Question about 2005 Subaru Forester

Open Question

Where is the coolant temperature sensor on my 2000 ford e250 van

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 119 Answers

SOURCE: replacement of coolant temperature sensor

located under intake in water crossover pipe,you can access the sensor by removing intake chamber box,then pcv hose connected to the block,the connector is orangeish 2pin,use a 19mmdeep socket on a 3/8 ratchet to get it loose,make sure engine is cool,also make sure there is a new brass washer with your new sensor,sometimes the old washer comes off when removing the sensor,sometimes it sticks to the pipe,some coolant will escape so make sure to top it off

Posted on Jul 14, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the IAT sensor located in a Ford E250 1993


IT SHOULD BE LOCATED IN THE INTAKE MANIFOLD ON THE LEFT SIDE FRONT, NOT IN THE COOLANT PASSAGE, 2 WIRE SENSOR, ROUND CONNECTOR

Jul 21, 2013 | Cars & Trucks

1 Answer

Heater on 96 windstar van blows cold air


first make sure your coolant is full. if it is then you could have temperature switch or sensor bad,not the temperature sensor for the motor though(not the one for your temperature gauge in other words).

Dec 10, 2012 | 1996 Ford Windstar

1 Answer

Location of engine coolant temperature sensor


Automobiles: 2000 Ford Escort ZX2 4-cylinder 2.0L MFI DOHC

NOTE
The "left" side of the engine is the driver's side.

The Engine Coolant Temperature (ECT) sensor is a thermistor (a device which changes resistance or voltage as temperature changes). The sensor detects the temperature of engine coolant and provides a corresponding signal to the PCM (Powertrain Control Module - aka "the car's computer").

The ECT sensor is mounted in the following locations (small Ford engines):

1.8L engines: in the cylinder head
1.9L engines: threaded into the heater hose inlet pipe
2.0L engines: at the left rear of the engine

2.0L Zetec Engine

(1) Partially drain the engine cooling system using a clean container. If coolant is in good condition, retain for reuse.
(2) Disconnect the battery ground cable.
(3) Disconnect the electrical wiring connector from the engine coolant temperature (ECT) sensor.
(4) Remove the retaining clip and the ECT sensor.


12_5_2011_5_38_05_pm.jpg

Fig. 1 Escort ZX2 ECT sensor - The retaining clip is removed (at the solid arrow). Withdraw ECT sensor by gently wiggling/pulling in the direction of the dashed arrow.

To install:

NOTE
Coat the ECT sensor O-ring with clean coolant prior to installation.

(1) Replace the retaining clip and the ECT sensor.
(2) Connect the electrical wiring connector from the Engine Coolant Temperature (ECT) sensor.
(3) Connect the battery ground cable.
(4) Refill the engine cooling system. An inexpensive plastic "Radiator Funnel" will help with this task.

Dec 05, 2011 | 2000 Ford Escort

1 Answer

Ford e250 gas van 5.4 engine 2000 model oil in water


Head gasket could be leaking from oil passageway to coolant passage without significant amount of coolant going to oil. A new head gasket may have to be installed to repair this problem.

Nov 04, 2011 | Cars & Trucks

1 Answer

I have a 2002 e-250 van and when im at a stop light it revs up and down eraticaly. A friend told me its the I.A.C.V and that I could clean it so I did and nothing happened ..The van also has just started...


possible fuel pump. test the fuel pressure. possible M.A.F.. test first. then attempt cleaning with approved maf cleaner. check coolant level, test coolant temp sensor.

Feb 01, 2011 | 2002 Ford E250

1 Answer

Where does the cooler sensor go on a 2002 e250 ford van


The ECT, engine coolant temp sensor? On the engine with 2 pin connector

Oct 28, 2010 | 2002 Ford E-Series

2 Answers

Where is the temperature sensor for a ford e-150 van 1994 on a 300ci v-8 engine. Thanks rick


1994 Ford Truck E150 1/2 ton Van 5.8L MFI 8cyl Temperature Switch is located: Front seating area, center, under engine cover, front driver side of intake manifold, mounted in engine block.

The ECT sensor (Engine Coolant Temperature Sensor) is located either in the heater supply tube at the rear of the engine, or in the lower intake manifold. The ECT sensor is a thermistor (changes resistance as temperature changes). The sensor detects the temperature of engine coolant and provides a corresponding signal to the PCM. From this signal, the PCM will modify the air/fuel ratio (mixture), idle speed, spark advance, EGR and canister purge control. When the engine coolant is cold, the ECT sensor signal causes the PCM to provide enrichment to the air/fuel ratio for good cold drive-away; as engine coolant warms up, the voltage will drop.

c1fb19f.gif

Engine component locations-1994 5.8L engines

I hope help you with this, good luck (remember rated this help).

Sep 02, 2009 | 2002 Ford E-Series

1 Answer

1999 Ford E250 Van will not start


i've never heard of a cold temp sensor... theres an intake air temp sensor it goes in the large plastic tube that comes off your air filter box, i doubt this is your problem tho.. i would lean more toward the fuel pressure regulator or one of the injectors could be dumping. also a clogged catylitic converter may cause an overfueling situation. hope this helps and good luck

Jun 24, 2009 | 1999 Ford Econoline

1 Answer

Where is the engine coolant sensor located on a 2000 ford f150 V8 4.6 L?


please rate as fixya if this helps

SECTION 303-14: Electronic Engine Controls 2000 F-150 Workshop Manual
REMOVAL AND INSTALLATION Engine Coolant Temperature (ECT) Sensor — 4.6L and 5.4L Removal and Installation
  1. Remove the engine coolant temperature (ECT) sensor.
    1. Disconnect the electrical connector.
    1. Remove the ECT sensor.
ae8a8e7.gif The ECT sensor:
  • sends the PCM a signal indicating engine temperature.
  • resistance decreases as coolant temperature increases.
The ECT measures the temperature of the engine coolant. The sensor is threaded into an engine coolant passage.

Mar 19, 2009 | 2000 Ford F150 Flareside SuperCab

Not finding what you are looking for?
2005 Subaru Forester Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...