Question about 2002 Nissan Altima

Open Question

P0507 idle relearn wont reset

Idles between 1200 to 1800 idle learn rest does not fix

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2002 nissan altima p0507 idle problem

I had the same problem before. after using the scanner i got a code number P0507. "Idle Air Control", New 2002 and up Nissan models like my Altima don't have an idle valve or sensor like older models to be replace. Here's the solution " Replace your "Throttle Chamber" the idle sensor is build in it, there is no other way to fix this problem. the throttle chamber is about $175.00 at your Nissan Dealer. The need your core or you will need to pay extra money. No need for expensive mechanic shop, you could do this your self. the throttle chamber is so easy to remove, four screws holds it together. I will take you about ten to twenty minutes to replace it. Please trust me and you will save big bucks!!!!!

Posted on Jan 13, 2009

marshalljc
  • 51 Answers

SOURCE: 2005 sentra idling high (1500rpms)

pull the IAC out and make sure that there is nothing blocking it from the throttle body from cleaning it. while you have it out go ahead and clean the IAC. the only way that I know to check it is pull it out and leave it plugged up to the connector turn the car on but dont start and see if the probe moves in or out.

Posted on Oct 22, 2009

  • 94 Answers

SOURCE: my 2005 altima idles high and engine code

This P0507 code is one that's sometimes triggered on vehicles that have electronic throttle control. That is, they don't have a regular throttle cable from the accelerator pedal to the engine. They rely on sensors and electronics to control the throttle. In this case, the P0507 DTC (diagnostic trouble code) is triggered when the PCM (powertrain control module) detects an engine idle speed that is greater than the desired (pre-programmed) RPM. In the case of GM vehicles (and possibly others) if the idle speed is over 200 rpm higher than expected, this code will be set.

Posted on Jun 07, 2010

  • 111 Answers

SOURCE: relearn idle on 2003 nissan

Does the fuel gauge work properly? Recently had to have fuel sender unit replaced and Nissan dealership service to reset the idle learn on 03 Sentra SE-R Spec V. Engine idle rpm would go up and down as a result of bad sender.

Posted on Dec 18, 2010

  • 237 Answers

SOURCE: Engine light on. p0507 code

after replacement of throttle control an idle air volme learn must be performed or you will have the identical symptoms you descibed.unfortunately the only way to do it is with a bi directional scan tool that supports this function or take to the dealer....about 90.00 to perform the procedure.there is no back door way to do it.

Posted on Apr 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to fix a dtc p0507?


A vacuum leak Leaking air intake after the throttle body EGR valve leaking vacuum A faulty positive crankcase ventilation (PCV) valve Damaged/failed/dirty throttle body Failed EVAP system Failed IAC (idle air controller) or faulty IAC circuit

Sep 28, 2015 | 2005 Nissan Altima

2 Answers

I have a the check code p0507 on my car Nissan altima coupe. Can someone help me with this


code p0507 refers to idle sped control (ISC) system--rpm higher than expected==causes --wiring--isc actuator--iac valve--throttle motor--throtle valve tight/sticking--ECM
it also refers to idle air control (IAC) system --circuit low==causes--wiring short to ground--IAC valve--ECM

Nov 12, 2014 | Cars & Trucks

1 Answer

Hy is there a code p0507? and how do i fix?


