Question about Chevrolet HHR

Open Question

How do you change the rear turn signal bulb in a 2009 HHR

I need to know if the bulb holder screws out or if there is something that needs pushed in for it to release

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: change rear signal bulb on 2002 ford focus wagon

Open the rear tailgate There are 2 screws that hold light housing in place.. Remove the screws then pull the housing outwards till the clip behind it springs. You then need to knock the housing sideways (outwards) to free the 2 prongs that attach housing to the car body.
Unclip the rear housing from the back of the light unit & change the bulb.

Posted on Jan 17, 2009

Ad
countrysi248
  • 443 Answers

SOURCE: Rear blinker does not work need to access bulb

Your rear bulb is burnt out if you say the front one is working .. the speed up of flashing means your bulb is bad.. you might have to get in the trunk and unscrrew those hand wing nuts and push that tail light outward to get to the bulbs ... thanks Jerry and holler if you need more.

Posted on Apr 22, 2009

  • 120 Answers

SOURCE: 2007 ford 500 rear turn signal bulb replacement

This is straight from the owner's manual.

#1 Make sure the headlamp switch is in the OFF position and open the trunk.
#2 Carefully pull the carpet away to expose the backside of the tail lamp assembly.
#3 Remove the nut and washer assemblies, then pull the lamp assembly away from the vehicle.
#4 Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly.
#5 Pull the bulb straight from the socket.

Install new bulb(s) in reverse order.
Good luck

Posted on Jan 23, 2010

  • 61 Answers

SOURCE: how do you replace a rear turn signal bulb on chev...

There is an access panel on the inside rear sides by the lift gate. They pop out giving you access to the bulbs. I recommend replacing both at the same time since they seem to "blow" within a few days of each other.

Posted on Jun 07, 2010

  • 61 Answers

SOURCE: How to change a front turn signal bulb in a 2006

The procedure for changing the front bulbs is described in the owners manual but it is not easy. It is the same for the headlights, turn signals, and fog lights. First, turn the wheels in (to the left for the right side) and then turn off the vehicle. You will then loosen the screws on the inside plastic wheel well until you can bend it out of the way. You can then reach inside, and the bulbs all come out with a 1/4 twist to the left. Make sure you remove the old gasket ring, and install the new bulb with only one gasket. Screw the wheel well back into position and you are done.

Posted on Jun 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hhr headlight replaced but still not working


I'm pretty sure there is a separate fuse for the left and right headlights. Did you check those?

Apr 18, 2014 | 2009 Chevrolet HHR

1 Answer

Changing the rear turn signal bulb


Some bulbs are really tough to remove on this car. Specially the front side lights. You have to first remove the panel in front of the tires. Hope this helps.

Apr 04, 2014 | 2007 Chevrolet HHR Fall

1 Answer

How to replace bulb in front bumper turn signal housing 1995 jag xj6


hello,
  • Identify the blown bulb. Note that if a headlight bulb has blown, the dip beam is on the outside and the high beam is on the inside. Turn off the ignition switch and light switches.

  • Open the hood and replace any blown headlight bulbs. Press the plastic spring clips and remove the bulb holder from the assembly. Pull the bulb out of the bulb holder and replace it with a new bulb. It only fits one way. Be sure not to touch the bulb's glass. Replace any parking lights at the same time, they are in the headlamp unit too.

  • Remove the front turn signal light unit in the bumper to change the turn signal bulb. Push gently on the inside edge and insert a blade between the bumper and the lens at the outside edge. Compress the spring and remove the lens. Fit a new lamp by inserting it into the plug. The side marker light is changed using a similar process.

  • Open the trunk to replace the rear fog light, stop light, tail light, reversing light and turn signal light. Remove the rear light cover and turn the bulb holder fastener 90 degrees counter clockwise. Remove the expired bulb, fit a new one and replace the parts, turning the bulb holder clockwise.

  • Thanks..

    May 21, 2011 | 1995 Jaguar XJ6

    2 Answers

    I can not figure out how to get into the rear light bulbs (Stop light, etc). The manual says to remove two (phillips) screws to disengage the housing from the body. There's even a a picture. However, on...


    To access the rear lights, you access them from inside the trunk. Pull down the carpet at rear of trunk near latch. There should be the screws the manual is referring to. Once you locate and remove all screws, gently pull the light assembly away from body. Replace the needed bulbs then gently push assembly against the body, replace the screws and set carpet back in place.

    Nov 14, 2010 | 1995 Toyota Camry

    1 Answer

    Rear turn signal how to change bulb


    open the liftgate remove the screws holding the tail,stop,turn signal and back-up light assembly to the rear door opening. seperate the light assembly from the vehicle body. disengaging the hook holding the outer end of the light assembly to the body. swing the housing out to access the bulb holders. rotate bulb holder and remove blown out bulb. installation is the reverse of removal. hope this will help!!!

    Apr 03, 2010 | 2005 Dodge Grand Caravan

    1 Answer

    07 chevy hhr i need to change my little turn signal light that is right next to my fog light how do i get to it


    This is a tough one, but the turn signal bulb (and also the headlight bulb) is accessed by opening up the inside wheel well.

    You will need to turn the steering wheel hard in, then turn the car off. There are both screws and push fasteners holding the plastic inside well in place. Loosen as many as needed to bend it out of the way and you can then reach inside and replace the bulbs.

    As a recommendation, you might as well replace both sides at the same time. They will both fail at about the same time.

    The owners manual actually describes this process, as also gives the information on the replacement bulbs.

    Feb 20, 2010 | 2008 Chevrolet Hhr

    1 Answer

    How to change a front turn signal bulb in a 2006 HHR


    The procedure for changing the front bulbs is described in the owners manual but it is not easy. It is the same for the headlights, turn signals, and fog lights. First, turn the wheels in (to the left for the right side) and then turn off the vehicle. You will then loosen the screws on the inside plastic wheel well until you can bend it out of the way. You can then reach inside, and the bulbs all come out with a 1/4 twist to the left. Make sure you remove the old gasket ring, and install the new bulb with only one gasket. Screw the wheel well back into position and you are done.

    Nov 29, 2009 | 2006 Chevrolet HHR

    2 Answers

    Audi A4 need to replace rear brake light on audi a4


    Inside the boot is a plastic cap embeded in the boot liner. Remove the cap to reveal a screw. Undo the screw and the whole rear light cluster will come away in a sideways and not rearward direction to reveal all of the bulbs. Hope this helps.

    Jun 04, 2009 | 2003 Audi A4 Cabriolet

    1 Answer

    How do I change rear Bulbs...does the one piece pop off how do i get into it to change bulbs..


    No you unscrew the four screws on the outside and then remove the lamp assembly then twist the bulb holder counter clockwise to remove the bulb holder from the car, next twist and remove bulb in same direction counter clockwise.

    May 17, 2009 | 1995 Nissan Pickup

    1 Answer

    How to change bulbs on front and rear turn signals


    open the hatch there should be two screws that hold on the lense, twist the bulb holders and remove

    Aug 08, 2008 | 2001 Jeep Cherokee

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    172 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8499 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...