Question about Cars & Trucks

1 Answer

I have dodge ram 1500 v8 model 2002 no start can you help me

I have dodge ram 1500 v8 engine model 2002 problem is the engine wont start i have a spark on the spark plug

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,370 Answers

If the spark is getting right.Get the fuel system checked.Its quite possible that fuel pressure is low or fuel pump not starting up right.

==========

CAR NO START PROBLEMS:-----


It can be the issue with weak battery or faulty battery or if battery is ok,then its faulty starter causing the issue.


From start to end troubleshooting these problem i suggest you to click the link below and follow its procedure:-----



What to Do When Car Turns Over But Won't Start?

http://technoanswers.blogspot.com/2012/11/what-to-do-when-car-turns-over-but-wont.html


-----------

Car starting issues?

http://technoanswers.blogspot.in/2012/02/car-starting-issues.html

------------

Car Starting Problems

http://whoisbyme.blogspot.in/2012/06/car-starting-problems.html


--------

1991 Toyota Trecel: Engine Starts fine but dies when gets Warm?

http://whatisbyme.blogspot.in/2012/05/1991-toyota-trecel-engine-starts-fine.html

----------

1994 Toyota Pickup: Starts fine but dies in few seconds?

http://howtobyme.blogspot.in/2012/05/1994-toyota-pickup-starts-fine-but-dies.html


---------

1999 Chrysler Cirrus: 8 IGN Fuel Starter Fuse Blows?

http://whatisbyme.blogspot.in/2012/06/1999-chrysler-cirrus-8-ign-fuel-starter.html


-----------

2001 Toyota Camry: No start After replacing Battery?

http://whatisbyme.blogspot.in/2012/05/2001-toyota-camry-no-start-after.html

----------

1989 Toyota Pickup Truck: Turns over but not start?

http://whatisbyme.blogspot.in/2012/05/1989-toyota-pickup-truck-turns-over-but.html

--------------

Car dead and will not Start?

http://whatisbyme.blogspot.in/2012/05/car-dead-and-will-not-start.html

--------

1995 Lexus LS400: Running Hot?

http://whatisbyme.blogspot.in/2012/05/1995-lexus-ls400-running-hot.html


----------

2001 Toyota Prius will not start?

http://whatisbyme.blogspot.in/2012/05/2001-toyota-prius-will-not-start.html

---------

1996 Jeep Grand Cherokee: Engine will not start?

http://repairhelpcenter.blogspot.in/2012/06/1996-jeep-grand-cherokee-engine-will.html

-------------

Mitsubishi will not start

http://www.howtorepairguide.com

---------

These will help.

Thanks.

Posted on Nov 28, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 512 Answers

SOURCE: 2001 dodge ram 1500 v8 spark plug wire diagram

the firing order is 1 8 4 3 6 5 7 2 clockwise around the cap

Posted on Jan 03, 2009

Molson02536
  • 3854 Answers

SOURCE: cant find spark plugs

To do the job to factory specs, you'll also need a torque wrench--a little 3/8" drive one that can handle 8-20 N-m and will fit in tight spaces is the way to go--some anti-seize compound for the spark plug threads, some silicone grease for the O-rings on the coils, and a source of compressed air. I really needed the compressed air. There was a bunch of dirt in the rear plug holes on both sides I wouldn't have wanted in my engine. 

To get access to everything, remove the 10 mm bolt on either side of the resonator, release the four spring clips on the air filter box, release the the air filter box cover from the hooks on the engine side, then lift the front of the resonator to remove the plastic pin from the rubber grommet at the front of the resonator and work the resonator out of the rubber gasket that connects it to the throttle body. There is no clamp holding the resonator to the throttle body gasket, it just has a friction fit. Set the whole resonator/hose/air filter box top assembly aside. Stuff a clean shop rag in the throttle body gasket to keep dust from blowing into the throttle body. Remove the air filter and put it in a clean spot for the same reason. You may want to remove the left hand Allen screw on the resonator bracket and loosen the right hand screw so you can swivel the resonator bracket up out of the way to access the #1 coil nut with a socket. 