This P0507 code is one that's sometimes triggered on vehicles that have electronic throttle control. That is, they don't have a regular throttle cable from the accelerator pedal to the engine. They rely on sensors and electronics to control the throttle. In this case, the P0507 DTC (diagnostic trouble code) is triggered when the PCM (powertrain control module) detects an engine idle speed that is greater than the desired (pre-programmed) RPM. In the case of GM vehicles (and possibly others) if the idle speed is over 200 rpm higher than expected, this code will be set. A P0507 DTC trouble code may be caused by one or more of the following: A vacuum leak Leaking air intake after the throttle body EGR valve leaking vacuum A faulty positive crankcase ventilation (PCV) valve Damaged/failed/dirty throttle body Failed EVAP system Failed IAC (idle air controller) or faulty IAC circuit. This DTC is more of an informational code, so if there are any other codes set, diagnose them first. If there are no other codes, inspect the intake air system for air or vacuum leaks and damage. If there are no symptoms other than the DTC itself, just clear the code and see whether it returns. If you have an advanced scan tool that can interact with the car, command the idle higher and lower to see if the engine responds appropriately. Also check the PCV valve to see if it's blocked and needs to be replaced. Check the IAC (idle air controller) if equipped, verify it's operation. If available, try swapping in a new throttle body to see if that fixes the problem. On Nissan Altimas and possibly other vehicles the problem may be fixed by having the dealer perform an idle air relearn procedure, or other relearn procedure


Jul 27, 2014 | 1999 Daewoo Leganza

2 Answers

Code p0507


possible causes are:

Dirty throttle body
Electric throttle control actuator incorrectly adjusted/faulty/damaged
Air leak on Intake
Poor electrical connection to the Intake Air Control valve

P0507 KIA Idle Air Control IAC System RPM Higher Than Expected

May 14, 2014 | 2003 Kia Sedona

1 Answer

Code p0171 and p0507


A P0507 DTC trouble code may be caused by one or more of the following:
A vacuum leak
Leaking air intake after the throttle body
EGR valve leaking vacuum
A faulty positive crankcase ventilation (PCV) valve
Damaged/failed/dirty throttle body
Failed EVAP system
Failed IAC (idle air controller) or faulty IAC circuit.
Possible Solutions
This DTC is more of an informational code, so if there are any other codes set, diagnose them first. If there are no other codes, inspect the intake air system for air or vacuum leaks and damage. If there are no symptoms other than the DTC itself, just clear the code and see whether it returns. If you have an advanced scan tool that can interact with the car, command the idle higher and lower to see if the engine responds appropriately. Also check the PCV valve to see if it's blocked and needs to be replaced. Check the IAC (idle air controller) if equipped, verify it's operation. If available, try swapping in a new throttle body to see if that fixes the problem. On Nissan Altimas and possibly other vehicles the problem may be fixed by having the dealer perform an idle air relearn procedure, or other relearn procedures.

Jun 04, 2013 | 2008 Volkswagen Eos

1 Answer

Hi i have a code reading P0506 for a 06 GMC Envoy XL any recomondations


{: ) DTC P0506 Idle Speed Low
The usual cause is an excessive carbon build-up on the throttle body. If this is the case, I suggest you have your throttle body cleaned and perform an idle relearn procedure using a GM scan tool. The idle relearn or reset procedure is very important, otherwise this code may still remain even after a throttle body clean.
In a similar fashion, if the ECM/PCM (engine control module) of a high mileage vehicle is replaced and/or reprogrammed without performing the Throttle/Idle Learn procedure, the ECM/PCM may no longer compensate for existing carbon build up in the throttle body, causing it to return with a similar concern as well as DTCs P0121, P0506, and/or P0507.
There are other conditions that can also affect or reduce idle speed by increasing engine load like incorrect torque converter clutch (TCC) operation, accessories that require additional torque to operate, restricted exhaust, and mechanical conditions that limit engine speed.

Aug 02, 2011 | 2006 GMC Envoy

1 Answer

P507 buick regal 1998


P0507 - Idle Air Control (IAC) System RPM Higher Than Expected

This P0507 code is one that's sometimes triggered on vehicles that have electronic throttle control. That is, they don't have a regular throttle cable from the accelerator pedal to the engine. They rely on sensors and electronics to control the throttle. In this case, the P0507 DTC (diagnostic trouble code) is triggered when the PCM (powertrain control module) detects an engine idle speed that is greater than the desired (pre-programmed) RPM. In the case of GM vehicles (and possibly others) if the idle speed is over 200 rpm higher than expected, this code will be set.

