Question about 2002 Mazda Tribute

Open Question

How to change license plate bulb on mazda tribute

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: Can't remove bulb from socket/housing to replace plate light

Spray a little penetrating spray like WD-40, down into socket, give it a couple of minutes and wiggle from side to side & pull & see if that works.

Posted on Mar 27, 2009

Ad
  • 2 Answers

SOURCE: What is the Firing order to find the #1 cylinder on Mazda Tribute

#1 cylinder is on the back of the motor first one to the ritght. On the driver's side. the cylinders go 1,2,3 fromright to left on the back of motor as stand facing the vehicle and 4,5,6 left to right in the front of the motor as you face the vehicle. Hope you understand what I'm telling you.
Good luck,Dan

Posted on Apr 17, 2009

newrd1
  • 185 Answers

SOURCE: license plate light

through the trunk
open it
lift the matt you will see it

Posted on Feb 23, 2010

  • 60 Answers

SOURCE: changed the timing belt on my mazda 2001 tribute,

If it is a V6 it uses timing chain...not belt

Posted on May 15, 2010

mcdevito75
  • 1970 Answers

SOURCE: change brakes on 2006 mazda tribute

mcdevito75 here, That is a heavy duty job even for a good, good weekend mechanic, The truth is, as you know, you can run into a dozen problems that can and will leave you haveing to tow your vehicle to the shop. First you would need the TOOLs in American and Metric sizes as both American and Metric Nuts and Bolts are included on your Mazda, Then a Hydraulic jack that can hold at least 1 corner of the Mazda off the ground and--be able to with-stand the rocking motion as you did the job, Then you"d have to be concerned with parts, suppose you get the wrong parts, suppose you find a frozen or broken part, such as a brake hose, now you would have to bleed the brake system too. It"s very smart you are willing to do your own brakes BUT EVEN WISER TO KNOW, TO MANY PROBLEMS ASSOCIATED WITH THE JOB. BEST BET, look for a sale on Brakes with-in you area, The tools, time and effort even if the job went smoothly, would cost about the same as the shop. Look for a sale, and have the shop do your brakes.

Posted on Jul 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know how to replace the license plate bulb on a scion xa


Email Chris Bacon here: www.autolumination.com
*License Plate Light Bulb Size: 168
I buy all of my bulbs there.

Sep 09, 2012 | 2006 Scion xA

1 Answer

Mazda 6 sport sedan break lights not working after hid light conversion


Instructions Open the rear deck lid on the Mazda 6.Carefully remove the plastic finishing cover from the license plate light housing, using a small flat-head screwdriver to release the locking tabs. Pull the cover downward and off of the deck lid, exposing the license plate bulb.
Remove the old light bulb from the license plate bulb socket by hand. Wrap your new one in a paper towel and do not touch the bulb with your bare fingers. Insert the new bulb into the light socket. Install the finishing cover onto the light housing and push it upward until it clicks and locks into place.
Repeat Steps 2 and 3 to complete the LED light conversion on the opposite side of the deck lid. Test the new bulbs by turning on the headlights on the Mazda 6.
Mercedes Parts.






May 25, 2012 | 2004 Mazda 6

1 Answer

How do i replace the license plate bulb on my 1998 mazda 626?


Usually it is inside the trunk behind the plate take away the carpet and check it out ,good day.

Jan 02, 2011 | 1998 Mazda 626

1 Answer

2003 mazda tribute. How to change license plate bulbs. I can't get the plastic housing off.


It's easy, but may need some patience. No need to take off rear door inside panel! Press firmly on the left side of the light housing. It should move towards the right..then pull up slightly and it should pop out from the door panel. Twist the center bulb housing counterclockwise just slightly and the bulb should disconnect from the lense. Pull the bulb out...and replace with new bulb. Replace both sides if you like.

Nov 23, 2010 | 2003 Mazda Tribute

1 Answer

How do i change the license plate bulb on a 2004 tb ls


here is the instructions on how to replace license plate bulbs.

Remove the 2 screws that retain the license lamp lens to the liftgate.

  • Remove the license lamp lens from the liftgate.
  • Remove the bulb (1) from the socket.


  • 8e7cf48.gifaba90ae.gif

    Oct 11, 2010 | 2004 Chevrolet TrailBlazer

    1 Answer

    Is it hard to change the rear whell bearings on 05


    You are probably looking at about an hour per side. Brakes and backing plate must be removed. then the mounting bolts for the axle itself must be removed. this operation should be performed one side at a time in order to save the fluid inside the differential casing. It will become imperative that both oil seals are changed with the bearings. P.S. depending on the graciousness of the engineers, you may not have to remove the backing plates. Thank you, Dana

    Mar 05, 2010 | 2005 Mazda Tribute

    1 Answer

    License plate bulb 99 alero


    remove the 2 license lamp screws from outside,above the lic.plate then from insidethe trunk pull up the lic.lamp housing and replace the bulb.it should pull straight out

    Apr 21, 2009 | Oldsmobile Alero Cars & Trucks

    1 Answer

    Can't remove bulb from socket/housing to replace plate light


    Spray a little penetrating spray like WD-40, down into socket, give it a couple of minutes and wiggle from side to side & pull & see if that works.

    Mar 24, 2009 | 2001 Mazda Tribute

    Not finding what you are looking for?
    2002 Mazda Tribute Logo

    Related Topics:

    92 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mazda Experts

    yadayada
    yadayada

    Level 3 Expert

    77202 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22265 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8755 Answers

    Are you a Mazda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...