Question about Suzuki Vitara

Open Question

Twincam timing marks for suzuki m13a engine

Need to know timing mark locations for m13a twincam. some one replaced chain and let cams spin. does'nt appear to be aligned properally

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 2001 chrysler concord 2.7 liter timing set

I have a similar problem. I just replaced the water pump and now the POS wont start. Like it is not getting fuel>

Posted on Sep 27, 2008

Ad
psds4
  • 293 Answers

SOURCE: timing marks,cam and crank,2.4l

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528018d02c

Posted on Oct 09, 2008

  • 186 Answers

SOURCE: changed timing chain and need to align to cam with the crang

Align the chain with the colored links on the chain over the marks on the cams.Twin cams Have a small hole on the cam gears that will align with a hole in the front of head.Crank Gear has a pip mark that goes straight up.colored links on crank go to the 5 & 7 Oclock position on the lower crank gear with pip mark on crank gear at 12:00.Hope this helps

Posted on May 22, 2009

  • 20 Answers

SOURCE: 95 Eagle Summit 1.8L cam timing marks

get a repair manual there must be a mark or reference point of some kind

Posted on Jul 02, 2009

  • 102 Answers

SOURCE: valve timing check

Chain drive. Unless the engine's been apart, why would the cam/valve timing change?
Valve clearances are another matter, and unless you want to remove the camshafts, get a mechanic who has the proper Suzuki tool to do them for you. You can measure the clearances, but the shims are between the cam lobe and the valve bucket, and the special tool holds the bucket down whilst changing to a thicker or thinner shim.

Posted on Sep 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is top dead centre on a suski vitra 54 olate ?


which engine,?
what year, 2005
and what does 44 olate mean?
these cars have many engines, called engine options.
1.8L and 2.5L are common.
you never said what you are attempting to do?
1: replace timing chain?
2: check spark timing? (it's fixed in the ecu, but on engine early the cam sensor can be moved and set wrong.

all all these engine, the damper pulley (crank pulley) is marked with a notch and then a scale above.
others (newer) have only 1 mark set. for spec, timing.

on my 2.5L the CAM sensor can be set wrong.
and the spec, is stated on the EPA hood sticker.
and on mine , 04' the timing freeze jump is gone (DLC)
and was moved to SUZUKI scan tool only usage.

so :
what engine?
what country?
and what are you attempting???????????????

May 11, 2014 | 2005 Suzuki Vitara

1 Answer

Timing mark locations for 2003 3.0 suzuki xl7


3.0?????
cam>? what are you timing, we cant guess that, ?
2.7L V6?????? (or 2.5 in some countries)
the cam chains?
there are 46 steps and 12 marks,
ever seen alldata.com , read the engine mech, chain section
suzuki pit stop?
https://suzukipitstopplus.com/Products/10182-2007-xl7-service-manual.aspx


best source is.
http://www.scantool.net/software/alldata-diy-1-month-subscription.html



Apr 23, 2014 | 2003 Suzuki XL-7

1 Answer

Timing mark of suzuki engine m13a twincam fitted with timing chain


non stock? if not stock, say so , 1st thing.
post a question , you state only nouns.
all engines (gas) have 2 timings
1: spark
2: cam.
what is your question.?
my guess is you are not in uSA? state location.
used on swifts or jimny.
year?

chain marks. spark marks or crank pulley marks.
4th google hit. huge 1.3 PDF, id bet its there...
http://www.google.com/url?sa=t&rct=j&q=suzuki%20m13%20timing&source=web&cd=4&cad=rja&ved=0CDoQFjAD&url=http%3A%2F%2Fwww.vems.hu%2Ffiles%2FFero%2Fsuzuki%2520VVT%2F4.pdf&ei=pHIwUtf7AeHg2AWi_IHQBg&usg=AFQjCNGAIMvbaLlj5qu5g-_MnFOcSRDtaA


m13 is not easy find, information.... but google will find it if you just use it. I promise.
Alldata.com dont cover it.

Sep 05, 2013 | Suzuki Vitara Cars & Trucks

1 Answer

We are installing a timing chain in our 1995 Jeep cherokee sundown edition for the first time can you please send me the timing gear specs the motor is a 4.0 with air. thank you


