Question about 2001 Ford Focus

1 Answer

Hood won't close on 1990 Toyota Camry

Not latching.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

The latch spring is out of alignment,needs lubrication, or has broken.
Spray with penetrating fluid and try again in 5-10 min.

Posted on Jan 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hood latch won't latch when closing


Raise hood,have some one go pull hood latch and you look at latch and see if it releases,if it doesn't then cable may need replacing,I would'nt completely shut hood cause you may not get back open,also check hood latches bolts and latch for something bent or broken.

Sep 21, 2012 | Chevrolet Silverado 1500 Cars & Trucks

2 Answers

95 dodge caravan drivers door won't latch


often normal door latches will wear out causing the door latch to not activate the "full latch". The full latch ends up moving further up and into the latch. the solution is to replace the latch or have it rebuilt.

Aug 03, 2012 | 1995 Dodge Grand Caravan

1 Answer

I need information on how to replace (or service) the door latch mechanism on my merc. I have realigned the door (and realigned the striker rod) and it will still not close. The latching system does not...


Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942) and watershield from front door (20124).
  1. Mark the location of the bolt retaining front door glass run front retainer (21572). Remove the bolt.
  1. Check all rod connections against the appropriate illustration. Correct any disconnected or loose connections and check operation before replacing parts.
  1. Remove power door lock actuator (218A42).
  1. Disconnect the rods from the front door latch (21812). The front door latch remote control link (21940) and the latch-to-lock cylinder rod cannot be removed at this time because of the rod's end configuration. Remove wiring from clip on front door latch shield.
  1. Remove front door latch control cylinder rod (22134) from the door lock cylinder (21985).
  1. Remove front door latch remote control and link (21818).
  1. Remove the front door latch retaining screws. Disconnect the door open warning lamp switch (14018) if so equipped. Remove the front door latch from the front door.
  1. NOTE: Do not damage anti-theft shield.
    Remove anti-theft shield from the front door latch.
  1. Remove front door latch remote control link, front door latch control cylinder rods and door open warning lamp switches from front door latch where applicable.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten front door latch retaining screws 4-8 Nm (36-70 lb-in).


    ganyapr_5.gif


Item Description 1 Front Door Latch Control Cylinder Rod 2 Front Door Latch Remote Control Link 3 Bushing 4 Door Latch Shield 5 Power Door Lock Actuator 6 Front Door Latch Control Cylinder Rod 7 Front Door Latch 8 Latch (1 Req'd) 9 Screws (2 Req'd)

Feb 13, 2011 | 1997 Mercury Cougar XR7

1 Answer

The tailgate latch, doesn,t latch


you have to make sure the strikers are lined up to the latch. The latches get dirt in them and dont move easily. You may have to remove the latches and clean them and grease them up make sure the action is working. There is a spring on the latch if it is broken you will have to replace the latch. Make sure as you before you shut the tailgate the the latches on the tailgate are open and not latched closed. You can put a screw driver in the latch and pull the handle and that should release the latch in the position ready to accept the striker when you close it Next make sure the plastic clip retainers are not broken on the handle

Dec 11, 2010 | GMC Sierra 1500 Cars & Trucks

1 Answer

My 2005 chevy Avalanche tailget will not latch.how do you fix it?


I assume the tailgate is in alignment and hasn't been in an accident. If that is good, then probably the latch mechanism or the latches themselves are plugged up with dirt or rust. Liberally spray WD 40 on both latches and inside latch mechanism. Work the latch to see if that frees it. If not, then you likely have something broken in the latch mechanism or the springs in the latches.

Jul 10, 2010 | 2004 Chevrolet Avalanche

1 Answer

Relpace trunck latch 1999 ols alero


TO REMOVE TRUNK LATCH YOU HAVE TO DISCONNECT TRUNK LATCH CABLE FROM LOCK CYLINDER END.THEN YOU MARK TRUNK LATCH RELATIONSHIP TO THE TRUNK LID AND DISCONNECT THE ELECTRICAL CONNECTOR AT THE TRUNK LATCH.REMOVE THE LATCH RETAINING BOLTS AND REMOVE THE LATCH.PUT EVERY THING BACK VISA VERSA.

Jul 06, 2010 | 1999 Oldsmobile Alero

3 Answers

I have a 2006 Saturn Vue. The front passenger


there is a spring inside the door lock that makes it work this spring is most likely broken try spraying lubricant on the lock just in case its binding ,but it seems like you will have to replace the lock mechanism

Feb 07, 2010 | 2006 Saturn Vue

1 Answer

I had to pull open my door on my 08 Pontiac G6 and it is not latching when I shut it now. The actual mechanism is moving just not catching the latch.