Potential Symptoms: Most likely you'll notice the idle speed is higher than normal. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.

Causes: A P0507 DTC trouble code may be caused by one or more of the following:
* A vacuum leak
* Leaking air intake after the throttle body
* EGR valve leaking vacuum
* A faulty positive crankcase ventilation (PCV) valve
* Damaged/failed/dirty throttle body
* Failed EVAP system
* Failed IAC (idle air controller) or faulty IAC circuit

Possible Solutions: This DTC is more of an informational code, so if there are any other codes set, diagnose them first. If there are no other codes, inspect the intake air system for air or vacuum leaks and damage. If there are no symptoms other than the DTC itself, just clear the code and see whether it returns.

If you have an advanced scan tool that can interact with the car, command the idle higher and lower to see if the engine responds appropriately. Also check the PCV valve to see if it's blocked and needs to be replaced. Check the IAC (idle air controller) if equipped, verify it's operation. If available, try swapping in a new throttle body to see if that fixes the problem. On Nissan Altimas and possibly other vehicles the problem may be fixed by having the dealer perform an idle air relearn procedure, or other relearn procedures.


Hope this helps; keep us updated.

Feb 04, 2011 | 1998 Buick Regal

1 Answer

05 FOCUS P0-507 CODE


P0507 - Idle Air Control (IAC) System RPM Higher Than Expected

This P0507 code is one that's sometimes triggered on vehicles that have electronic throttle control. That is, they don't have a regular throttle cable from the accelerator pedal to the engine. They rely on sensors and electronics to control the throttle. In this case, the P0507 DTC (diagnostic trouble code) is triggered when the PCM (powertrain control module) detects an engine idle speed that is greater than the desired (pre-programmed) RPM. In the case of GM vehicles (and possibly others) if the idle speed is over 200 rpm higher than expected, this code will be set.

Potential Symptoms: Most likely you'll notice the idle speed is higher than normal. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.

Causes: A P0507 DTC trouble code may be caused by one or more of the following:
* A vacuum leak
* Leaking air intake after the throttle body
* EGR valve leaking vacuum
* A faulty positive crankcase ventilation (PCV) valve
* Damaged/failed/dirty throttle body
* Failed EVAP system
* Failed IAC (idle air controller) or faulty IAC circuit

Possible Solutions: This DTC is more of an informational code, so if there are any other codes set, diagnose them first. If there are no other codes, inspect the intake air system for air or vacuum leaks and damage. If there are no symptoms other than the DTC itself, just clear the code and see whether it returns.

If you have an advanced scan tool that can interact with the car, command the idle higher and lower to see if the engine responds appropriately. Also check the PCV valve to see if it's blocked and needs to be replaced. Check the IAC (idle air controller) if equipped, verify it's operation. If available, try swapping in a new throttle body to see if that fixes the problem. On Nissan Altimas and possibly other vehicles the problem may be fixed by having the dealer perform an idle air relearn procedure, or other relearn procedures.

Hope helps (remember comment and rated this).

Aug 05, 2010 | 2004 Ford Focus

3 Answers

My nissan is showing this code p0507. What is that mean.


idle controll system idle to high is the code description

Jun 09, 2010 | 2003 Nissan Maxima

3 Answers

My 2005 altima idles high and engine code


This P0507 code is one that's sometimes triggered on vehicles that have electronic throttle control. That is, they don't have a regular throttle cable from the accelerator pedal to the engine. They rely on sensors and electronics to control the throttle. In this case, the P0507 DTC (diagnostic trouble code) is triggered when the PCM (powertrain control module) detects an engine idle speed that is greater than the desired (pre-programmed) RPM. In the case of GM vehicles (and possibly others) if the idle speed is over 200 rpm higher than expected, this code will be set.

Jun 07, 2010 | 2005 Nissan Altima

Not finding what you are looking for?
2002 Nissan Altima Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...