Question about 2000 Mitsubishi Lancer

1 Answer

No guages working

Checked out circuit board all ok, I have all the earths, and battery and ignition positives check out ok.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 5,370 Answers

If all voltages checked ok, then most probably its faulty instrument cluster board on which gauges are connected. Yes if cluster circuit board looks ok, then also it can be faulty. Somewhere there is minute short or burn on board then such problem arises.


Also check the fuse box. One under hood and other under dash.

Inspect each and every fuse and see if all are fine or not.


---------------

For more troubleshooting on these cluster gauges I suggest you to refer the list of help links mentioned below. Its step by step instructions will help you to confirm the exact cause of problem in these conditions: ---------


Click the link below: ------


2004 Toyota Tundra: Oil Gauge and Temp Gauge Not Working?

http://howtobyme.blogspot.in/2012/05/2004-toyota-tundra-oil-gauge-and-temp.html

--------------

2005 Lexus SC430: Fuel Door, Dome light and Fuel Gauge Fuse Location?

http://howtobyme.blogspot.in/2012/05/2005-lexus-sc430-fuel-door-will-not.html

----------

Toyota 4Runner: Temperature Gauge Sensor

http://technoanswers.blogspot.in/2012/04/toyota-4runner-temperature-gauge-sensor.html

------------

Temperature gauge sits over half way mark?

http://schematicsdiagram.blogspot.in/2012/04/temperature-gauge-sits-over-half-way.html

---------------

Heater blows intermittently and temp gauge goes erratic?

http://technoanswers.blogspot.com/2012/01/heater-blows-intermittently-and-temp.html

----------

Temperature gauge does not move and no heat when heater is ON?

http://technoanswers.blogspot.com/2012/01/temperature-gauge-does-not-move-and-no.html

-----------

2003 Pontiac Grand Prix: Erratic Fuel Gauge?

http://technoanswers.blogspot.in/2012/06/2003-pontiac-grand-prix-erratic-fuel.html

-----------

Temperature gauge keeps fluctuating up and down close to red?

http://technoanswers.blogspot.com/2012/01/temperature-gauge-keeps-fluctuating-up.html

-------------

Temperature gauge on the dash quit working on Pontiac Grand Prix?

http://technoanswers.blogspot.com/2012/01/temperature-gauge-on-dash-quit-working.html

---------------

Fuel gauge jumps from empty to full?

http://schematicsdiagram.blogspot.com/2011/12/fuel-gauge-jumps-from-empty-to-full.html

--------------

Gas gauge stuck on empty on 2002 Mercedes Benz 240c?

http://repairhelpcenter.blogspot.in/2012/02/gas-gauge-stuck-on-empty-on-2002.html

---------------

Oldsmobile Temperature Gauge Lamp Switch?

-----------------

Fuel gauge drops to Empty?

http://technoanswers.blogspot.com/2012/01/fuel-gauge-drops-to-empty.html

----------------

Dodge neon gauges not working?

http://technoanswers.blogspot.in/2012/02/dodge-neon-gauges-not-working.html

------------

Temperature gauge went up?

http://schematicsdiagram.blogspot.com/2011/12/temperature-gauge-went-up.html

------------

Temperature gauge stays At cold on jaguar?

http://technoanswers.blogspot.in/2012/02/temperature-gauge-stays-at-cold-on.html

-----------

How to replace Instrument panel and dashboard on Toyota car?

http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-instrument-panel-and.html

-----------

How to remove instrument panel on Chevrolet car?

http://technoanswers.blogspot.in/2012/02/how-to-remove-instrument-panel-on.html

-----------

How to remove control panel on Buick regal?

http://howtobyme.blogspot.in/2012/02/how-to-remove-control-panel-on-buick.html

---------------


These details will help.

Thanks.

Posted on Nov 28, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 pacifica sunroof wont open or do anything . When I press the button i hear nothing no click no noise at all . All my fuses are working but i was told it could possibly be a relay ? any ideas woul


  1. Check the B+ 40 amp fuse in the Integrated Power Module (IPM). If OK, go to Step 2. If not OK, repair the shorted circuit or component as required and replace the inoperative fuse.
  2. Check the Accessory delay 20 amp fuse in the IPM. If OK, go to Step 3. If not OK, repair the shorted circuit or component as required and replace the inoperative fuse.
  3. Partially remove the headliner to access the sunroof motor/module.
  4. Disconnect the motor/module electrical connector. Using a voltmeter check for Battery voltage at the B+ terminal of the harness connector. If OK, go to Step 5. If not OK, repair the B+ circuit as necessary.
  5. With the ignition switch in the "RUN" position check for Battery voltage at the Accessory Relay Output terminal of the harness connector. If OK , go to Step 6. If not OK repair the Accessory Relay Output circuit as necessary.
  6. Using an ohmmeter test for continuity between the harness connector ground circuit and a known good ground. Continuity should be present. If OK go to Step 7. If not OK, repair the open ground circuit as necessary.
  7. Turn the ignition switch to the "OFF" position. Reconnect the motor/module electrical connector. With the ignition switch in the "RUN" position check for battery voltage on the "VENT", "CLOSE" and "OPEN" circuits at the back side of the motor/module connector. If OK, go to Step 8. If not OK replace the motor/module assembly