Look at the door latch if the latch is in the lock position the stricker will not go into the latch to close the door, the latch should have a clear path all the way into the latch, if it don't get a screw driver put it in the latch hold the handle as to open the door and slide the hook in the latch out, that should reset the latch.Good luck.

Dec 24, 2009 | 2008 Pontiac G6 Sedan

1 Answer

Trying to remove door latch on 1995 thunderbird. Car has power locks.


inside or outside latch? please rate

Section 01-14A: Handles, Locks, Latches and Mechanisms 1995 Thunderbird, Cougar Workshop Manual
REMOVAL AND INSTALLATION Latch, Door Removal and Installation
  1. Remove front door trim panel (23942) and watershield from front door (20124). Refer to Section 01-05 .
  1. Mark the location of the bolt retaining front door glass run front retainer (21572). Remove the bolt.
  1. Check all rod connections against the appropriate illustration. Correct any disconnected or loose connections and check operation before replacing parts.
  1. Remove power door lock actuator (218A42).
  1. Disconnect the rods from the front door latch (21812) . The front door latch remote control link (21940) and the latch-to-lock cylinder rod cannot be removed because of the rod's end configuration. Remove wiring from clip on front door latch shield.
  1. Remove front door latch control cylinder rod (22134) from the door lock cylinder (21985).
  1. Remove front door latch remote control and link (21818).
  1. Remove the front door latch retaining screws. Disconnect the door open warning lamp switch (14018) , if so equipped. Remove the front door latch from the front door .
  1. NOTE: Do not damage anti-theft shield.
    Remove anti-theft shield from the front door latch .
  1. Remove front door latch remote control link , front door latch control cylinder rods , and door open warning lamp switches from front door latch , where applicable.
  1. To install, reverse Removal procedure. Tighten front door latch retaining screws 4-8 Nm (36-70 lb-in).
3e933ef.gif

Item Part Number Description 1 21852 Front Door Latch Push Button Rod 2 21940 Front Door Latch Remote Control Link 3 386656-S Bushing 4 21978 Door Latch Shield 5 218A42 Power Door Lock Actuator 6 22134 Front Door Latch Control Cylinder Rod 7 21812 Front Door Latch
------------------------------------------------------------------------------------
Remote Control Assembly Door Latch
Removal and Installation
  1. Remove front door trim panel (23942) and watershield. Refer to Section 01-05 .
  1. Remove screw and washer assembly retaining front door latch remote control and link (21818) to front door (20124) .
  1. Rotate front door latch remote control and link to remove from front door latch remote control link (21940) .
  1. To install, reverse Removal procedure.

Sep 27, 2009 | 1995 Ford Thunderbird

1 Answer

2001 Ford Escape Rear Hatch won't unlock


The liftgate consists of the following components:
  • liftgate door lock actuator
  • liftgate lock cylinder (if equipped)
  • liftgate window glass
  • liftgate window latch/ajar switch
  • liftgate window glass release handle
  • liftgate latch remote control which consists of the following component:
    • liftgate release handle
  • liftgate latch, which consist of the following component:
    • liftgate latch door ajar switch
Liftgate Latch Actuator Removal and Installation
  1. Remove the liftgate latch remote control. For additional information, refer to Liftgate Latch Remote Control in this section.
SECTION 501-14: Handles, Locks, Latches and Entry Systems 2001 Escape Workshop Manual
REMOVAL AND INSTALLATION Liftgate Latch Removal and Installation
  1. Remove the liftgate trim panel.
  1. Disconnect the liftgate ajar switch electrical connector.
  1. Disconnect the liftgate latch actuating rod.
    1. Open the clip.
    1. Disconnect the actuating rod.
  1. Remove and discard the liftgate latch bolts.
  1. Remove the liftgate latch.
  1. NOTE: Make sure the liftgate latch release rod is not preloading the latch. It should be clipped in a relaxed state with no slack.
    NOTE: Position the liftgate latch release rod by pushing outboard to remove the slack.
  1. Remove the screws and the liftgate latch actuator
90f640f.gif

May 29, 2009 | 2001 Ford Escape

Not finding what you are looking for?
2001 Ford Focus Logo

Related Topics:

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74418 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

fordexpert

Level 3 Expert

5433 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...