Question about 2005 Cadillac SRX

Open Question

2005 cadillac srx thermostat location - 2005 Cadillac SRX

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.

Posted on Jan 25, 2009

Ad
  • 137 Answers

SOURCE: thermostat location on a 1999 cadillac deville concours

looked it up online and looks like it's on the front of the water pump in a thing called the coolant inlet housing. one end of it looks something like the letter y and the other end, where the thermostat is round. hope that helps

Posted on May 30, 2009

  • 5 Answers

SOURCE: where is the oil filter located on a cadillac srx

Directly under the engine. You'll see a large smooth portion under there that looks like the underside of a bath tub and on the lowest portion of that is a bolt. Thats your oil reservoir where you drain your oil. The filter should be located near that pointing toward the front of the vehicle. GM OEM filters are usually black but could be white and are almost always 3" filters so a filter wrench that fits a 3" filter will get it off without problem.

Posted on Nov 13, 2009

Testimonial: "Thanks forn the help! This info has been hard to find from other sources. Again thanks!"

techbuster
  • 5081 Answers

SOURCE: rear liscese plate bulbs on 05 cadillac srx

First you have to take out the one and only screw in the rear hatch door - it's where the hand pull down is you use to close the hatch.
Then you have to pop all the plastic clips all the way around the plastic door panel, trying not to pull them out from the frame . If you do pull out the white plastic plugs from the frame you better make certain you take them off the plastic housing and insert them back into their frame holes - or you will never get the housing back on.

Once you have the housing loose disconnect the inside tail gate light wire to remove the whole thing. Then you have to remove 7 to 8 nuts from the back of entire License plate, back up bulb housing using a deep socket to get in there. Work it loose from the rear of the car and it will come out just enough to work on the lights.
This is tricky since the screw mounts don't give you much room to work with.

Once you have the license plate and back up bulb frame loose you will see the two housings for the license plate bulbs on top.

Slide out the license plate bulb lens and twist the bulb connection to remove the bulbs.
Replace both of them - you don't want to do this again in a month when the other one blows.

OPTIONAL:
Once you take out the bulbs you might see that the housing is melted where the bulb wanted to burn through. Drill two small holes one is each end of the housing before I put everything back together to release some of the heat.


Reverse the whole process to put everything back together. It's not easy.
Make sure you insert the cables through the opening for the hatch handle or it will kink and not work properly.

The bulbs come in a two pack of cost $4.95 .

Posted on Nov 24, 2009

Sheikhtijani
  • 1284 Answers

SOURCE: how do you replace license

Hi,
First you have to take out the one and only screw in the rear hatch door - it's where the hand pull down is you use to close the hatch.
Then you have to pop all the plastic clips all the way around the plastic door panel, trying not to pull them out from the frame . If you do pull out the white plastic plugs from the frame you better make certain you take them off the plastic housing and insert them back into their frame holes - or you will never get the housing back on.

Once you have the housing loose disconnect the inside tail gate light wire to remove the whole thing. Then you have to remove 7 to 8 nuts from the back of entire License plate, back up bulb housing using a deep socket to get in there. Work it loose from the rear of the car and it will come out just enough to work on the lights.
This is tricky since the screw mounts don't give you much room to work with.

Once you have the license plate and back up bulb frame loose you will see the two housings for the license plate bulbs on top.

Slide out the license plate bulb lens and twist the bulb connection to remove the bulbs.
Replace both of them - you don't want to do this again in a month when the other one blows.

OPTIONAL:
Once you take out the bulbs you might see that the housing is melted where the bulb wanted to burn through. Drill two small holes one is each end of the housing before I put everything back together to release some of the heat.


Reverse the whole process to put everything back together. It's not easy.
Make sure you insert the cables through the opening for the hatch handle or it will kink and not work properly.

The bulbs come in a two pack of cost $4.95 .

Take care

Posted on Jul 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace thermostat on 2005 srx cadillac


I'm not sure which engine you have, this is for LX2

26303959-d5pya0i0sr2gdavxtx1tpvby-5-0.jpg

26303959-d5pya0i0sr2gdavxtx1tpvby-5-2.jpg

Oct 07, 2016 | 2005 Cadillac SRX

1 Answer

How do I lower the backseats in my 2005 Cadillac SRX so they lay flat


Could be a switch under or around the trimming of the seat. if you cant figure it out take it to the dealer they will be happy to help you.

Sep 21, 2014 | 2005 Cadillac SRX

1 Answer

Replacing the fuse for 2005 cadillac srx back up lights


Hello! In the Left Rear Fuse Block is the Reverse lamp fuse (10A)....The Reverse lamp relay is also located in that box...If the fuse doesn't fix it replace the relay...The relay is low cost....$6...See picture below...guru...saailer


12_13_2011_1_08_47_am.jpg
ACDELCO Part # D1755A

Dec 12, 2011 | 2005 Cadillac SRX

1 Answer

How do I replace the battery in my 2005 Cadillac srx?


how to replace the battery in my 2004 cadillac srx

Oct 24, 2010 | 2005 Cadillac SRX

2 Answers

Where is the starter located on a 2005 cadillac srx v 8?


If your SRX has a Northstar V/8 engine the starter is under the intake manifold. The manifold has to be removed to access the starter. Hope this helps, thank you

Sep 04, 2010 | 2005 Cadillac SRX

1 Answer

On a 2005 cadillac srx, v6, how are the cylinder label 1-6?


The firing order is 1-2-3-4-5-6. Cylinders are located on the driver's side front to rear of engine 1-3-5 passenger side front to rear 2-4-6.

Aug 11, 2010 | 2005 Cadillac SRX

1 Answer

How do i chnage the running light on a 2005 cadillac srx


Depending on which side you are working. Here are the steps that I found that works for me.
1. Remove the wheel
2. Remove all inner plastic guards, to include the bottom one
3. Locate the light assembly
4. Remove all Torque Head screws
5. Remove cover
6. Locate light plug and twisted it to remove
7. Replace light
8. Re-install all removed parts
9. Finished
The whole task could take up to 45 minutes depending on SNAFU's

Apr 22, 2010 | 2005 Cadillac SRX

3 Answers

How to tell if water pump for 04 cadillac srx needs to be replaced.


Your car will overheat very fast and you may either notice coolant leaking from the location of the pump and also possibly a squealing noise due to a bad bearing. Overheating can also be caused by a bad thermostat.

Feb 17, 2010 | 2004 Cadillac SRX

Not finding what you are looking for?
2005 Cadillac SRX Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...