Question about 2007 Mercedes-Benz C230 Sedan

Open Question

How to program a keyless remote key on a 2006 c230

Posted by Anonymous on

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I've replaced my battery on my 2006 Chevy Malibu per Howard's excellent advice on Fixya. Now my remote for the locks and trunk release does not work. I have to manually unlock my drivers side door. An


There is no manual on board procedure to program a keyless remote to this vehicle. This vehicle requires special equipment be connected to the vehicle to program the remote. Dealer fix

Feb 02, 2014 | 2006 Chevrolet Malibu

1 Answer

2006 pontiac g6 keyless remote programming


must take FOBs to dealer for programming.... there is no other way and it's cheap (you can take any number of FOBs and it's still a flat rate (~$40)

May 20, 2010 | 2006 Pontiac G6

1 Answer

Purchased a new clicker.from g/m.i can't program it.i have replaced the transformer under the dash panel that was used.. i have been told 96 models has several transmitters on it.


1. Move all Keyless Remotes out of range of vehicle. (10 to 15 feet)
2. Turn ignition key to the ON position.
3. Push the TRIP/ODO button on the DIC (Driver Info Center) twice.
4. Within 5 seconds, push & hold the FUEL INFO button on the DIC until
the PKE light comes on and stays on.
5. Turn the ignition to the OFF position, but leave the key in the ignition.
The PKE light will begin flashing.
6. Bring one Keyless Remote into range. The PKE light will stop flashing
and stay on to show the code is stored. Move the Keyless Remote out
of range. The PKE light will begin flashing indicating the system is ready
for the next Keyless Remote.
7. If more than one Keyless Remote is being programmed, move the first
Keyless Remote out of range and repeat step 6 for any additional Keyless
Remotes. Up to three Keyless Remotes can be programmed.
8. To turn off the programming mode, simply remove the key from the ignition
or turn the ignition switch on.
9. The programming mode will shut off after two minutes if.
A) You have not programmed any Keyless Remotes.
B) Removed the key from the ignition.
C) After three Keyless Remotes have been programmed.

Good luck and keep me posted.

Jan 23, 2010 | 1996 Chevrolet Corvette

1 Answer

Programing instructions for buick 2006 lacrossekeyless remote fob


Transmitter ProgrammingImportant: All transmitters which are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle.
  1. Install a scan tool.
  2. Use the scan tool in order to access programming: Vehicle Control System/Computer Integrating System/Module Setup/BCM/Program Key Fobs.
  3. Press the START soft key on the scan tool. Important: The scan tool must stay connected until all of the transmitters are programmed.
  4. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of 5-10 seconds, the scan tool will indicate that the transmitter is programmed.
  5. Repeat the previous step in order to program up to 4 transmitters.
  6. Remove the scan tool.
  7. Operate the transmitter functions in order to verify correct system operation.
Good luck

Dec 13, 2009 | 2006 Buick LaCrosse

2 Answers

Key fob not working after battery change ford focus 2006


Try reprogramming it.

1. Turn the ignition from OFF to RUN 4 times within 6 seconds.
2. Turn the ignition OFF. The system will chime to confirm programming mode.
3. Within 20 seconds, press any button on first keyless remote.
The system will chime once to confirm programming.

4. Within 20 seconds, press any button on second keyless remote.
System will chime once to confirm programming.

5. Turn ignition to RUN to exit programming mode.

May 28, 2009 | 2006 Ford Focus

1 Answer

2006 chevy equinox keyless remote programming


from the service manual:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Please go to the nearest GM dealer for assistance

Mar 26, 2009 | 2005 Chevrolet Equinox

1 Answer

Program a keyless remote on a 2006 impala


push relearn again then press and lock and unlock for about ten seconds till u hear beep

Feb 19, 2009 | 2006 Chevrolet Impala

1 Answer

Keyless entry remote


hello Kirk , follow these instructions carefully :

sitting in car with all the remotes you wish to register with the vehicle readily available ,,close all doors ! insert key into ignition and remove 6 times within 10 seconds ,, (hazzard warning lamps will then flash twice) ** note withdraw key completely from the cylinder each time ,, if procedure is done too fast it will not enter registration mode ,, ok ,, insert ignition key into cylinder and turn to the accessory position ,, Push any button on the key fob once ,, (hazzard warning lamps will then flash twice),, at this time the new ID code is entered ,, at this time open drivers door ,, check operation of all remotes ..

enjoy Mate .

Jan 04, 2009 | 2006 Nissan Altima

1 Answer

Keyless entry not working


Try re-programming the remotes, here is the procedure for your car.
JAGUAR
XJ8 Remote Control Programming
1. Unlock the trunk with key.
2. Turn Ignition on.
3. Warning light on dash comes on.
4. When they go out, lift arm rest, inside their is a valley button, Press 5 times within 5 secs of lights on dash going out, Horn & Lights Flash.
5. Press any button on remote, remote programmed

Dec 11, 2008 | 2006 Jaguar XJ8

2 Answers

Programming a 2006 Pontiac Gran Prix Keyless remote


The rke on 06 pontiac only can be programed using a diagnostic scan tool or Tech 2.
Conect the scan tool to the vehicle. turn key to on position.
Select 1 body, 2 them select special funtions
3 slect program key fob,
4 select the number of key fob you want to program.
5 Press and hold the lock and unlock key simultaneous. about 15 seconds
The power lock cycle confirm the remote is programed.

Jul 03, 2008 | 2006 Pontiac Grand Prix

Not finding what you are looking for?
2007 Mercedes-Benz C230 Sedan Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...