Question about 2000 Daewoo Lanos

Open Question

Massive oil leak daewoo lanos - 2000 Daewoo Lanos

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: reset passcode for radio of 2002 daewoo ,lanos

MINE CAME ON A SMALL METAL TAG ON THE SPARE KEY

Posted on Jul 16, 2008

  • 1 Answer

SOURCE: User manual for daewoo lanos car

Need code to work radio. Replaced the battery and it is asking for a code for the radio to work

Posted on Feb 12, 2009

emissionwiz
  • 75744 Answers

SOURCE: Where is the timing mark for the camshaft on a 2000 Daewoo Lanos?

Here is the entire timing belt replacement procedure.
Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Posted on May 22, 2009

venexcsd
  • 1185 Answers

SOURCE: Is the gearbox on a 1998 daewoo lanos manual a sealed unit??


Just to confirm that the oil Fill plug to a Daewoo lano manual tansaxle is on the right hand side of the transaxle where the drive-shaft exits the gearbox housing.

You need to jack the car right up and use a torch

It takes 1.8L of oil

Posted on Jun 19, 2009

stevenhurc
  • 450 Answers

SOURCE: 2001 Daewoo Lanos Fault 63.58X 'B'

DTC 63 Will Set When
No voltage is supplied by the ECM through the EST “B” line while reference pulses are received by the ECM from the crankshaft position sensor
check white wire terminal B on ignition coil to ECM terminal C14 for open circuit or short to ground while disconnected if thats ok check for voltage signal at B while cranking no signal ECU faulty. voltage signal also on A terminal while cranking and check earth terminal C to body no higher than 5 Ohms
power is terminal D 12V
if getting power, earths good, and both signal voltages are going into coil pack, coil pack is faulty.

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why my daewoo leaks oil into the injectors?


The oil can't get into the injectors it must be getting around the injector body seal ,then causing this problem ,renew the seals .

Dec 20, 2014 | Daewoo Lanos Cars & Trucks

1 Answer

Daewoo lanos 2001


check spark plug gaps ,,,25th

Jun 26, 2017 | 2001 Daewoo Lanos

2 Answers

Coolant bottle in 200o Daewoo Lanos 1.6 is leaking


Replace the bottle.

It's to hard to weld together again...

Oct 31, 2009 | 2000 Daewoo Lanos

1 Answer

Possible oil leak from head gasket or crack in


if oil is leaking from the the top to bottom, check the gasket below the cover that has the daewoo name and sign on on top of the engine block. it could be cracked. replace with new one without any gasket sealant just replace the original and done

Oct 06, 2009 | 2000 Daewoo Lanos

2 Answers

2002 daewoo lanos oil leak coming from out of timing cover


either the bolts need tightening or the ghasket is broken through or a rusty timing cover has rusted through causubg a leak ...clean the cover off with a degreaser and wash off and clean it allow to dry then with engine runnibg visually inspect without getting hands or clothing caught in fan or other moving parts and look to see exactly where it is beginning from ....if it is a rusty leak some materials will help cease the leak as well as a ghasket maker sealant may be used as well to stop the leak ..let me know from where it is and what form of /type leak it is merely the bolts may be just loose !

Sep 24, 2009 | 2000 Daewoo Lanos

2 Answers

Oil leak/tacuma auto 2001


put it up in the air and have a good look around ,most likely is a connection ??

Jul 30, 2009 | 2001 Daewoo Lanos

1 Answer

Is the gearbox on a 1998 daewoo lanos manual a sealed unit??



Just to confirm that the oil Fill plug to a Daewoo lano manual tansaxle is on the right hand side of the transaxle where the drive-shaft exits the gearbox housing.

You need to jack the car right up and use a torch

It takes 1.8L of oil

Jun 19, 2009 | 2000 Daewoo Lanos

1 Answer

Which Oil do I put in 1997 Daewoo Lanos?


For the engine any regular 10w30 engine oil will be ok

Jan 09, 2009 | 1999 Daewoo Lanos

Not finding what you are looking for?
2000 Daewoo Lanos Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...