Do one coil/plug at a time so there is no way you can drop a part in a cylinder! Unplug the connector to the coil by pushing down on the release on the top of the plug and sliding them out of the coil. 

After removing the 10 mm nut that holds each coil in place, use compressed air to blow out all the dust around the coil, then remove the coil (pull up gently with a little twisting motion back-and-forth) and blow all the dust around the spark plug out so you don't get anything nasty down in the cylinders. 

Your OEM plugs are NGK ZFR6F-11G, gapped at 0.042-0.044, Use the anti-seize compound on the spark plug threads so you can get them out next time. Finger-thread the plugs until they are snug, then torque them to 20 N-m.

A thin coat of the silicone grease goes on the O-ring on the coil to make it easier to install in the cylinder head and to make the O-ring last longer. Install the coil on the plug, then put the 10 mm nut back on to fasten the coil down. Torque the coil nut to 8 N-m. Re-connect the connector, and go on to the next plug.

If you have the right tools, this job is easier than doing it with an old distributor/plug wires setup, and the whole thing will cost you less than $20 including the plugs, the anti-seize and the silicone grease. 

Good luck and hope this helps

Posted on May 25, 2009

  • 312 Answers

SOURCE: need a spark plug diagram for 2001 dodge ram 1500

starting from the drivers side front, is #1,then next is #3 then #5 then #7 start from passenger sidefront is #2 then #4 then #6 then #8. the firing order is 18436572.

Posted on Feb 09, 2011

charleshucke
  • 1114 Answers

SOURCE: Helpppp - May I get the spark plug firing order

18436572 is the firing order, I will look for the diagram for ya.

Posted on Mar 03, 2011

ZJLimited
  • 17970 Answers

SOURCE: 2001 dodge ram 1500 5.2 v8 van spark plug diagram

2001 Dodge RAM 1500 ½-Ton 2WD Pickup 5.2 liter V-8 VIN "Y"

zjlimited_292.gif

Hope helps.

Posted on Apr 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the oil pump on a 2002 Dodge Ram 1500 4.7L V8 engine?


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
2002 Dodge Ram

Jul 31, 2016 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Can I put a 1998 dodge ram 1500 4.7L V8 engine in a 2002 dodge ram 1500?


Yes it will fit but why, it is a very poor engine choice as they are fraught with mechanical problems. the 5.2L is a better choice.

Jun 30, 2016 | 2002 Dodge Ram Pickup 1500

1 Answer

Can I use a 1995 dodge ram 1500 starter in a 2002 dodge ram 1500


I guess the short answer is no.
It depends on the engine and trans, but the starter for a 1995 model 5.2 is different from a 2002 model with a 4.7 engine.

Sep 16, 2015 | 1995 Dodge Ram

1 Answer

2002 dodge ram 4x4 1500


It could be low fuel pressure. Have it tested with a gauge.

Jun 26, 2013 | Cars & Trucks

1 Answer

What does the p1391 code on a 99 dodge ram 1500 5.2l v8 meen


check engine light and code P1391 crank or cam position sensor

The above can cause rough idle on the Dodge Ram 1500 5.2L V8 Engine.

Can try to replace the sensor, but verify that the wires are ok first.

Aug 12, 2010 | Dodge Pickup Cars & Trucks

1 Answer

I recently bought a 2002 5 speed 4.7l v8 dodge


The following are the common maintenance expenses after 200000 km.

1. Clutch Plate or even entire assembly recondition
2. Brake Assy maintenance
3. Check the engine performance, like speed, engine heating, etc ( Due to improper service or maintenance you may also face the problem )

Thank you.

May 08, 2010 | 2000 Dodge Ram 1500 Truck

2 Answers

Need firing order on a 1996 dodge ram v8


The order should be stamped on your intake manifold right under the air cleaner.
My '97 1500, 5.2, 318 firing order is 1-8-4-3-6-5-7-2

Hope this helps

Sep 17, 2008 | 1996 Dodge Ram 1500 Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

332 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...