Question about Chevrolet Camaro

Open Question

Where is the map sensor located on a 1988 camaro iroc z

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

dr_layinlow
  • 60 Answers

SOURCE: starter on a 1988 camaro iroc z

go to your local auto zone or advance and get a manual and look it up!! hell jus go in with a friend and pick da book up and jus walk around like your looking and read up on it!! I would have to check others but im sure i people that know!! Let me know if you are unable to do this!

Posted on Dec 07, 2008

  • 6982 Answers

SOURCE: 88 camaro poor idle when engine is warm

Don't remember if they used an idle air control valve or mass air flow sensor on ones that old but either can do that. If not check your vacuum hoses for splits, cracks and good connections. You did not list engine size, but controls are pretty much the same. I'm pretty sure you can do a computer scan on those by jumping the under-dash connector...get a manual for codes and instructions on that.
good luck!

Posted on May 23, 2009

  • 1986 Answers

SOURCE: Starting problem with 1989 Camaro Iroc. Have

It could be your crank sensor is starting to act up

Posted on Aug 21, 2009

  • 3 Answers

SOURCE: 1988 Chevy Camaro Iroc Z

The engine fan switch is located in the right side cylinder head between the spark plugs. There are two different sizes that you might find installed, 5/16 or 9/16 inch threads.

Posted on Sep 02, 2009

  • 484 Answers

SOURCE: do you have a spark plug wiring diagram for a 1988

Okay, #1 is marked on the distributor so in clockwise order: 1-8-4-3-6-5-7-2
8 7
6 5
4 3
2 1
(Front)

Hope this helps,
matt

Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the horn relay located on a 1988 camaro?


I believe it is plugged into interior fuse box.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
https://ca.answers.yahoo.com/question/index?qid=20080504172413AA78RKW
Fuse box diagram for 1988 Camaro Iroc
1988 camaro fuse box location Google Search

Mar 19, 2016 | Cars & Trucks

1 Answer

How do i replace the rear axel bearings on a 1988 Chevrolet IROC Z28 Camaro


Put car in neutral, remove wheels, calipers and rotors, diff. cover. rotate carrier until you see wrist pin retaining bolt, remove bolt and slide out the wrist pin out of carrier. Next push axle inward to remove inner axle "C" retainer washer then slide axle out of tube. Then pry off axle seal and with slide hammer w/attachment remove axle bearing.

Feb 23, 2014 | 1988 Chevrolet Camaro

1 Answer

I have a 1988 iroc 305 tpi 5spd car runs fine till it gets hot. I have replaced pulgs,fuel pump,fuel filter,cap,rotor,wires,3 sensors.


might wanna check the fuel injectors when the start going bad they get a high resistance at engine normal temp

Jun 15, 2011 | 1988 Chevrolet Camaro

2 Answers

1988 camaro iroc z 350 tune port injected. need to reset timing on the computer. jodie


To set the ignition timing you will need to disconnect the electronic timing control. It is usually a dark brown and black wire located on the passenger side foot well where the carpet meets the firewall. Once the wire is disconnected, loosen the distributor and set the timing with a timing light. If you have an automatic transmission, I think the timing is 6deg BTDC. Tighten the distributor down and connect the ETC wire.

Mar 12, 2011 | 1988 Chevrolet Camaro

1 Answer

Where is the location of the temp sending unit in a 1988 camaro iroc z


On the thermostat housing. Please rate me on this answer.

Jun 11, 2010 | 1989 Chevrolet Camaro

1 Answer

I am serching for a schematic of a 1988 Iroc-Z ECU/ECM. I need information on pin locations to diagnose some issues with engine control items.


if you go to autozone you can buy a haynes book on you car for $20.00, its well worth it it will show you what your looking for.

Dec 31, 2009 | 1988 Chevrolet Camaro

1 Answer

Do you have a spark plug wiring diagram for a 1988 camaro iroc z 305 tpi


Okay, #1 is marked on the distributor so in clockwise order: 1-8-4-3-6-5-7-2
8 7
6 5
4 3
2 1
(Front)

Hope this helps,
matt

Oct 07, 2009 | 1988 Chevrolet Camaro

1 Answer

88 camaro poor idle when engine is warm


Don't remember if they used an idle air control valve or mass air flow sensor on ones that old but either can do that. If not check your vacuum hoses for splits, cracks and good connections. You did not list engine size, but controls are pretty much the same. I'm pretty sure you can do a computer scan on those by jumping the under-dash connector...get a manual for codes and instructions on that.
good luck!

May 23, 2009 | 1988 Chevrolet Camaro

2 Answers

1988 Chevy Camaro Iroc Z


below your rt fan should see underneath the car looking at the bottom of the radiator been a long time since i was arond the i roc but im pretty sure thats where it is

May 24, 2008 | 1988 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...