Question about 1999 Chevrolet Lumina

1 Answer

1999 lumina 3.1 cam sensor

Do i need to remove the intake manifold to replace the cam sensor

Posted by on

  • raymond41 Jan 15, 2009

    looking for any one who has accualy done the job.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 21,990 Answers

If it looks like its in the way then yes it will need dismantleing

Posted on Jan 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 nissan sentra sx 200 knock sensor location


Melvia, Knock sensor located under the intake manifold between cylinder #2-3 I believe, hard to change with out removing intake manifold, but can be done. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
1995 1999 Nissan Maxima 1 2 Knock sensor replacement
KA24DE Knock Sensor Code 34 FREE REPLACEMENT How To
Knock sensor on 1995 Altima
Get the Best Priced Nissan Sentra Knock Sensor

Aug 21, 2016 | Nissan Cars & Trucks

2 Answers

How to replace a intake plenum gasket


Well basically, you remove the intake plenum and replace the gasket and reinstall the plenum. Here are the steps:

1. Disconnect the negative battery cable from the remote jumper terminal located at the right strut tower.
2. Remove the air inlet resonator and tube.
3. Remove the throttle actuator cables from the throttle arm and bracket.
4. Disconnect Secondary Runner Valve (SRV), Manifold Tuning Valve (MTV), Throttle Position Sensor (TPS), Idle Air Control (IAC) motor electrical connectors.
5. Remove the electrical connector and the Intake Air Temperature/Manifold Absolute Pressure (TMAP) sensor.
6. Disconnect vacuum hoses from the Secondary Runner Valve (SRV) reservoir, Speed Control reservoir, and PCV.
7. Remove right and left intake manifold supports.
8. Remove support brackets at the intake manifold front corners and MTV.
9. Loosen upper fastener attaching throttle body to support bracket.
10. Remove clips attaching EGR tubes to intake manifold.
11. Remove intake manifold bolts and manifold
12. Remove old gaskets, Clean gasket surfaces, and install new gaskets.
13. Reverse steps to reinstall manifold

Jun 16, 2012 | 1999 Chrysler 300M

1 Answer

Where is the MAP sensor on 99 jeep grandcherokee 4.7 L 8 cylinder


On 4.7L the MAP sensor is located on the front of the intake manifold. An O-ring seals the sensor to the intake manifold.

zjlimited_1118.jpg
(click over image for zoom)

  1. Disconnect electrical connector at sensor.
  2. Clean area around MAP sensor.
  3. Remove 2 sensor mounting bolts.
  4. Remove MAP sensor from intake manifold.

Hope this helps.

Apr 27, 2011 | 1999 Jeep Grand Cherokee

1 Answer

How hard is it to replace the MAP sensor on a 2001 dodge durango?


VERY SIMPLE!!!!!

4.7L The MAP sensor is located on the front of the intake manifold. An O-ring seals the sensor to the intake manifold.
  1. Disconnect electrical connector at sensor.
  2. Clean area around MAP sensor.
  3. Remove 2 sensor mounting bolts.
  4. Remove MAP sensor from intake manifold.
To Install:
  1. Clean MAP sensor mounting hole at intake manifold.
  2. Check MAP sensor O-ring seal for cuts or tears.
  3. Position sensor into manifold.
  4. Install MAP sensor mounting bolts (screws). Tighten screws to 3 Nm (25 inch lbs..) torque.
  5. Connect electrical connector.

Apr 23, 2010 | 2001 Dodge Durango

1 Answer

Where do i find the cam shaft and knock sensors for a 1999 chrysler 300m?


remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley

Feb 09, 2010 | 1999 Chrysler 300M

3 Answers

My 1997 nissan pathfinder p0325 code came up on the scanner, and I need to change my knock censor on the car. I do not known were this part is located on the engine


very familiar with this. it is down under the intake manifolds in the valley of the engine. it is a single wire connector. you must remove the manifolds to replace this item. parts will run you about $100 and take about 3-6 hours depending on your compentance. parts needed are 1. knock sensor 2. intake(upper and lower plenum gasket)set 3. coolant. make sure you drain your radiator prior to doing this as to not allow a bunch of coolant to drain into the cylinders and cause hydrolocking. if this happens you must remove the spark plugs and rotate the engine to spray out the liquid out of the cylinders then reinstall.

Dec 24, 2009 | 1997 Nissan Pathfinder

1 Answer

99 Lumina Won't start after intke gskt chng--fuel system clicking


Sound like you forgot to put new O-rings on fuel injectors.you have a intake leak through the injectors ports. that why car wont crank .remove fuel rail.replace upper and lower O-rings on fuel injectors.

Jul 19, 2009 | 1999 Chevrolet Lumina

1 Answer

Knock / Cam Sensor


The Knock Sensor is Located under the Intake Manifold.. It can be seen vias a flash light from the Driverside Looking down into the open area below the intake manifold approx 8in. Inside. If you are going to Remove/Replace the Knock Sensor You will have to Remove the Intake Manifold. Whick is not as hard as it may look. You will also have to replace the Gasket on the intake it self.

Jun 21, 2009 | 1997 Nissan Maxima

4 Answers

Need to locate knock sensor on 1999 camry V6. Where is located.


i have toyota windom 4vz-fe i need locate knock sensor

May 31, 2009 | 1999 Toyota Camry

2 Answers

When replacing the camshaft sensor in a 1999 alero 3.4 v6...does the intake manifold have to be removed?


No i will post the procedure below.


3.4L REMOVAL OF CAM SENSOR

1. Turn OFF the ignition.

2. Remove the serpentine drive belt.

3. Disconnect the sensor electrical connector.

4. Remove the power steering pump, if required.

5. Remove the attaching bolt.

6. Remove the sensor.

7. Inspect the sensor for wear, cracks or leakage if the sensor is not being replaced.



To install:

1. Lubricate the O-ring with clean engine oil and replace if damaged.

2. Install the camshaft Position Sensor.

3. Tighten the retaining bolt to 8 ft. lbs. (10 Nm).

4. Connect the sensor electrical connector.

5. Install the power steering pump, if removed.

6. Reinstall the serpentine drive belt.


May 25, 2009 | Oldsmobile Alero Cars & Trucks

Not finding what you are looking for?
1999 Chevrolet Lumina Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...