By :"specs" I assume you need install position? To index the gears, whne you take it apart, turn the crank pulley 'till the timing mark aligns with the "0" on the timing scale. Don't turn the crankshaft again. When you are ready to install the chain, locate the mark on the crank gear and align the mark on the cam gear so they point to each other. The mark on the crank gear should be at 12 o'clock and the cam gear mark at 6 o'clock. Make sure when you put the cam gear on the cam that the location pin fits into the gear to position it correctly. Jeep recommends that after putting the chain and gears on, you rotate the engine by hand and place the crank mark at 6 o'clock and the cam gear at 3 o'clock, then count the number of pins in the chain (pins, not links) between those two points. There should be 15 pins. If you are rebuilding the engine and have the cylinder removed, it's a good time to check the front crank pulley (some have the outer ring move on the rubber). Put a piece of flat steel across #1 cylinder with a bolt through the steel extending into the bore center. Turn the engine by hand 'till the piston contacts the bolt. Make a mark on the pulley and turn the engine in the opposite direction till contact is again made. Your timing mark on the pulley should be exactly between the two marks you made. If not, make a new mark at that point and use that as your actual TDC reference. If it is radically off, replace the pulley.
When setting up cam position I always use a degree wheel. If you are installing an aftermarket cam
its important to do that. If you're just replacing a stock chain, You will be fine with the method I've outlined.

May 16, 2011 | 1995 Jeep Grand Cherokee

2 Answers

Hi! What are the correct timing marks for a 1.8 suzuki esteem engine. I needed for change the timing chain. Thanks


if you take off the upper belt cover and line up the top dead center timing mark the cam mark will be right on or off 180 degrees. Line up the dot on the cam with the arrow by rotating the crankshaft around till both the cam mark and the crank TDC mark line up. Now when you take off the lower cover all the marks will line up for the crank. They are usually pretty obvious, but if your are not sure at this point you can always paint your own. Just make sure when you slide the new belt on , all the timing marks line up.

Dec 28, 2010 | 2001 Suzuki Esteem

3 Answers

Could you let me know where the timing marks are for a Suzuki Grand Vitara 1.9 DDiS


check around the inside (towards the block) edge or crank shaft pulley by the lower passenger side of the engine. Otherwise it will be by that pulley on the bloc, those are the only laces I've known them to be. Hope it helps

Jun 07, 2010 | 2007 Suzuki Grand Vitara 4WD

1 Answer

I need a diagram of timing chain replacement Thank You


During most engine rebuilds, a completely new timing assembly should be installed. If wear exists on any component, replacement of the entire assembly is necessary. Wear in the chain, gears, or sprockets means a timing lag, which results in poor engine performance.
The timing chain or belt is generally installed with the gears in their correct positions. Before installing a new chain, soak it in oil.
OHC (Overhead Cam) Engines
Some OHC engines use a chain drive; others use a belt drive. Removing the cover on some OHC engines that have timing chains is more difficult, because the cover often fits between the oil pan and the cylinder head. There are special procedures for replacing cam timing components in these engines.
Before a chain repair job, perform a leakage test on non-freewheeling engines to check for bent valves, so that an accurate repair estimate can be made.
OHV (Overhead Valve) Pushrod Engines
On many OHV pushrod engines, the crankshaft sprocket is installed on the crankshaft nose and the crankshaft is rotated to position piston #1 at TDC. At this point, a mark stamped onto the crankshaft sprocket is pointing directly upward (toward the camshaft).
The camshaft sprocket is then temporarily bolted to the cam and used to rotate the cam until a mark stamped on the cam sprocket is pointing directly downward (toward the crankshaft). The sprocket is then removed from the cam (without allowing the cam to rotate).
The timing chain is looped over the cam gear, the mark on the cam gear is positioned directly downward, and the chain is looped around the crankshaft sprocket. When the cam sprocket is attached to the cam, the timing marks on the crank and cam sprockets should be pointing toward one another. NOTE THIS IS FOR 2WD 4.0

May 22, 2010 | 2005 Nissan Pathfinder

1 Answer

TIME CHAIN


Did you put the chain back on exactly like it was? I haven't seen a timing chain in years, anyway, if you didn't get that thing right, the car won't go 10 miles without causing major damage. Did you mark it some how to the cam marks and the crank marks? If you still have it open, check it out to be sure, line up the marks to the marks on the chain, if it has them, if not, You will have to put the engine at tdc, then roll the cams to their marks, get the chain on there, spin the engine by hand a couple dozen times, pull some spark plugs out to relive the compression. Hope this helps.

Apr 08, 2010 | 1995 Nissan Maxima

2 Answers

Timing marks


Autozone.com has free repair info. They gave a great decription of the 3 timing chains and marks for my 2001 V6 2.5L engine. The motor ran perfect with their help.

May 27, 2009 | 2001 Suzuki Grand Vitara

1 Answer

Valve timing check


Chain drive. Unless the engine's been apart, why would the cam/valve timing change?
Valve clearances are another matter, and unless you want to remove the camshafts, get a mechanic who has the proper Suzuki tool to do them for you. You can measure the clearances, but the shims are between the cam lobe and the valve bucket, and the special tool holds the bucket down whilst changing to a thicker or thinner shim.

Apr 15, 2009 | Suzuki Aerio Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

405 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...