Question about Ford Futura

1 Answer

Engine runnig as if miss fireing just repalced all plugs as one was inop still running the same and engine warning light staying on ford fusion 1.6 duratec engine 04 plate

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 21,949 Answers

One cylinder not working???coil pack/or HT leads but if warning light on then its most likely the coil pack

Posted on Jan 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 fusion 2 oil warning light fuse where is it if there is one??


James I have in the recent past drove my car up to advance autos and they will plug in a computer for your car free of charge so you will positively know what is wrong. It may be the sending unit that screws into your engine block. I'll give you a link so you may locate one nearby: Advance Auto Parts Car Engine Batteries Brakes Replacement Performance... Thank you and best of luck. Please leave feedback.

Jul 13, 2016 | 2004 Ford Fusion

1 Answer

Need to know what code 2110 ford fusion 2006 se


P2110 2006 FORD FUSION P2110 2006 FORD FUSION - Throttle Actuator Control System - Forced Limited RPM 0 Comments ' Add Yours Possible causes - Faulty Throttle Actuator Control (TAC)
- Throttle Actuator Control (TAC) harness is open or shorted
- Throttle Actuator Control (TAC) circuit poor electrical connection help.png Help with this Symptoms - Engine Light ON (or Service Engine Soon Warning Light P2110 2006 FORD FUSION Description The TAC system is in the failure mode effects management (FMEM) mode of forced limited RPM.

Read more: http://helpforcars.net/obd_codes/p2110_2006_ford_fusion.html#ixzz3mV0SayWu

Sep 22, 2015 | 2006 Ford Fusion

1 Answer

What does 2110 code on 2006 ford fusion mean


P2110 2006 FORD FUSION P2110 2006 FORD FUSION - Throttle Actuator Control System - Forced Limited RPM 0 Comments ' Add Yours Possible causes - Faulty Throttle Actuator Control (TAC)
- Throttle Actuator Control (TAC) harness is open or shorted
- Throttle Actuator Control (TAC) circuit poor electrical connection > Help with this Symptoms - Engine Light ON (or Service Engine Soon Warning Light P2110 2006 FORD FUSION Description The TAC system is in the failure mode effects management (FMEM) mode of forced limited RPM.

Read more: http://helpforcars.net/obd_codes/p2110_2006_ford_fusion.html#ixzz3mUz73ACP

Sep 22, 2015 | 2006 Ford Fusion

1 Answer

My 2006 Ford Fusion seems to be experiencing an engine misfire. How do I find out the OBD code?


You well need a scanner, but even then Ford has some issues on miss fire detection in some vehicles, the ECM may need flashed to correct this problem.

If it works right it well point you to the right cylinder then you need to figure out if it's a plug, coil, boot over plug or some other problem.

May 25, 2012 | Ford Fusion Cars & Trucks

1 Answer

My 2004 Ford Escape has a bad miss as if it's only running on three cylenders, and some times will not start after the engin is warmed up.After it sets for several hours, it wil usually start, but run...


i have aford escape 2004 mdl only 3 cylinders running the first cylinder has a poor connections the check engine light stay on i have it read on a computer it says p0171 system too lean bank 1 what does this mean?

Aug 21, 2011 | 2004 Ford Escape

1 Answer

2005 sunfire.. service light stays on and when you start the car it makes a clicking sound and the headlights flicker off and on. They should stay on but don't unless you actually turn them on.


the daytime runnig lights are inoperative, could be the module, relay or a bulb, usually bad wiring, go to cavalier daytime running lights on the web,, there you will get diagnosis directions

Nov 17, 2010 | 2005 Pontiac Sunfire

1 Answer

I hooked up an amp for my stereo everything running fine till my fuse blew i put new one in on the main power line from battery to amp stereo works fine but now my valves miss fireing and heads winding bad...


Your amp as nothing to do with your car runnig bad. Your engine has a problem. It's miss fireing may be do to bad coil or even spark plugs or spark wires

Mar 06, 2010 | Honda Accord Cars & Trucks

1 Answer

2009 ford fusion engine light stays on steady


You just have to disconnect the battery for 1/2 hour. then reconnect and drive for 10 miles so computer can relearn your engine again. It may run rough. You should have the key off when refueling because computer sensed a fuel vapor leak during fueling and turned the light on.

Also, you can always drive with a check engine light on. It just means you are not meeting emissions. Do not drive if it's flashing on and off.

May 23, 2009 | 2006 Ford Fusion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

532 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...