Question about 1991 Ford Mustang

1 Answer

Blower fan only works on high 2003 focus

How do i check what is the problem switch or blower

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 4 Answers

If the high works and nothing else, I would feel confident replacing the blower motor resistor block. Probably not the switch. Definitely not the blower as it works.

Posted on Jan 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air condition and heat won't work


Check to see if you are getting voltage to the blower motor if you are the motor is bad if not check the fan speed switch. 1 2 3 or low medium high if you get voltage going to the switch but not from replace the switch if you have voltage from switch check the blower motor resistor the although with the blower resistor you commonly have a high fan speed in the max setting and the lower speed settings don't work wich would make you think 1 2 3 are not working but 4 is. That is why it is best to check all parts to make sure the part you do replace needed to be replaced

Oct 15, 2012 | 2000 Ford Focus

1 Answer

Blower only works on high speed in 2003 focus


BLOWER MOTOR WORK ONLY ONE SPEED.YOU COULD HAVE FAULTY BLOWER MOTOR RESISTOR OR BLOWER MOTOR CONTROL SWITCH BAD.USE VOLT METER CHECK VOLTAGE AT EACH CONTROL SWITCH SPEED TERMINAL. IF POWER IS AT EACH TERMINAL ON CONTROL SWITCH YOU MORE LIKELY HAVE A BAD BLOWER MOTOR RESISTOR.

Sep 26, 2011 | 2003 Ford Focus

1 Answer

A/c doesnt work on low fan


There is a blower motor resister that has gone bad,also check the blower switch on the back,the connection could be burned ,the blower motor causes this to happen,even though it sounds ok,it is drawing to many amps.

May 20, 2010 | 2000 Ford Focus

1 Answer

Fan blower stopped working


Hi Retta_roche,
This circuit is controlled through the switch. In the high position,it by-passes the blower resistor.So if the blower is off in the high position, and the fuse is good, you need to check the switch,blower motor or the wiring.Since the switch physically feels different,start there. Pull the switch and ground pin #4 blk/org wire with the key on. If the fan works,the switch is bad. You need to check the connector at the blower motor for evidence of a burn. If you find the connector burned,you will need to replace the motor and the connector. I am sending the wiring diagram to help you. If you need anything else,drop me a line. Thanks,Chuck d442985.gif

May 16, 2010 | 2000 Ford Focus

1 Answer

2003 expedition: heater control only works on 3 or 4. Why?


I would suspect the fan switch itself,if it only worked on high,it would be the blower resister.

Feb 01, 2010 | 2000 Ford Focus

1 Answer

Heater fan only works on fastest speed


Your blower motor resistor has gone bad, it should be located next to your blower motor in the car, held in place with a couple of screws, remove it and replace it. The resistor is responsible for making the blower motor run at slower speeds than high or (4). Let me know if this helps.

Jun 16, 2009 | 2000 Ford Focus

2 Answers

Ford focus 2003


well, check the fuse/relay then you will need to remove the control panel to access the switch then check the switch its self in all positions with a volt meter. if none of those things have found the prob then you prob have a bad blower motor. most likely its a fuse/relay usualy or a switch. when a motor goes it usually will still blow on high. if its out completely it ususaully smells like burnt tape.dont worry its prob something simple and cheap, ie fuse/relay. Let me know MrRodneyLong@gmail.com

Jul 13, 2008 | 1991 Ford Mustang

Not finding what you are looking for?
1991 Ford Mustang Logo

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...