Mar 24, 2014 | 2004 Chrysler Pacifica

1 Answer

Diagnosis read fault p336


p0140 - 02 sensor circuit no activity detected, (bank 2 sensor 1)
P0170 - fuel trim malfunction (bank 1) MM6LP - fuel injection fault
P0336 - Crankshaft Position Sensor A Circuit range/performance SID801/4 - Engine speed signal coherence.
P0352 - Ignition coil B Primary/secondary circuit malfunction MM6LP - 2/3 ignition coil control. Open circuit, short circuit to positive, short circuit to earth. ME746 - NO.1 Ignition coil control function. Short circuit to earth. ME746 - NO.2 ign. coil control function. Short circuit to earth.
P0414 - Secondary Air Inj. system switching valve A circuit shorted. MM6LP - Air pump relay control failure.

Mar 21, 2014 | 2008 Peugeot 307cc 1.6

1 Answer

Guage Cluster Dose not work


Have the CPU program reset by using a code reader . When the battery is removed the CVPU program becomes corrupted . As to the radio you will need the radio security code to re set it.

Mar 01, 2014 | 1997 Chevrolet Venture

2 Answers

1998 dodge ram won,t start off key


make sure the starter is wired properly... you would be surprised how many people forget where the little wire from the solenoid goes.

Feb 11, 2014 | 1998 Dodge Ram 1500 4WD

1 Answer

What could be the problem if my dashboard lights are not working?


If your battery is ok and the ignition on and no lightsCheck fuses and fusable link. Fuses located in fuse box and all should be checked usind a test light with ign on,connect earth clip on test light to a good earth piont then with pointy end of tester touch each side of the fuses. power should be on both sides. Fuseable link located alongside main possitive on battery. sometimes blow and still look ok

Nov 26, 2012 | Cars & Trucks

1 Answer

SAAB 900 S 1996 not starting


I wouldn't think CPS if you are getting a good blue healthy spark.
Check your injector circuit with a test light: Pull off one injector connector, ground the test light, and probe the injector connector with key ON. If your injector drive circuit is working, one of the terminals on the injector connector should have a steady light. Now check the injector ground circuit: move the test light lead to the positive battery post, and probe the injector terminal that did not light the test light, while someone cranks the car over. If ground is working, you should have a blinking light, meaning the computer is properly groundind the injector to pulse. If both tests are good, the injector circuit is working properly. The drive circuit is routed through the ignition switch, and the ground circuit goes into the computer.

May 14, 2012 | Saab 900 Cars & Trucks

1 Answer

VW T4 transporter 1997. some times the engine turns over but will not start!!! but as soon as i put a jump pack on it fires up stright away. batterie checked ok. someone told me it could be a lazy starter...


most likly,if starter draws to much power-not enough power to ignition,but all think kiss--keep it simple stupid before removing starter check battery terminals,and all conections positive & earth

Aug 11, 2011 | 1997 Volkswagen Eurovan

2 Answers

It has power and everything works, but there is no power to the starter. We removed the starter and checked it and it is good.


there are 3 possiable causes.1the main red high power wire.2the earth wire/netural.3the small light wire leading from the ign switch any other wires are earth/neturel.one of these wires is broken my advice is get a meter to check power is going to the starter,is the power going to the main live from the battery.is the earth/netural from the battery to the connection to starter ok .and the main suspect the small wire from the ignition switch to the starter [ok]adrian.

Mar 15, 2011 | 2001 Chevrolet Blazer

1 Answer

Car cut out like no ignition, now no power to starter circuit. Battery new & hot


No power to starter circuit.The starter gets power from battery to start.So check the connection between battery to starter.As you mentioned battery is new ,but still get the battery voltage checked.It should be 12 volts if battery is fully charged.If battery shows 12 volt then check the connection terminal from battery to starter.If connection checked ok then its most probably the problem of faulty starter.It has to be replaced.But if the starter checked out ok by meter, then the problem relates to faulty ignition switch circuit causing this problem.Checking all this possibilities will rule out the exact faulty part causing the problem.----------Thanks.Helpmech.

Dec 02, 2010 | 2002 Ford Taurus

1 Answer

1999 malibu, engine turns, won't start, guages not


You checked all fuses? Dis-connect positive battery lead for a few seconds and reconnect. Do you have spark & fuel?

Aug 09, 2009 | 1999 Chevrolet Malibu

Not finding what you are looking for?
2000 Mitsubishi Lancer Logo

990 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...