on it, but why would it need to be timed?9fb06357-a7bb-4b90-9bc3-76c13e034589.jpg

Apr 24, 2016 | Jeep Cars & Trucks

1 Answer

Need new tail lights on crd 2008 Grand Cherokee, where can I buy them? and ship to Icelnad


did you all jeep:?
call them all and ask for international shipping.
they all have email. , all, google for Jeep dealer, click parts, click email.

Dec 16, 2013 | 2008 Jeep Grand Cherokee

1 Answer

Show me a diagram for serpentine belts on 1989 jeep cherokee


The belt diagram is contained in a belt diagram booklet put out by DAYCO Corp. Click this LINK to download it, give it time to load, it is a large pdf file.

Feb 13, 2012 | 1989 Jeep Cherokee

1 Answer

I need a 2005 jeep Liberty CRD serpentine belt diagram and which of nine pullies to place the belt on first


belt snapped?, some have diagram under hood, look yet?
ok , i guess you dont have the FSM?
and want us to read ours. is that it>?
https://www.techauthority.com/en-US/Pages/Home.aspx

The USA JEEP LIBERTY IS KJ
that year.
2.8L CRD engine, serp
page 9-165 FSM



6960685-xcqoluy0r3kgpc4qbsqstagz-4-0.jpg

Nov 23, 2010 | 2005 Jeep Liberty

1 Answer

I need a diagram for a 1997 jeep cherokee sport for changing a serpentine belt


1997 JEEP CHEROKEE - L6 4.0L 242ci GAS FI N S
Belt Routing Diagram - Multiple Accessory, w/A.C.

3797af4.jpg



1997 JEEP CHEROKEE - L4 2.5L 150ci GAS FI N P
Belt Routing Diagram - Multiple Accessory, w/A.C.

7759183.jpg

From DAYCO Catalogue.

Hope helped with this; remember rated this help. Good luck.

Nov 18, 2009 | 1997 Jeep Cherokee Country

1 Answer

Loud Intermittent Buzzing Noise Jeep Cherokee Sport 2.8 CRD 2005


I would need to hear this noise to help, sorry, but you need a shop to look into this.

Feb 07, 2018 | 2001 Jeep Cherokee

1 Answer

I have a 2005 jeep cherokee 2.8 crd the key


disconnect the battery or pull the ignition fuse,then replace the ignition

Sep 21, 2009 | Jeep Cherokee Cars & Trucks

1 Answer

2003 jeep cherokee 2.8 CRD engine sqeeking noise


It could be that you got some water on your serpentine belt and that will cause it to squeak. Try buying a can of "belt dressing" from an auto store and spray it all over your belt and see if that will stop it. It's a cheap and easy thing to try before replacing expensive parts. Hope this works for you, let me know how it goes. Goodluck!

May 05, 2009 | 2003 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...