Question about 2004 Hyundai Elantra
How much will it cost to replace?
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Open the ashtray, and grab the bottom of the bezel. Its only clipped in, so give it a yank and the bezel will come off. Unplug the connectors and replace your switch.
Posted on Jul 02, 2008
yes , you need to remove the headlight cover from the back after u move the bulb conector then there is a holder for the bulb u need to push down then move.
i hope it help ,,,, thanx
Posted on Mar 16, 2009
Just the belt if that is all you need. I would replace all the other belts as well. The Water pump pully has to come offYou can visual the pump better at that time. The easiest way to get the pully back on and off is to remove the Power steering resevoir and transaxell mount in fron middle. Jack the engine up as high as you can get it. Put a block under the pan when jacking to spread the push force. this will tilt it back and up so the pulley will stay ion the water pump nub. It is a two piece pully.
Posted on Jul 07, 2009
trying to do the same on my 01. ready to change the bulb but can't find it anywhere.
anyhow, here's how you do it:
remove the dash by taking out 2 screws behind the ashtray and 2 above the instrument cluster
begin prying off the dash from the ashtray up, when you reach the heater vents stop. next take a flat head screwdriver and pry off the dash from the left side with the door open. work left to right till you reach the heater vents and it'll come right off. you don't necessarily have to unplug any of the electric connectors if you don't want to, but you;ll have to reach around the dash while working. all you need to do now is remove the heater control unit via the 4 screws around it, then unplug the electric harnesses from the back of it. make sure you remember which goes where. the bulbs are the 3 white (or is it 2 white and 1 grey) circles on the back of the control unit. just turn them with a flathead screwdriver and turn it over and give it a little bump to get 'em to fall out (or grab 'em with a needle nose pliers if necessary). anyhow, that's how it's done, question is, where do ya find the bulbs?
Posted on Jul 10, 2009
First, disconnect the battery. Then the only part that needs to be removed to access the starter is the rubber air plenum boot between the throttle body and the air filter housing. This allows enough room to get an arm in there to access the 14mm bolts that attach the starter to the transmission. After removing the bolts, the starter can be removed from underneath the car. lower it down as much as possible, and unbolt the power cable. You may have to twist and turn it a bit to get around the support between the engine block and intake manifold, but it will come out.
Posted on Feb 07, 2010
Tips for a great answer:
Jan 16, 2015 | 2000 Hyundai Elantra
Apr 17, 2013 | 2006 Hyundai Elantra
Jul 03, 2012 | Cars & Trucks
Dec 15, 2010 | 2004 Hyundai Elantra
Nov 22, 2010 | 2004 Hyundai Elantra
Nov 03, 2010 | 2001 Hyundai Elantra
Dec 31, 2009 | 2004 Hyundai Elantra
Oct 01, 2009 | 2004 Hyundai Elantra
Dec 27, 2015 | 2004 Hyundai Elantra
120 people viewed this question
Usually answered in minutes!