Question about 1999 Volkswagen Passat
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 1999 volkswagen passat
Not sure where a cheap Rubber elbow is located on a passat. But do take off the coil covers. They are located under the engine cover. They are the 4 square caps. They come off with a allen wrench i believe 5mm. Then pull them off. Due this 1 at a time. Once off look down the hole with a flashlight.
And look at the rubber surrounding the coil. Their should be no moisture. If their is moisture try blowing it out with compressed air.
Posted on Nov 23, 2008
THis is common Too common. As I posted before.
As I posted in the Passat questions.
The jetta may slightly differ.
Yes. If your window has fallen down and will not roll up.
99% Chance you car is suffering the Infamous VW plastic clip.
The door panel comes off With a T-10 torx or a Hex (Allen) wrench
that will fit and A large Philips Screw Driver..
Remove the Plastic cover on the inside Door handle.
And the Screw or Screw along the Bottom of the door panel.
Then remove the screws that hold the handle the the door.
They are located behind the Plastic plate you removed with a tiny screw driver earlier... Be careful not the mark up the cover whaytprying it up. It is best to pry from underneath. Where marks if made can not be seen
After the screws are out 4 I believe. The Use of a CLip tool ir best.
For getting behind the panel to pop it off. A screw driver will work.
After all the clips are released. Pull the light at the bottom of the panel down and out. Disconnect it ur push it back thought the hole it came from..
Now you need a 10mm socket, or wrench to remove the 12 bolts that hold the metal plate to the Door. Remove all the 10mm bolts, If the widow has not already fallen in the door. It should be released. By removing the Black 2" plugs. THe loosen the bolts that clamp the window the the arms. DO NOT LOOSEN THEM ALL the way, .
Disconect the all the wiring.. THe Door lock cable,can be a pain.
I think it pulls down,.
Next remove the Metal plate. that is the regulator.
reverse to install
Posted on Jun 26, 2009
If you still have a belt on power steering pump then it may have ran dry. Check fluid in power steering pump. If no belt to pump then replace lost one.
Posted on Jul 01, 2009
you have to get special socket that made for o2 sensors you can get local part store and you have to know which sensor you have to replace.
Posted on Aug 28, 2009
Tips for a great answer:
Jan 19, 2013 | 1999 Volkswagen Passat
Aug 17, 2012 | 1999 Volkswagen Passat
Apr 28, 2011 | 1999 Volkswagen Passat
Jan 23, 2011 | 2001 Volkswagen Passat
Jan 15, 2011 | 2003 Volkswagen Jetta TDI
Aug 09, 2010 | 1999 Volkswagen Passat
Jul 10, 2010 | 1999 Volkswagen Passat
Jul 01, 2009 | 2003 Volkswagen Passat
Apr 26, 2009 | 1999 Volkswagen Passat
May 21, 2017 | 1999 Volkswagen Passat
169 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: