Question about Cars & Trucks

Open Question

Astrostart 2504a trouble code 19, how to fix this

Parking lights flash once, but does not start. the trouble shooting code reads "module does not detect manual interface", how do i solve this problem and get my remote starter working again - astrostart 2504a

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fastboyz
  • 674 Answers

SOURCE: I have a 1989 s-10.The

RWAL Fault codes
Codes for Dodge RWAL, Ford RABS and GM RWAL applications are similar but have a few differences:

  1. Should not occur (replace the controller if it does)
  2. Open isolation valve circuit or defective ABS module
  3. Open dump valve circuit or defective ABS module
  4. Grounded or closed RABS or RWAL valve switch
  5. Excessive actuations of dump valve during ABS braking
  6. Erratic speed sensor signal
  7. Shorted isolation valve or defective ABS module
  8. Shorter dump valve or defective ABS module
  9. High resistance or open speed sensor circuit (resistance should be 1000 to 2500 ohms)
  10. Low speed sensor resistance (Dodge & Ford only)
  11. Open speed sensor circuit (GM only)
  12. Stop lamp switch circuit (Dodge & Ford)
  13. ABS module speed processor (Dodge & Ford only)
  14. ABS module program (Dodge & Ford only)
  15. ABS module RAM memory failure (Dodge & Ford)
To manually clear a stored fault code on GM and some Dodge trucks with RWAL, remove the ABS fuse or disconnect the battery for 5 seconds. Ford RABS codes will automatically clear when the ignition is turned to the off position.

Posted on Aug 26, 2008

Ad
  • 1 Answer

SOURCE: remote starter does not work but will unlock and lock doors.

I have a 2003 sierra and my remote starter would not work, it would lock and unlock only, checked out this site found the solution, tried it and in two seconds i solved the problem, Just press the lock button and the start button and viola it works again, thanks for all your help , GGGreat site glad i found it John

Posted on Jan 11, 2009

  • 2 Answers

SOURCE: I have ford ranger 2003,

You gatta find out if it has any type of theft system and most likely if it does then disconnect it because the computer for it may have malfuntioned and by u disconneting it will deactivate the security for the constint turning over and not starting... so figure that out first...

Posted on Jan 28, 2009

  • 1 Answer

SOURCE: Headlights cut out after being on 10 to 15 minutes

I had the same exact problem. I found that I could make the lights come on by pushing on the top connector on the front side of the lighting control module (LCM). I pulled the connector off, cleaned it and put it back together with some dielectric grease. Only time will tell if I fixed it. On my car, it would only have problems after the headlights had been on for about 3 hours; kind of hard to re-create.

Posted on Mar 24, 2009

  • 9 Answers

SOURCE: remote starter does not work but will unlock and lock doors.

depending on your alarm which it sounds like a viper model maybe? on my 02 you have to incorporate a factory alarm bypass module in order to be able to start the truck, they run about 100.00 bucks and have to be profssionally installed. The truck wont start because the computer isnt recieving the proper starting sequence due to the factory alarm

Posted on Jul 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 volvo xc90 will not stay running, it is giving a code of U0073 generic control module communication bus"a" off. .we have put in new crank sensor. the maf sensor is not the problem


Do you know what a serial data communication network is ? All the control modules on your vehicle share info on it . It stead of hard wiring all the componets on the vehicle they use control modules and a data network . U codes are problem codes assoicated with these networks . U0073 generic control module communication bus"a"OFF Has nothing to do with engine sensors ! Condition
The control modules transmit and receive information via a standardized serial communication method - CAN (Control Area Network).
The diagnostic trouble code (DTC) is stored if the control module detects that:
  • The control module does not have contact with the controller area network (CAN).
  • Incorrect value runs longer than 10 seconds.
The control module's test for the diagnostic trouble code (DTC) starts in the event of:
  • Starting the control module's CAN communication.
Note!The control module can only detect the fault once the test has been started and the diagnostic trouble code (DTC) is stored when the conditions are met. In the event of system communication problems, it is not possible to communicate with the control module. Therefore it will only be possible to read off the fault if it is intermittent. Substitute value
  • None.
Possible source
  • Open-circuit in terminals.
  • Damaged Parking Assistance Module (PAM).
Fault symptom[s]
  • Parking Assistance System, malfunction
  • Information lamp is on
  • Message in information display

A shorted module will cause the data bus to short and cause no start condition . You best bet , take it to a qualified repair shop . How to Diagnose Controller Area Network CAN

Jan 06, 2017 | 2005 Volvo XC90

1 Answer

Horn blows and lights flash when vehicle is parked


Hi Ron:
This is the ALARM function that is happening. It may be defective, and it may be that someone has your second set of keys and is goofing around. Rarely, there may be someone in your immediate vicinity that has the same remote code.
I see two choices, trouble shoot or disable the alarm.

