Question about Mercedes-Benz CLK-Class

Open Question

Clk 320 want shift out of park used pen to unlock drive ok but when placing back in park locks again how can i repair?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 15 Answers

SOURCE: 2001 mb clk 320, my ignition switch will not turn.

Hi there
I had something similar on my merc
but yours sounds similar.
the fact that you say the steering lock no longer works is very worrying, most times the key not going past position 1 is due to the steering lock being actuated and the pressure in it has to be released before the key will turn, you will have to go from lock to lock the find where the steering lock actuates when this happens follow my wiggle method of turning the steering wheel slightly when the steering lock is on the disengage it. ie keep trying the key whilst wiggeling the steering wheel.
hope that helps

Posted on May 01, 2009

Ad
  • 218 Answers

SOURCE: My 2003 Mercury Mountaineer Gear Shift is stuck.

THERE IS A SENSOR ON THE BRAKE PEDAL THAT RELEASES THE THE SHIFTER.THERE A 3 COMPONENTS INVOLVED.U CAN PUT IT IN NEUTRAL BEFORE U START THE CAR.THEN WIL SHIFT.

Posted on May 01, 2009

  • 6 Answers

SOURCE: my mercedes clk 320 99 wont start , i turn the

This is probably your starter.

Posted on Jul 11, 2009

Wolfman304
  • 720 Answers

SOURCE: where is the trnsmission cap for clk 320 model

Hi there,

Mercedes have purposely not put a transmission dipstick in their cars...to STOP any unauthorised persons from tampering with transmission fluid levels.

Electronic transmissions are extremely temperamental - if incorrect type, level is too low (or too high), this will accelerate premature wear and tear, not to mention erratic shifting behaviour.

For this reason, only Mercedes service agents have the required workshop tool (ie dipstick) which they insert into a tube in the transmission, to check levels.

If you happen to obtain the correct tool for your own use....please ensure you use only Mercedes specified fluids....and NEVER overfill the transmission case.

Cheers,

Posted on Aug 16, 2009

Testimonial: "very very help full"

  • 1 Answer

SOURCE: my clk 320 mercedes wont shift into gear? what is

just had the same problem today...there is a small square false door just below the D on the shift plate...the tow guy put a pen into that door and i was able to shift it out of park. now the car won't shift gears as i drive because the car is in 'safe mode'. disconnect the battery to correct. the shifting issue is still unsolved but it appears to be an electrical issue in the transmission but NOT the actual transmission. hope this helps

Posted on Apr 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steering wheel is not locked and battery is dead and I can't shift it into gear


For the brake light, check the fluid level in the brake reservoir. For the engine light, scan the computer with an obd scanner and post the trouble codes here.

Jul 22, 2017 | Mercedes-Benz Cars & Trucks

1 Answer

The gear shifter on my 1998 Pontiac SE coupe will not unlock so I can take the car out of park


Do you have column or floor shifter ?
All automatic transaxle models use an electric park lock system. Within the housing assembly, a lock cylinder is connected to an actuator which rotates and engages on the electric park lock solenoid. When the floor-shift lever is not in the park position, the actuator disengages from the electric park lock solenoid slider. This allows the lock cylinder to move to the lock position. With the shift lever in PARK and the lock cylinder in LOCK, the actuator cam is positioned against the electric park lock solenoid slider. This prevents the shift lever from shifting out of the PARK position.
The column-shift automatic transaxle model uses a flexible cable actuator instead of an electric park lock system. One end of the cable is attached to the gate assembly. The other end of the cable is attached to the column mounted housing assembly. This system functions similarly to the floor-shift ignition lock system.
The manual transaxle model uses a push button lock cylinder. A clutch start switch is used. The clutch pedal must be pressed before the engine will crank. Refer to Park Lock System Check .
CAN you turn the key on ?
The gear selector does not shift out of PARK with the brake pedal depressed and the ignition switch in RUN.
Automatic Transmission Shift Lock Control Always On with Ignition in Run
Action
Value(s)
Yes
No

1

Was the BTSI System Check performed?
--
Go to Step 2
Go to Automatic Transmission Shift Lock Control System Check

2

Is this a column shift vehicle?
--
Go to Step 3 yes
Go to Step 4 no

3

  1. Move the gear selector to the PARK position.
  2. Disconnect the automatic transaxle control connector
  3. Turn the ignition switch to RUN.
  4. Connect the test lamp between terminal B and ground.
Does the test lamp light?
--
Go to Step 4
Go to Step 8

4

  1. Disconnect the brake switch connector C2.
  2. Move the ignition switch to RUN.
Can you shift the transaxle out of the PARK position?
--
Go to Step 5
Go to Step 8

5

Is the brake switch adjusted properly?
--
Go to Step 6
Go to Step 7

6

Replace the brake switch.
Is the repair complete?
--
System OK
--

7

Adjust the brake switch.
Is the repair complete?
--
System OK
--

8

  1. Disconnect the BTSI solenoid connector (column shift vehicles) or disconnect the automatic transaxle control connector (console shift vehicles).
  2. Move the ignition switch to RUN.
Can you shift the transaxle out of the PARK position?
--
Go to Step 9
Go to Step 10

9

Repair the short to power in CKT 1135.
Is the repair complete?
--
System OK
--

10

Test for sticking or binding in the shift linkage.
Does the shift linkage stick or bind?
--
Go to Step 11
Go to Step 12

11

Repair the shift linkage.
Is the repair complete?
--
System OK
--

12

Replace the BTSI solenoid (column shift vehicles) or replace the automatic transaxle control (console shift vehicles).
Is the repair complete?
--
System OK
Go to Step 1

May 18, 2015 | Pontiac Cars & Trucks

2 Answers

My smart key will not turn in my ignition on my clk320 year 2000 battrey was flat but it as been charge up and tested


sounds like a bad key and needs to be replaced. you cannot take it out of park unitl the key is rotated.

Feb 28, 2015 | 2000 Mercedes-Benz CLK

2 Answers

Cannot shift from drive to park but can shift using shift lock release


check your brake light switch for proper adjustment as wel as the electrical connection at the switch also check your fuses and make sure your brake lights are working

Aug 29, 2012 | 2006 Hyundai Sonata

1 Answer

320 clk mercedes fuse blows for central locking as soon fitted


There a shot this can be rub through wire or its power touching ground, The power goes into the door control module form there it reaches the door lock actuator, disconnect door lock actuator,if the short stop repair the actuator,if it does nt move to the driver door lock module disconnect that if the short stop its in the module if it doesnt its in the wire

Mar 13, 2012 | 2005 Mercedes-Benz CLK 320

2 Answers

My clk 320 mercedes wont shift into gear? what is wrong?


just had the same problem today...there is a small square false door just below the D on the shift plate...the tow guy put a pen into that door and i was able to shift it out of park. now the car won't shift gears as i drive because the car is in 'safe mode'. disconnect the battery to correct. the shifting issue is still unsolved but it appears to be an electrical issue in the transmission but NOT the actual transmission. hope this helps

Feb 10, 2010 | 2001 Mercedes-Benz CLK-Class

1 Answer

Hi i haven't drive my mercedez clk 320 2005 for about one yrs and the battery is dead, should i buy a new one or should i charge up to see if it work?


You could do either, if you will be driving it again now you may opt for a new battery. Take it out and have the battery tested at your auto parts store if it checks out OK charge it up

Jul 11, 2009 | 2005 Mercedes-Benz CLK

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...