Question about 2003 Chevrolet Silverado 2500HD

1 Answer

How to uninstall a safe-lite stealth anti theft system?

Safe lite stealth is causing truck not to crank.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 645 Answers

This might help. Unlock the door with your key, open it,shut it and lock with your key. Wait 20 seconds and unlock the door with your key. My alarm system shut down my ignition one day making it so that I couldn't start the car. My friend a radio tech told me this and it worked.----------------------------------------------------------------------------
zed-bull key programmer

Posted on Nov 28, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Car won't start, but engine turns over.

my car won't start, the anti theft system is on,

Posted on Mar 28, 2010

ilragatzzo78
  • 241 Answers

SOURCE: No start / start/ anti theft light?

MAY BE YOU HAVE A DEFECTIVE KEY, CHECK IF THE KEY HAS A PELLET IN IT, IF SO THE KEY IS BAD AND YOUR DEALER CAN REPLACE IT.
THE PELLET IS A RESISTOR FOR THE ANTITHEFT.

Posted on May 28, 2008

san luis
  • 11 Answers

SOURCE: i replaced it and the car will start

Try what we call a hard boot to the pcm. Disconnect the positive cable wire from the battery, enable the anti-thift system and than connect the positve cable back to the battery and see if that works

Posted on Apr 29, 2009

  • 580 Answers

SOURCE: car wont crank

Turn key on & off five times in a row. Wait 30 sec. & try again. If it doesn't start wait ten min. with key on & start car.

Posted on Sep 08, 2009

  • 1 Answer

SOURCE: anti-theft system activated need info on to

all dash lights keep coming on and either stay on or flash until you step on brake....also the dinger keeps dinging until you press on the brake.....we have had a tech work on it but have no idea whats going on.....HELP

Posted on Feb 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1994 dodge stealth is showing low oil level during idling.


the oil pump start to failor the oilsending unit.

Sep 16, 2012 | 1994 Dodge Stealth

1 Answer

Dash lites turn siagal and power windows all went ouit same time


probly a fuse-locate the box and owners book to view circuits--then pull and test the fuse------get a haynes manual at a parts place or mitchell books at library for complete details

Nov 05, 2011 | 1992 Dodge Stealth

2 Answers

Dodge stealth cranks no spark no check engine light. has fuel getting delivered to engine. checked all fuses all good. Ecu is good


Thanks for choosing FixYa and welcome to the site. There are a few things that you need to test and check. You need to check your plugs/coils, wires, distributor, coil packs, cam sensor and crank sensor. Check your timing belt/chain. Since there is no check engine light, you go in blind and you will have to check and test these parts, which some can be difficult. To perform the test, you will need a wiring schematic to test to see if any wires are without power. You will need to test these while the car is cranking. Check all electrical connectors and make sure all ground wires are grounded right. You need to check the wiring going from the parts listed to the ECU as well. You may be better off having your vehicle put on a diagnostic machine to pinpoint the cause. In most cases, it is electrical rather then the actual part.

Sep 06, 2011 | 1992 Dodge Stealth

3 Answers

I have a 1994 Dodge Stealth 3.0 DOHC Non Turbo. It won't start. It only gets fire on one coil. All teh coils are good fule pump works, New crank sensor, New spark plugs and wires, motor been port and...


look did u replace the censor where harmonic balancer is an the an the crank censor they are both like magnitos theres a metal fan blade looking thing that rotates through it make sure its not damaged an locked down let me know my email is lildevil6290@gmail.com

Mar 15, 2011 | 1994 Dodge Stealth

2 Answers

I used cam locks and belieseems that my crank sensor is not working now so I would like to know how to double check my timing marks before I close it up again. Can you help?ve I followed all the...


You should be able to remove the upper front forward cam-dust covers. With these out you should be able to align the cams to their timing marks. As for the crank you'll have to rely on the timing mark on the forward crank pulley/harmonic balancer.
I hope this may have assited you. If you in need of further info or images please send a note back.
Best regards,
Tom

Nov 08, 2009 | 1994 Dodge Stealth

1 Answer

I recentlr replaced 12 valves when i start my stealth it sounds good but after a few minutes it starts knocking could that be a knock senser plus where the crank shaft end there seems two be a place on the...


no did you juss put it in or was it like a couple weeks ago or something because when u replace all that stuff u have to take it easy for the first thousands miles at least

Oct 30, 2009 | 1991 Dodge Stealth

1 Answer

Where is the pully release on1991 dodge stealth


The 6g72 has 3 belts. the Alternator belt is loosened by a horizontal bolt on the tensional pulley just to the left of the crank pulley. it will move the pulley down and loosen the tension. the power steering belt is loosened by a 14mm bolt on a bracket up and to the left of the crank pulley its a very unique bolt not hard to spot. the Timing belt is loosened by loosening a bolt on the tensioner pulley (it will have 2 small holes on it and will be above and left of crank pulley and right of the hydralic tensioner. contact me at spammyiam@aol.com if you need pictures.

May 02, 2009 | 1991 Dodge Stealth

Not finding what you are looking for?
Cars & Trucks Logo

579 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...