Mar 09, 2015 | 2004 Chevrolet Venture Passanger

1 Answer

I own an AstroStart Model 2504A remote car starter. It was working fine until yesterday when all I get is a beep but no response from my Ford Edge. I thought the battery was weak and I replaced with a new...


If it was factory or dealer installed, you would probably be better off taking it to a Ford dealer with a good service dept.
I would not let any one work on it, if I did not know without question they knew what they were doing.

Nov 05, 2013 | Cars & Trucks

2 Answers

Astrostart won't start the car


You may need to reset the system.

SEQUENCE ACTIVATED BY THE PARKING BRAKE .
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply the parking brake Once Twice
Note: The system can be set - at time of installation - to require that the parking brake be applied once or twice.
If set for two actuations, pause one second between the two.
4. Remove key from ignition (the system keeps the engine running).
5. Exit the vehicle.
6. Within 60 seconds, close all doors.
7. The system will stop the engine and blink the parking brakes once to confirm the sequence is valid (vehicle is
ready for a remote start command).
SEQUENCE ACTIVATED BY THE REMOTE CONTROL
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply parking brake.
4. Send the start command (Model 801 & 2101 - Model 903 ).
5. Remove key from ignition (the system keeps the engine running).
6. Exit the vehicle.
7. Using the remote, send the STOP command. The system will stop the engine and parking lights will blink once
to confirm that the sequence is valid (vehicle is ready for a remote start command).
http://www.astrostart.com/Support/Guides.aspx

Nov 27, 2012 | Cars & Trucks

1 Answer

Engine won't start and shows trouble code P1516 and reduced engine power light is on


Here is the definition of the code.

Possible causes - Faulty Throttle Actuator Control (TAC) module
- Throttle Actuator Control (TAC) module harness is open or shorted
- Throttle Actuator Control (TAC) module circuit poor electrical connection (loose or broken wires)

P1516 CHEVROLET Description The Throttle Actuator Control (TAC) module contains data which is essential for proper TAC operation. The TAC module continuously test the integrity of this data. When the TAC module is unable to write or read data to and from Random Access Memory (RAM), or the TAC module is unable to correctly read data from the flash memory or and internal TAC module processor fault is detected and the Detected Trouble Code (DTC) is set.
Read more: http://engine-codes.com/p1516_chevrolet.html#ixzz286Gl3cSo

Sep 28, 2012 | 2002 Chevrolet TrailBlazer

2 Answers

2003 sunfire car is sputtering,when i start driving engine light flashes


Hello: The flashing engine light means there is a misfire (one or more cylinders not firing) Take it to Auto Zone, Advance Auto or O'Riely Auto parts stores, they can read the code and may not charge you. There are several reasons for a misfire: Fouled spark plug/bad spark plug, bad ignition wire. bad coil, bad ignition module, bad injector, bad engine control module. There is no way over the internet you can determine the exact cause. This condition will have to be found with hands on trouble shooting.

Feb 18, 2011 | Pontiac Sunfire Cars & Trucks

1 Answer

I need to figure out what wires to cross so that i can read my engine code and fix the problem so that my car starts, when i turn the key foward the engine lite comes on and flashes once and stays on...


You can't jump wires to read codes on this model.older modules you could.check engine light will come on and stay on with key in on position.this is normal.Check to see if security light is flashing after you try to crank engine.If so you have to relearn theft module by leaving ign key in run position for about 12 minutes until security light stops flashing.Very common problem

Feb 28, 2010 | 1996 Pontiac Grand Am

2 Answers

Have codea 12-19-30-41-52-91 f10-32 please help the car i have is a 1990 cad sedan de ville 4.5 engine


ECM Trouble Codes
12-Distributor signal fault
19-Fuel pump circuit fault (short)
30-Idle speed control (isc) motor rpm out of range
41-Camshaft position sensor (CMP) or circuit fault
52-Electric control module (ECM) reset
91-Park neutral position switch or coicuit fault

BCM Trouble Codes
10-Outside temperature sensor or circuit fault
32-Electronic control module (ECM) to Body control module (BCM) fault loss of communcation

Source: Haynes repair manual


Dec 11, 2009 | 1990 Cadillac Deville

1 Answer

Drive 4 light flashing when i put the key in.


This light is flashing to indicate a fault has occurred in the transmission, have a test run on the control module of the trans to figure out what that might be, it could be a simple fix once you have the trouble code.

Dec 05, 2008 | 1992 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...