Question about Honda Civic

Open Question

How to remove broken stud on 2009 honda fit - Civic Honda Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1214 Answers

SOURCE: Broken Lug Studs

You have to remove the hub to remove the bolts, if they won't come out by rotating the hub.

To remove the hub, take the cap off at the center of the hub (the cap would be poking you a the center of the hub, and is about 2 inches in diameter.

There should be a cotter key or something preventing the spindle nut from turning. Remove it. If there is a cover over the spindle nut, remove it. Take the spindle nut off. Pull lightly on the hub, and it will come off. Watch for the front bearing to pop out.

To reassemble, put hub back on spindle, put bearing and washer against bearing, thread on spindle nut and tighten while rotating hub. Back off 1/2 to 1 flat add cover (if used) and install cotter key.

Posted on Jan 29, 2009

Ad
emissionwiz
  • 77202 Answers

SOURCE: Front wheel stud on 2005 honda civic

U must remove the hub assembly to replace the stud.

Posted on Mar 24, 2009

  • 1596 Answers

SOURCE: broken wheel stud front left 1992 honda accord

Only if there is an Acsess Hole Directly Behind the STUD'S PUNCH THE Broken SHORT one OUT But there May Not Be Enough ROOM FOR the NEW LONG STUD to go in between the HUB & Rotor Check this FIRST If you see GOOD CLEARANCE TO GET The new STUD in Then just Drive the old one out , and Use A LARGER than Stud Nut Or Washers to Pull New Stud Threw some Before Putting Wheel on. Then Put Wheel on And Tighten Wheel , Retorque after a Few Hundred Miles.

Posted on Mar 29, 2009

  • 73 Answers

SOURCE: broke stud on front left side

you'll have to remove the brake caliper and the rotor , the smack the stud with a hammer to knock it out then get a lug nut stud installer may have at local parts store and you need a compressor and a air impact wrench or a good size breaker bar install stun and installer and tighten till pulls in like the others

Posted on Apr 16, 2009

Molson02536
  • 3854 Answers

SOURCE: Need to know how to remove broken studs?

Your going to have to remove the hub bearing unit to replace the studs.
The studs are pressed fit, so your going to have to press it out backwards. Don't try to hamer the studs out, you may damage the Hub bearing and you might as well change the whole hub if that's the case.
Once you have the hub removed press fit the studs out backward and if you don't have a press fit, you could get away with a clamp and lot's of washer and a pipe for leverage. 
To install the new studs, just follow in revers and press fit the new ones in place, it should take about 30 min to an hour to do. But take your time if you have not don this before.
Good luck and hope this helps, and if your have abs, make sure you line up your sensor before putting the wheels back on.

Posted on Apr 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a broken stud on 99 pontiac sunfire


hub studs are just a press in fit . the replacement can usually be done with out the hub removal. remove the drum /disc rotor
using a hammer and punch drive the broken stud out. place new stud in position and pull in to place using nut and spacers to get it home .
if you can remove the hub and drive the broken stud out . fit new stud and place the hub over something like a piece of pipe /socket the new stud in the pipe or socket) that is on something solid and hammer the new stud home.

Dec 26, 2014 | 1999 Pontiac Sunfire

1 Answer

How to replace a rear wheel stud


remove the wheel
using a hammer and punch knock the broken stud out
fit the new stud from behind use over size nuts as spacers fit the stud nut and apply tension
using the hammer and punch from the rear on the head of the stud knock it in as you keep the tension on the stud nut
keep the process going until the stud is fully seated on the head of the stud

Jul 10, 2014 | 2005 Toyota Camry Solara

2 Answers

My 91 Honda Accord EX wagon has a broken lug on front driver side. How do i fix it, & will it be ok in the meantime with the three lug nuts on tight?


It is not recommended to drive it like that. It's not too bad to replace but it depends on your level of mechanical skill, You need to remove the brake caliper and disc and then you can simply knock the remains of the broken stud out with a hammer and punch, To fit the new one insert the stud and then put a large nut over the thread, then fit the lug nut and tighten it to pull the stud into the hub, then simply remove the lug nut and put it all back together.

Jan 18, 2012 | Honda Accord Cars & Trucks

1 Answer

How to replace broken stud of honda crv 2001 front wheel


remove wheel, brake assembly & rotor. rotate to where the broken stud is in the opening where the brake assembly was. drive the broken stud out of the hub flange. then install the new stud by stacking washers on the new stud and tighten the lug till it pulls the new studs flange tight against the back side of the hub. remove lug and washers , reassemble .

May 25, 2011 | Honda CR-V Cars & Trucks

1 Answer

Removing a broken stud on front wheel


generally studs are press in thru the back of thr rotor. You need to remove the rotor and with a punch and hammer drive the broken piece out. Replacement studs are avaliable at any parts store.

Sep 20, 2009 | 2002 Honda Civic

1 Answer

Broken lug nut stud on 98 civic dx coupe


knock it out... use an old nut that will fit the new stud and install the stud. the nut will pull the stud in tight to the flange.

Jul 19, 2009 | 1998 Honda Civic

1 Answer

Broke stud on front left side


Yes you can replace the broken wheel stud. The wheel studs are pressed into place, and a vise will work to press it out, and in. You will have to remove the wheel hub, and then use a deep well socket and a bolt or something smaller than the actual stud to remove it with a vise. To replace it, you will need to use the deep well socket on the thread side of the stud, and press the new one in with the vise.

I hope this helps you, and I wish you luck with your repair.

Apr 25, 2009 | 2003 Pontiac Sunfire

1 Answer

Need to know how to remove broken studs?


Your going to have to remove the hub bearing unit to replace the studs.
The studs are pressed fit, so your going to have to press it out backwards. Don't try to hamer the studs out, you may damage the Hub bearing and you might as well change the whole hub if that's the case.
Once you have the hub removed press fit the studs out backward and if you don't have a press fit, you could get away with a clamp and lot's of washer and a pipe for leverage. 
To install the new studs, just follow in revers and press fit the new ones in place, it should take about 30 min to an hour to do. But take your time if you have not don this before.
Good luck and hope this helps, and if your have abs, make sure you line up your sensor before putting the wheels back on.

Apr 19, 2009 | Honda Civic Cars & Trucks

2 Answers

Broken wheel stud front left 1992 honda accord


Only if there is an Acsess Hole Directly Behind the STUD'S PUNCH THE Broken SHORT one OUT But there May Not Be Enough ROOM FOR the NEW LONG STUD to go in between the HUB & Rotor Check this FIRST If you see GOOD CLEARANCE TO GET The new STUD in Then just Drive the old one out , and Use A LARGER than Stud Nut Or Washers to Pull New Stud Threw some Before Putting Wheel on. Then Put Wheel on And Tighten Wheel , Retorque after a Few Hundred Miles.

Mar 29, 2009 | 1992 Honda Accord

1 Answer

Front wheel stud on 2005 honda civic


U must remove the hub assembly to replace the stud.

Mar 24, 2009 | 2005 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...