Question about 2000 Dodge Durango

1 Answer

Where to place the jack when changing a tire on a 2006 Pontiac Aztek?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dodge Master
  • 5,332 Answers

Look for the notches towards the front and rear of the pinch weld along the rockers.

Posted on Nov 28, 2012

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

cranegang
  • 21 Answers

SOURCE: where to i place the jack when changing a tire on a 2000 ddg dura

If you have the owners manual it will say where to exactly place the jack. If not one can be picked up at a junk yard for a couple of dollars. One thing they probably won't tell you in the owners manual is that when removing the tire to never put your hands at the 6 and 12 o'clock positions on the tire. I don't mean to scare you, but this is very dangerous due to the fact that if the vehicle slips off the jack your hands could get crushed either between the fender and the tire and/or between the tire and the ground. Always put your hands in the 3 and 9 o'clock positions on the tire when removing. And never crawl under the vehicle with the factory jack.
Hope this helps.

Posted on Jan 19, 2009

  • 4088 Answers

SOURCE: Good Afternoon. I am changing a tire on a 2006

The tire may need a good kick to loosen the rusted/corroded bond to the axle, usually in the center section. Light sanding and a film of grease to the area after the wheel is off will help future removal.

Posted on Jan 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Pontiac G6.. When accelerating the car pulls slightly to the left and when I let off it pulls back to the right. there is also a popping sound when turning. What could be the cause. My guess


it sounds like a ball joint or tie rod . you can jack up the front of the car and check one tire at a time, jack it up high enough to get the tire off the ground and shake it for play

Dec 07, 2012 | 2006 Pontiac G6

1 Answer

Need to replace pontiac aztek evaporation emission vent valve


This is located on the top/side of the gas tank on the drivers side of the tank. instructions for removal- jack the front left side of the car up, unbolt top bolt that holds the heat shield and evap canister up place another jack under gas tank before the strap. (i use the jack that comes with the car i find it easier) unbolt 1st strap lower the tank down there should be enough clearance to lower half of the tank down without droping the entire thing

Sep 25, 2012 | 2001 Pontiac Aztek

1 Answer

How to change front brake pads on 2006 town and country


Loosen tire lug nuts. Jack up the car and remove lug nuts and tire. Remove two bolts holding the caliper in place. Remove the the two bolts holding pads in place. Hang caliper with a wire from wheel so brake line is not stressed. Mount new calipers in correctly and tigthen pad bolts. Put caliper on and tighten caliper bolts. Replace tire and lugs nuts. Jack car down and tigheten lug nuts.

Aug 17, 2010 | 2006 Chrysler Town & Country

1 Answer

Change oil message stays on even after repeatedly cancelling


Pontiac Aztek, Montana 2001-05 w/o (DIC) Driver Information Center; Torrent, Ascender 2006

Turn the ignition to ON, with the engine off. Fully depress and release the accelerator pedal slowly three times within five seconds. Turn the key to OFF If the CHANGE ENGINE OIL’ message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.

Pontiac Aztek, Montana 2001-06 wI (DIC) Driver Information Center

urn the ignition to ON, with the engine off. Press the MODE button until the DIC reads ‘OIL LIFE LEFT/HOLD SET TO RESET Press and hold the SET button until 100% is displayed. You will hear three chimes and the “CHANGE ENGINE OIL” message will go off. Turn the key to OFF. If the “CHANGE ENGINE OIL” message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.

Good luck

Nov 10, 2009 | 2001 Pontiac Aztek

2 Answers

Do i have to pull the motor to change the oil pan gasket in my 2001 pontiac aztec?


no. just put the car on either ramps or jack stands. do not leave it on a jack. crawl under the car and you will find the oil pan on the bottom of the motor

Oct 28, 2009 | 2001 Pontiac Aztek

2 Answers

Where to place jack to change tire - 2006 Monte


There is a thin piece of metal that runs along the main portion of the car. Place jack on that thin metal that sticks down. On some models there are two tabs that stick down farther on the pinch weld "thin piece of meatal that sticks down." If the vechile have those two tabs the jack goes between them.

Sep 13, 2009 | 2006 Chevrolet Monte Carlo

3 Answers

Sand gring noise progressing


do you own jack stands ???
why not jack up the drive wheels and listen for noises ?

jack each wheel up independantly and run the car for a couple of minutes this will aallow you to clear some different noises off the list
push down on the bumber and support the axcell with a jack stand more noises gone from equasion

jack the drive wheels up 1 at a time start car put in gear and run to 20 miles or 30 km chalk the other wheels and do it where you have some space incase chit happens that shouldn't
this will allow you to track the noise to it's location

Jul 29, 2009 | 2003 Pontiac Aztek

2 Answers

Pontiac aztek awd disabled


Mine does this same thing...After taking it to the dealer and paying lots of money I found the solution my self while changing the Driver Side tire. Look behind the tire there should be a little plug for the abs if it comes un plugged in any way or loose then it will disable the AWD. Worked for me hope this works..

May 17, 2009 | 2002 Pontiac Aztek

1 Answer

Jack position to change rear tire 98 pontiac grand prix


factory jack to be placed in front of tire inbetween notches on seem. A manual floor jack can be used placing it under center connection bracket for rear wheels. Be shure to block front tires when using floor jack and have car in gear if a manual or park if automatic transmision.

Mar 31, 2009 | 2002 Pontiac Grand Prix

Not finding what you are looking for?
2000 Dodge Durango Logo

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...